On Thu, Oct 25, 2018 at 02:56:53PM +0100, Biju Das wrote:
> Add USB PHY support for r8a77470 SoC. Renesas RZ/G1C (R8A77470)
> USB PHY is similar to the R-Car Gen2 family, but has the below
> features compared to other RZ/G1 and R-Car Gen2/3 SoCs
>
> It has a shared pll reset for usbphy0/usbphy1 and this register
> reside in usbphy0 block
>
> Each USB2.0 host needs to deassert the pll reset of usbphy0 block.
>
> Signed-off-by: Biju Das <biju....@bp.renesas.com>
> ---
> .../devicetree/bindings/phy/rcar-gen2-phy.txt | 64
> +++++++++++++++++++---
> 1 file changed, 55 insertions(+), 9 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt
> b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt
> index eeb9e18..0a59971 100644
> --- a/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt
> +++ b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt
> @@ -6,6 +6,7 @@ This file provides information on what the device node for
> the R-Car generation
> Required properties:
> - compatible: "renesas,usb-phy-r8a7743" if the device is a part of R8A7743
> SoC.
> "renesas,usb-phy-r8a7745" if the device is a part of R8A7745 SoC.
> + "renesas,usb-phy-r8a77470" if the device is a part of R8A77470
> SoC.
> "renesas,usb-phy-r8a7790" if the device is a part of R8A7790 SoC.
> "renesas,usb-phy-r8a7791" if the device is a part of R8A7791 SoC.
> "renesas,usb-phy-r8a7794" if the device is a part of R8A7794 SoC.
> @@ -23,13 +24,23 @@ Required properties:
> - clocks: clock phandle and specifier pair.
> - clock-names: string, clock input name, must be "usbhs".
>
> +Optional properties (r8a77470 SoC Only):
> +To use a USB channel as USB 2.0 Host, the device tree node should set below
> +optional properties. This is because USB2.0 Host needs to deassert pll reset,
> +apart from initializing interrupt enable, OVC detection timer and suspend/
> +resume timer register.
> +
> +- reg: offset and length of the partial USB2.0 Host register block.
USB host registers in the phy node? And somewhere else too? Don't create
overlapping regions in DT. That's not a reflection of the h/w and also
is an error in the kernel's resource handling code (which we work-around
in the DT code).
> +- clocks: clock phandle and specifier pair for usb2.0 host.
> +- clk-names: string, clock input name, must be "usb20_host".
Same with clocks.
> +
> The USB PHY device tree node should have the subnodes corresponding to the
> USB
> channels. These subnodes must contain the following properties:
> - reg: the USB controller selector; see the table below for the values.
> - #phy-cells: see phy-bindings.txt in the same directory, must be <1>.
>
> The phandle's argument in the PHY specifier is the USB controller selector
> for
> -the USB channel; see the selector meanings below:
> +the USB channel other than r8a77470 SoC; see the selector meanings below:
>
> +-----------+---------------+---------------+
> |\ Selector | | |
> @@ -40,22 +51,57 @@ the USB channel; see the selector meanings below:
> | 2 | PCI EHCI/OHCI | xHCI |
> +-----------+---------------+---------------+
>
> +For r8a77470 SoC see the selector meaning below:
> +
> ++-----------+---------------+---------------+
> +|\ Selector | | |
> ++ --------- + 0 | 1 |
> +| Channel \| | |
> ++-----------+---------------+---------------+
> +| 0 | EHCI/OHCI | HS-USB |
> ++-----------+---------------+---------------+
> +
> Example (Lager board):
>
> - usb-phy@e6590100 {
> - compatible = "renesas,usb-phy-r8a7790",
> "renesas,rcar-gen2-usb-phy";
> + usbphy: usb-phy@e6590100 {
> + compatible = "renesas,usb-phy-r8a7790",
> + "renesas,rcar-gen2-usb-phy";
This change doesn't seem necessary.
> reg = <0 0xe6590100 0 0x100>;
> #address-cells = <1>;
> #size-cells = <0>;
> - clocks = <&mstp7_clks R8A7790_CLK_HSUSB>;
> + clocks = <&cpg CPG_MOD 704>;
> clock-names = "usbhs";
> + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
> + resets = <&cpg 704>;
> + status = "disabled";
Don't show status in examples.
>
> - usb-channel@0 {
> - reg = <0>;
> - #phy-cells = <1>;
> + usb0: usb-channel@0 {
> + reg = <0>;
> + #phy-cells = <1>;
> + };
> + usb2: usb-channel@2 {
> + reg = <2>;
> + #phy-cells = <1>;
> };
> - usb-channel@2 {
> - reg = <2>;
> + };
> +
> +Example (iWave RZ/G1C SBC):
> +
> + usbphy0: usb-phy0@e6590100 {
> + compatible = "renesas,usb-phy-r8a77470",
> + "renesas,rcar-gen2-usb-phy";
> + reg = <0 0xe6590100 0 0x100>,
> + <0 0xee080200 0 0x118>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clocks = <&cpg CPG_MOD 704>, <&cpg CPG_MOD 703>;
> + clock-names = "usbhs", "usb20_host";
> + power-domains = <&sysc R8A77470_PD_ALWAYS_ON>;
> + resets = <&cpg 704>, <&cpg 703>;
> + status = "disabled";
Don't show status.
> +
> + usb0: usb-channel@0 {
> + reg = <0>;
> #phy-cells = <1>;
> };
> };
> --
> 2.7.4
>
