Hi Girish,
I re-tested the your patch.
How about locating into dw_mci_setup_bus()?
And if compare the previously and current busmode,
I think host needs not to re-write at register.
For example,
if (slot->bus_mode == ios->bus_mode)
return;
Then this patch looks good to me.
Best Regards,
Jaehoon Chung
On 07/26/2012 12:41 PM, Girish K S wrote:
> On 24 July 2012 18:37, Jae hoon Chung <[email protected]> wrote:
>> Hi Girish,
>>
>> Right, it be mentioned about the open-drain mode in synopsys spec.
>> But if didn't work on other board, there is some problem.
>> We can consider the location of set_busmode() .
> Sure. Currently i am setting the bus mode after sending the command
> during the clock setting. since the bus mode has affect on the cmd
> line i will try to move the location of calling bus mode before
> setting the clock.
> you can just check whether card gets detected by moving the set mode
> function just below the switch statement of bus width.
> On my board irrespective of the set bus mode location it works fine
>>
>> Best Regards,
>> Jaehoon Chung
>>
>> 2012/7/24 Girish K S <[email protected]>:
>>> On 24 July 2012 17:06, Girish K S <[email protected]> wrote:
>>>> On 24 July 2012 16:39, Jaehoon Chung <[email protected]> wrote:
>>>>> Hi Girish,
>>>>>
>>>>> Well..just tested on my board.
>>>>> this patch didn't work.(eMMC card didn't initialize)
>>>>> meaning of ios->bus_mode and synosys's bus_mode is same?
>>> Yes it is same. synopsys spec says this is specific to MMC
>>> initialization. when the card core sets this mode during
>>> initialization. the host has to set this bit
>>>>> How did you test this patch?
>>>> Tested it on exynos5 board using dt patches of thomas (with some
>>>> modification to his patch)
>>>>>
>>>>> Best Regards,
>>>>> Jaehoon Chung
>>>>>
>>>>> On 07/23/2012 08:16 PM, Girish K S wrote:
>>>>>> Synopsis Designware host controller has suppport for open
>>>>>> drain mode selection. During the mmc card initialization the
>>>>>> host controller can select the open-drain bit to allow the device
>>>>>> initialization in the open-drain mode. Once the device enters
>>>>>> the standby mode this bit can be reset to enter push-pull mode.
>>>>>>
>>>>>> Signed-off-by: Girish K S <[email protected]>
>>>>>> ---
>>>>>> drivers/mmc/host/dw_mmc.c | 14 ++++++++++++++
>>>>>> drivers/mmc/host/dw_mmc.h | 1 +
>>>>>> 2 files changed, 15 insertions(+), 0 deletions(-)
>>>>>>
>>>>>> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
>>>>>> index 72dc3cd..da11e5a 100644
>>>>>> --- a/drivers/mmc/host/dw_mmc.c
>>>>>> +++ b/drivers/mmc/host/dw_mmc.c
>>>>>> @@ -773,6 +773,18 @@ static void dw_mci_request(struct mmc_host *mmc,
>>>>>> struct mmc_request *mrq)
>>>>>> spin_unlock_bh(&host->lock);
>>>>>> }
>>>>>>
>>>>>> +static void dw_mci_set_busmode(struct dw_mci_slot *slot)
>>>>>> +{
>>>>>> + struct mmc_ios *ios = &slot->mmc->ios;
>>>>>> + u32 reg;
>>>>>> +
>>>>>> + reg = mci_readl(slot->host, CTRL);
>>>>>> + if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN)
>>>>>> + mci_writel(slot->host, CTRL, reg | SDMMC_CTRL_ENABLE_OD);
>>>>>> + else
>>>>>> + mci_writel(slot->host, CTRL, reg & ~SDMMC_CTRL_ENABLE_OD);
>>>>>> +}
>>>>>> +
>>>>>> static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
>>>>>> {
>>>>>> struct dw_mci_slot *slot = mmc_priv(mmc);
>>>>>> @@ -818,6 +830,8 @@ static void dw_mci_set_ios(struct mmc_host *mmc,
>>>>>> struct mmc_ios *ios)
>>>>>> default:
>>>>>> break;
>>>>>> }
>>>>>> +
>>>>>> + dw_mci_set_busmode(slot);
>>>>>> }
>>>>>>
>>>>>> static int dw_mci_get_ro(struct mmc_host *mmc)
>>>>>> diff --git a/drivers/mmc/host/dw_mmc.h b/drivers/mmc/host/dw_mmc.h
>>>>>> index 15c27e1..1a53fb2 100644
>>>>>> --- a/drivers/mmc/host/dw_mmc.h
>>>>>> +++ b/drivers/mmc/host/dw_mmc.h
>>>>>> @@ -67,6 +67,7 @@
>>>>>>
>>>>>> /* Control register defines */
>>>>>> #define SDMMC_CTRL_USE_IDMAC BIT(25)
>>>>>> +#define SDMMC_CTRL_ENABLE_OD BIT(24)
>>>>>> #define SDMMC_CTRL_CEATA_INT_EN BIT(11)
>>>>>> #define SDMMC_CTRL_SEND_AS_CCSD BIT(10)
>>>>>> #define SDMMC_CTRL_SEND_CCSD BIT(9)
>>>>>>
>>>>>
>>>>>
>>> --
>>> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
>>> the body of a message to [email protected]
>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
