Hi Sylwester,
On Sun, Aug 4, 2013 at 8:30 PM, Sylwester Nawrocki
<[email protected]> wrote:
> Hi Arun,
>
> On 08/02/2013 05:02 PM, Arun Kumar K wrote:
>>
>> This patch adds the crucial hardware pipeline control for the
>> fimc-is driver. All the subdev nodes will call this pipeline
>> interfaces to reach the hardware. Responsibilities of this module
>> involves configuring and maintaining the hardware pipeline involving
>> multiple sub-ips like ISP, DRC, Scalers, ODC, 3DNR, FD etc.
>>
>> Signed-off-by: Arun Kumar K<[email protected]>
>> Signed-off-by: Kilyeon Im<[email protected]>
>> ---
[snip]
>> +static int fimc_is_pipeline_isp_setparams(struct fimc_is_pipeline
>> *pipeline,
>> + unsigned int enable)
>> +{
>> + struct isp_param *isp_param =&pipeline->is_region->parameter.isp;
>> + struct fimc_is *is = pipeline->is;
>> + unsigned int indexes, lindex, hindex;
>> + unsigned int sensor_width, sensor_height, scc_width, scc_height;
>> + unsigned int crop_x, crop_y, isp_width, isp_height;
>> + unsigned int sensor_ratio, output_ratio;
>> + int ret;
>> +
>> + /* Crop calculation */
>> + sensor_width = pipeline->sensor_width;
>> + sensor_height = pipeline->sensor_height;
>> + scc_width = pipeline->scaler_width[SCALER_SCC];
>> + scc_height = pipeline->scaler_height[SCALER_SCC];
>> + isp_width = sensor_width;
>> + isp_height = sensor_height;
>> + crop_x = crop_y = 0;
>> +
>> + sensor_ratio = sensor_width * 1000 / sensor_height;
>> + output_ratio = scc_width * 1000 / scc_height;
>> +
>> + if (sensor_ratio == output_ratio) {
>> + isp_width = sensor_width;
>> + isp_height = sensor_height;
>> + } else if (sensor_ratio< output_ratio) {
>> + isp_height = (sensor_width * scc_height) / scc_width;
>> + isp_height = ALIGN(isp_height, 2);
>> + crop_y = ((sensor_height - isp_height)>> 1)& 0xFFFFFFFE;
>
>
> nit: Use ~1U instead of 0xFFFFFFFE.
>
>
>> + } else {
>> + isp_width = (sensor_height * scc_width) / scc_height;
>> + isp_width = ALIGN(isp_width, 4);
>> + crop_x = ((sensor_width - isp_width)>> 1)& 0xFFFFFFFE;
>
>
> Ditto.
>
>> + }
>> + pipeline->isp_width = isp_width;
>> + pipeline->isp_height = isp_height;
>> +
>> + indexes = hindex = lindex = 0;
>> +
>> + isp_param->otf_output.cmd = OTF_OUTPUT_COMMAND_ENABLE;
>> + isp_param->otf_output.width = pipeline->sensor_width;
>> + isp_param->otf_output.height = pipeline->sensor_height;
>> + isp_param->otf_output.format = OTF_OUTPUT_FORMAT_YUV444;
>> + isp_param->otf_output.bitwidth = OTF_OUTPUT_BIT_WIDTH_12BIT;
>> + isp_param->otf_output.order = OTF_INPUT_ORDER_BAYER_GR_BG;
>> + lindex |= LOWBIT_OF(PARAM_ISP_OTF_OUTPUT);
>> + hindex |= HIGHBIT_OF(PARAM_ISP_OTF_OUTPUT);
>> + indexes++;
>
>
> All right, let's stop this hindex/lindex/indexes madness. I've already
> commented on that IIRC. Nevertheless, this should be replaced with proper
> bitmap operations. A similar issue has been fixed in commit
>
>
>> + isp_param->dma1_output.cmd = DMA_OUTPUT_COMMAND_DISABLE;
>> + lindex |= LOWBIT_OF(PARAM_ISP_DMA1_OUTPUT);
>> + hindex |= HIGHBIT_OF(PARAM_ISP_DMA1_OUTPUT);
>> + indexes++;
>> +
>> + isp_param->dma2_output.cmd = DMA_OUTPUT_COMMAND_DISABLE;
>> + lindex |= LOWBIT_OF(PARAM_ISP_DMA2_OUTPUT);
>> + hindex |= HIGHBIT_OF(PARAM_ISP_DMA2_OUTPUT);
>> + indexes++;
>> +
>> + if (enable)
>> + isp_param->control.bypass = CONTROL_BYPASS_DISABLE;
>> + else
>> + isp_param->control.bypass = CONTROL_BYPASS_ENABLE;
>> + isp_param->control.cmd = CONTROL_COMMAND_START;
>> + isp_param->control.run_mode = 1;
>> + lindex |= LOWBIT_OF(PARAM_ISP_CONTROL);
>> + hindex |= HIGHBIT_OF(PARAM_ISP_CONTROL);
>> + indexes++;
>> +
>> + isp_param->dma1_input.cmd = DMA_INPUT_COMMAND_BUF_MNGR;
>> + isp_param->dma1_input.width = sensor_width;
>> + isp_param->dma1_input.height = sensor_height;
>> + isp_param->dma1_input.dma_crop_offset_x = crop_x;
>> + isp_param->dma1_input.dma_crop_offset_y = crop_y;
>> + isp_param->dma1_input.dma_crop_width = isp_width;
>> + isp_param->dma1_input.dma_crop_height = isp_height;
>> + isp_param->dma1_input.bayer_crop_offset_x = 0;
>> + isp_param->dma1_input.bayer_crop_offset_y = 0;
>> + isp_param->dma1_input.bayer_crop_width = 0;
>> + isp_param->dma1_input.bayer_crop_height = 0;
>> + isp_param->dma1_input.user_min_frametime = 0;
>> + isp_param->dma1_input.user_max_frametime = 66666;
>> + isp_param->dma1_input.wide_frame_gap = 1;
>> + isp_param->dma1_input.frame_gap = 4096;
>> + isp_param->dma1_input.line_gap = 45;
>> + isp_param->dma1_input.order = DMA_INPUT_ORDER_GR_BG;
>> + isp_param->dma1_input.plane = 1;
>> + isp_param->dma1_input.buffer_number = 1;
>> + isp_param->dma1_input.buffer_address = 0;
>> + isp_param->dma1_input.reserved[1] = 0;
>> + isp_param->dma1_input.reserved[2] = 0;
>> + if (pipeline->isp.fmt->fourcc == V4L2_PIX_FMT_SGRBG8)
>> + isp_param->dma1_input.bitwidth = DMA_INPUT_BIT_WIDTH_8BIT;
>> + else if (pipeline->isp.fmt->fourcc == V4L2_PIX_FMT_SGRBG10)
>> + isp_param->dma1_input.bitwidth =
>> DMA_INPUT_BIT_WIDTH_10BIT;
>> + else
>> + isp_param->dma1_input.bitwidth =
>> DMA_INPUT_BIT_WIDTH_12BIT;
>> + lindex |= LOWBIT_OF(PARAM_ISP_DMA1_INPUT);
>> + hindex |= HIGHBIT_OF(PARAM_ISP_DMA1_INPUT);
>> + indexes++;
>> +
>> + lindex = 0xFFFFFFFF;
>> + hindex = 0xFFFFFFFF;
>
>
> Hmm, is this a workaround for some firmware bug ? You're setting individual
> bits of lindex, hindex only to set them all to 1 just before using those
> variables ? WTH ? :)
>
We set this 0xffffff so that all the init params which are copied
earlier during pipeline_open
are set to the firmware. FW set_param cannot be done after copying of
init params since
FW expects isp params to be set correctly before accepting any other params.
So this is a workaround to force all init values to go along with the
ISP params.
>
> Anyway, instead of doing this:
>
> lindex |= LOWBIT_OF(A);
> hindex |= HIGHBIT_OF(A);
> indexes++;
>
> lindex |= LOWBIT_OF(B);
> hindex |= HIGHBIT_OF(B);
> indexes++;
>
> ...
>
> fimc_is_itf_set_param(..., indexes, lindex, hindex);
>
>
> You could do:
>
> u32 index[2];
>
> __set_bit(A, index);
>
> __set_bit(B, index);
>
> ...
>
> indexes = hweight32(index[0]);
> indexes += hweight32(index[1]);
>
> fimc_is_itf_set_param(..., indexes, index[0], index[1]);
>
> I.e. the bit operations work well with arbitrary length bitmaps.
>
Ok I will use this method.
> BTW, the firmware interface seems pretty odd with it's requirement to
> pass bitmask and number of bits set in this bitmaks separately. Does
> it ever allow 'indexes' to be different than number of bits set in
> lindex, hindex ? What happens in such case ?
Yes. It is working even when indexes is set as 0 !
I will remove that indexes field and use only bitmask.
Regards
Arun
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
