Hi, On Wed, Aug 27, 2014 at 03:14:18PM +0530, Naveen Krishna Chatradhi wrote: > Add initial device tree nodes for EXYNOS7 SoC. > Also, includes the dt-binding definitions for clock ids.
Uh, no -- it just adds the dtsi. > Signed-off-by: Naveen Krishna Chatradhi <ch.nav...@samsung.com> > Cc: Thomas Abraham <thomas...@samsung.com> > Cc: Rob Herring <r...@kernel.org> > Cc: Catalin Marinas <catalin.mari...@arm.com> > --- > arch/arm64/boot/dts/exynos7.dtsi | 553 > ++++++++++++++++++++++++++++++++++++++ > 1 file changed, 553 insertions(+) > create mode 100644 arch/arm64/boot/dts/exynos7.dtsi > > diff --git a/arch/arm64/boot/dts/exynos7.dtsi > b/arch/arm64/boot/dts/exynos7.dtsi > new file mode 100644 > index 0000000..6b9eaf4 > --- /dev/null > +++ b/arch/arm64/boot/dts/exynos7.dtsi Let's not make the same mistake as on 32-bit, and go with a directory hierarchy here from day one. So, please create a exynos subdirectory for this file. You also need a Makefile when you add a board dts. > @@ -0,0 +1,553 @@ > +/* > + * SAMSUNG EXYNOS7 SoC device tree source > + * > + * Copyright (c) 2014 Samsung Electronics Co., Ltd. > + * http://www.samsung.com > + * > + * SAMSUNG EXYNOS7 SoC device nodes are listed in this file. > + * EXYNOS7 based board files can include this file and provide > + * values for board specfic bindings. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +#include <dt-bindings/clock/exynos7-clk.h> > + > +/ { > + compatible = "samsung,exynos7"; > + interrupt-parent = <&gic>; > + #address-cells = <1>; > + #size-cells = <1>; You should probably use address-cells/size-cells 2/2 on a 64-bit platform. > + aliases { > + pinctrl0 = &pinctrl_0; > + pinctrl1 = &pinctrl_1; > + pinctrl2 = &pinctrl_2; > + pinctrl3 = &pinctrl_3; > + pinctrl4 = &pinctrl_4; > + pinctrl5 = &pinctrl_5; > + pinctrl6 = &pinctrl_6; > + pinctrl7 = &pinctrl_7; > + pinctrl8 = &pinctrl_8; > + pinctrl9 = &pinctrl_9; > + mshc0 = &mmc_0; > + mshc2 = &mmc_2; > + }; > + > + chipid@10000000 { > + compatible = "samsung,exynos4210-chipid"; > + reg = <0x10000000 0x100>; > + }; > + > + cpus { > + #address-cells = <2>; > + #size-cells = <0>; Why size-cells=2? Can you not fit a cpuid in 32 bits? > + cpu@0 { > + device_type = "cpu"; > + compatible = "arm,cortex-a57", "arm,armv8"; > + reg = <0x0 0x0>; > + }; > + }; > + > + fin_pll: xxti { > + compatible = "fixed-clock"; > + clock-frequency = <24000000>; > + clock-output-names = "fin_pll"; > + #clock-cells = <0>; > + }; > + > + gic: interrupt-controller@11001000 { > + compatible = "arm,gic-400"; > + #interrupt-cells = <3>; > + #address-cells = <0>; > + interrupt-controller; > + reg = <0x11001000 0x1000>, > + <0x11002000 0x1000>, > + <0x11004000 0x2000>, > + <0x11006000 0x2000>; > + }; > + > + hsi2c_0: hsi2c@13640000 { > + compatible = "samsung,exynos7-hsi2c"; Is the i2c controller here completely new? Also, please use 'i2c' for node name on these nodes. > + reg = <0x13640000 0x1000>; > + interrupts = <0 441 0>; > + #address-cells = <1>; > + #size-cells = <0>; > + pinctrl-names = "default"; > + pinctrl-0 = <&hs_i2c0_bus>; > + clocks = <&clock_peric0 PCLK_HSI2C0>; > + clock-names = "hsi2c"; > + status = "disabled"; > + }; > + > + hsi2c_1: hsi2c@13650000 { > + compatible = "samsung,exynos7-hsi2c"; > + reg = <0x13650000 0x1000>; > + interrupts = <0 442 0>; > + #address-cells = <1>; > + #size-cells = <0>; > + pinctrl-names = "default"; > + pinctrl-0 = <&hs_i2c1_bus>; > + clocks = <&clock_peric0 PCLK_HSI2C1>; > + clock-names = "hsi2c"; > + status = "disabled"; > + }; > + > + hsi2c_2: hsi2c@14E60000 { I much prefer lowercase hex in unit addresses (and reg entries) below. I know 32-bit uses uppercase, but let's switch going forward here. > + mct@101C0000 { > + compatible = "samsung,exynos4210-mct"; Please just do away with MCT here, and use architected timers going forward. There really shouldn't be a need to keep supporting MCT any more -- it's a construct from before arch timers on Cortex-A9. > + mmc_0: mmc@15740000 { > + compatible = "samsung,exynos7-dw-mshc-smu"; Is this controller backwards compatible with exynos5 ones? > + /* The Clock nodes are ordered as per the usermanual. */ "The clock" "user manual" > + timer { > + compatible = "arm,armv8-timer"; > + interrupts = <1 13 0xff01>, > + <1 14 0xff01>, > + <1 11 0xff01>, > + <1 10 0xff01>; > + clock-frequency = <24000000>; > + use-clocksource-only; > + use-physical-timer; These two properties are not standard, and I would expect any 64-bit platform to come with PSCI such that you have a way to initialize the virtual timers. -Olof -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
