Hi Javier, On Wed, Oct 21, 2015 at 3:46 PM, Javier Martinez Canillas <jav...@osg.samsung.com> wrote: > Hello Alim, > > On 10/21/2015 08:09 AM, Alim Akhtar wrote: > > [snip] > >>>>>> >>>>>> Hi Alim, >>>>>> >>>>>> I have installed your patch set above with git am on top of >>>>>> 4.3.0-rc6-00108-gce1fad2 torvalds/linux of today >>>>>> with make exynos_defconfig on Odroid U3. >>>>>> >>>>> which exynos soc Odroid U3 uses? >>>>> >>>> OK, I can see its uses exynos4412 and exynos4412-odroidu3.dts does >>>> include exynos4.dtsi, >>>> so these should have worked. >>>> >>>>>> "halt -p" worked (power 0.0W). >>>>>> "reboot" got stuck at 0.5W. >>>>>> >>>>> reboot stuck mean system does not reboot any more? >>> >>> It freezes when going for reboot. >>> Have to power off/on to boot again. >>> >>> Btw I use an mmc, not an sd-card. >>> No other HW connected, just LAN-cable. >>> Bootloader is u-boot v2015.10. >>> o >> Have checked on 4.3.0-rc6-00006-gd03c139e7e77, still works on peach boards. >> Sorry I don't have Odroid U3 with me, may be Javier or Krzysztof might help >> here to check whats wrong. To me its looks more of a board specific issue >> for now. >> > > Krzysztof has an Odroid XU3 lite and I have an Odroid XU4, both uses an > Exynos5422 so we can't check what's wrong with Odroid U3 (Exynos4412). > > Having said that I think I know what is the issue here. Markus said that > he is using an eMMC instead of an uSD (which is what I used and my guess > is that Krzysztof did too). > > Now, there is a subtle difference between the old PMU restart handler > and the syscon-reboot one, and that is the restart handler priorities: > > notifier priority > ------------------------------------ > pmu_restart_notify 128 > mmc_pwrseq_emmc_reset_nb 129 > syscon_restart_handle 192 > > So, without Alim's patches, first the eMMC reset handler will be called > and then the PMU restart handler but after his series, the syscon reset > handler has a higher priority so the eMMC reset will never be called. > > But the problem is that the eMMC card has to be properly reset on system > restart to allow the SoC iROM to be able to read the bootloader from the > eMMC since the iROM doesn't have restart logic and the card shouldn't be > left in an unknown state. > > So the problem here is not that the system is not being reset (that I > think that works) but that on reboot, the system is not able to boot > again since the ROM is not able to read the second stage bootloader. > > Markus, > > Can you please test following patch [0] on top of Alim's series? If that > works then it should either be part of Alim's series or the patches will > have to wait until that patch lands into mainline. I don't have an eMMC > to test it in XU4 but I'm pretty confident that it will solve the issue. > > Best regards, > -- > Javier Martinez Canillas > Open Source Group > Samsung Research America > > [0]: > From c9b250ee03bae338339b70693e906145c719f783 Mon Sep 17 00:00:00 2001 > From: Javier Martinez Canillas <jav...@osg.samsung.com> > Date: Wed, 21 Oct 2015 11:59:44 +0200 > Subject: [RFT PATCH] mmc: pwrseq: Use highest priority for eMMC restart > handler > > The pwrseq_emmc driver does a eMMC card reset before a system reboot to > allow broken or limited ROM boot-loaders, that don't have an eMMC reset > logic, to be able to read the second stage from the eMMC. > > But this has to be called before a system reboot handler and while most > of them use the priority 128, there are other restart handlers (such as > the syscon-reboot one) that use a higher priority. So, use the highest > priority to make sure that the eMMC hw is reset before a system reboot. > > Signed-off-by: Javier Martinez Canillas <jav...@osg.samsung.com> > --- Looks good. Reviewed-by: Alim Akhtar <alim.akh...@samsung.com>
> drivers/mmc/core/pwrseq_emmc.c | 6 +++--- > 1 file changed, 3 insertions(+), 3 deletions(-) > > diff --git a/drivers/mmc/core/pwrseq_emmc.c b/drivers/mmc/core/pwrseq_emmc.c > index 137c97fb7aa8..ad4f94ec7e8d 100644 > --- a/drivers/mmc/core/pwrseq_emmc.c > +++ b/drivers/mmc/core/pwrseq_emmc.c > @@ -84,11 +84,11 @@ struct mmc_pwrseq *mmc_pwrseq_emmc_alloc(struct mmc_host > *host, > > /* > * register reset handler to ensure emmc reset also from > - * emergency_reboot(), priority 129 schedules it just before > - * system reboot > + * emergency_reboot(), priority 255 is the highest priority > + * so it will be executed before any system reboot handler. > */ > pwrseq->reset_nb.notifier_call = mmc_pwrseq_emmc_reset_nb; > - pwrseq->reset_nb.priority = 129; > + pwrseq->reset_nb.priority = 255; > register_restart_handler(&pwrseq->reset_nb); > > pwrseq->pwrseq.ops = &mmc_pwrseq_emmc_ops; > -- > 2.4.3 -- Regards, Alim -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
