Hi Guys,
I am having problems with using a scanner, After a few scans, (not the same
number each time), then scanner fails to be recognised. If I wait for some
time the scanner appears to be ok, ie I can use it to make one scan, but it
will lock the machine solid after a short time after the second scan. No
errors recorded in any logs that I can find.
I have the scanner (UMAX 2400S) attached to a separate SCSI card and advansys
3940uw. All the system disks are on another SCSI card (same make/number). I
have not had any problems with this card when access HDD's CD's CDRW's.
The Scanner is attached to the card by a 50pin Centronics (on the scanner) to
50pin High-Density (on the card) cable. It is then converted to 68pin as
required by the card by an active converter (as suggested by some docs that I
read for an adaptect scsi card) so that it properly terminates the high bytes
on the scsi socket. The other scsi port on the Scanner is terminated with an
active 25pin d-type connector (The LED does light).
All the cables are new, I have even replaced the active terminator, cables
etc.
I have had the same lockups when the scanner was connected to the same card
as the drives and was conneted to the card via a 50pin centronics to 68pin
high density cable (No converters). The SCSI cable is only 1 meter in length.
I have even booted the system with a single processor kernel just to be sure.
The system is a standard install of mandrake 7.2.
Kernel is 2.2.17-21mdksmp, it that means anything to non-mandrake users.
The machine is a dual processor 400MHz job, Asus motherboard P2BD with 256MB
mem.
The output of the advansys /proc/scsi/advansys/1 (the card where the scanner
is attached) is attached to this msg (Both single processor and dual
processor) as well as two versions of dmsg.
SCSI Id of the scanner is 1.
The only thing that might be odd is that the scanner's scsi card and the
display card are using the same IRQ, but I thought that IRQ sharing was ok in
the new kernels. The display card is an AGP type and the scsi card is pci.
As you might have guessed, I am at a loss as to what to do next. Any help
appriciated, even suggestions as to how I can track down what I haven't done
(yet!)
--
Stephen Kitchener
Linux version 2.2.17-21mdk ([EMAIL PROTECTED]) (gcc version 2.95.3 19991030
(prerelease)) #1 Thu Oct 5 13:16:08 CEST 2000
Detected 400918 kHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 799.54 BogoMIPS
Memory: 256960k/262080k available (1136k kernel code, 416k reserved, 3024k data, 128k
init, 0k bigmem)
Dentry hash table entries: 32768 (order 6, 256k)
Buffer cache hash table entries: 262144 (order 8, 1024k)
Page cache hash table entries: 65536 (order 6, 256k)
VFS: Diskquotas version dquot_6.4.0 initialized
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel Pentium II (Deschutes) stepping 02
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch ([EMAIL PROTECTED])
PCI: PCI BIOS revision 2.10 entry at 0xf0730, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 262144 bhash 65536)
Initializing RT netlink socket
Starting kswapd v 1.5
Detected PS/2 Mouse Port.
Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.13)
Real Time Clock Driver v1.09
RAM disk driver initialized: 16 RAM disks of 4096K size
Uniform Multi-Platform E-IDE driver Revision: 6.30
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 21
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:pio
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
raid5: measuring checksumming speed
raid5: MMX detected, trying high-speed MMX checksum routines
pII_mmx : 906.018 MB/sec
p5_mmx : 923.163 MB/sec
8regs : 695.325 MB/sec
32regs : 410.337 MB/sec
using fastest function: p5_mmx (923.163 MB/sec)
scsi : 0 hosts.
scsi : detected total.
md.c: sizeof(mdp_super_t) = 4096
Partition check:
RAMDISK: Compressed image found at block 0
autodetecting RAID arrays
autorun ...
... autorun DONE.
VFS: Mounted root (ext2 filesystem).
scsi0 : AdvanSys SCSI 3.2M: PCI Ultra-Wide: BIOS CC000/7FFF, IO B400/3F, IRQ 10
scsi1 : AdvanSys SCSI 3.2M: PCI Ultra-Wide: BIOS D0000/7FFF, IO B000/3F, IRQ 11
scsi : 2 hosts.
Vendor: IBM Model: DNES-309170 Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
Vendor: PIONEER Model: CD-ROM DR-U12X Rev: 1.06
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 2, lun 0
Vendor: HP Model: CD-Writer+ 9200 Rev: 1.0c
Type: CD-ROM ANSI SCSI revision: 04
Detected scsi CD-ROM sr1 at scsi0, channel 0, id 3, lun 0
Vendor: IBM Model: DNES-309170 Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Detected scsi disk sdb at scsi0, channel 0, id 4, lun 0
Vendor: HP Model: C1533A Rev: A812
Type: Sequential-Access ANSI SCSI revision: 02
Vendor: IBM Model: DNES-309170 Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Detected scsi disk sdc at scsi0, channel 0, id 6, lun 0
Vendor: UMAX Model: Astra 2400S Rev: V1.1
Type: Scanner ANSI SCSI revision: 02
sr0: scsi3-mmc drive: 12x/12x xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.11
sr1: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
SCSI device sda: hdwr sector= 512 bytes. Sectors= 17916240 [8748 MB] [8.7 GB]
sda: sda1 sda2 < sda5 sda6 sda7 sda8 >
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 17916240 [8748 MB] [8.7 GB]
sdb: sdb1
SCSI device sdc: hdwr sector= 512 bytes. Sectors= 17916240 [8748 MB] [8.7 GB]
sdc: sdc1
autodetecting RAID arrays
autorun ...
... autorun DONE.
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 128k freed
Adding Swap: 248968k swap-space (priority -1)
st: bufsize 32768, wrt 30720, max buffers 5, s/g segs 16.
Detected scsi tape st0 at scsi0, channel 0, id 5, lun 0
es1371: version v0.22 time 13:20:20 Oct 5 2000
es1371: found chip, vendor id 0x1274 device id 0x1371 revision 0x06
es1371: found es1371 rev 6 at io 0xd000 irq 9
es1371: features: joystick 0x0
es1371: codec vendor TRA (0x545241) revision 35 (0x23)
es1371: codec features none
es1371: stereo enhancement: no 3D stereo enhancement
ne2k-pci.c:vpre-1.00e 5/27/99 D. Becker/P. Gortmaker
http://cesdis.gsfc.nasa.gov/linux/drivers/ne2k-pci.html
ne2k-pci.c: PCI NE2000 clone 'RealTek RTL-8029' at I/O 0xb800, IRQ 5.
eth0: RealTek RTL-8029 found at 0xb800, IRQ 5, 00:80:C8:FC:84:11.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.232 $ time 13:21:03 Oct 5 2000
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: Intel USB controller: setting latency timer to 0
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
usb.c: USB new device connect, assigned device number 1
hub.c: USB hub found
hub.c: 2 ports detected
parport0: PC-style at 0x378 (0x778) [SPP,ECP,ECPEPP,ECPPS2]
parport0: detected irq 7; use procfs to enable interrupt-driven operation.
parport_probe: succeeded
parport0: Printer, HEWLETT-PACKARD DESKJET 660C
lp0: using parport0 (polling).
kdeinit uses obsolete /proc/pci interface
isapnp: No Plug & Play device found
AdvanSys SCSI 3.2M: PCI Ultra-Wide: BIOS CC000/7FFF, IO B400/3F, IRQ 10
ROM BIOS Version: 3.1I
Device Information for AdvanSys SCSI Host 0:
Target IDs Detected: 0, 2, 3, 4, 5, 6, 7, (7=Host Adapter)
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: IBM Model: DNES-309170 Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi0 Channel: 00 Id: 02 Lun: 00
Vendor: PIONEER Model: CD-ROM DR-U12X Rev: 1.06
Type: CD-ROM ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 03 Lun: 00
Vendor: HP Model: CD-Writer+ 9200 Rev: 1.0c
Type: CD-ROM ANSI SCSI revision: 04
Host: scsi0 Channel: 00 Id: 04 Lun: 00
Vendor: IBM Model: DNES-309170 Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi0 Channel: 00 Id: 05 Lun: 00
Vendor: HP Model: C1533A Rev: A812
Type: Sequential-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 06 Lun: 00
Vendor: IBM Model: DNES-309170 Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
EEPROM Settings for AdvanSys SCSI Host 0:
Serial Number: AA48A919D407
Host SCSI ID: 7, Host Queue Size: 253, Device Queue Size: 63
termination: 0 (Automatic), bios_ctrl: ffe7
Target ID: 0 1 2 3 4 5 6 7 8 9 A B C D E F
Disconnects: Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Command Queuing: Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Start Motor: Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Synchronous Transfer: Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Ultra Transfer: Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Wide Transfer: Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Linux Driver Configuration and Information for AdvanSys SCSI Host 0:
host_busy 0, last_reset 0, max_id 16, max_lun 8, max_channel 0
unique_id 0, can_queue 253, this_id 7, sg_tablesize 255, cmd_per_lun 1
unchecked_isa_dma 0, use_clustering 1, loaded_as_module 1
flags c, last_reset 0, jiffies 8437
queue_depth: 0:63 2:63 3:63 4:63 5:63 6:63
Linux Driver Statistics for AdvanSys SCSI Host 0:
command 0, queuecommand 8310, abort 0, reset 0, biosparam 3
interrupt 8297, callback 8310, done 8310
exe_noerror 8310, exe_busy 0, exe_error 0, exe_unknown 0
build_error 0, build_noreq 0, build_nosg 0
cont_cnt 4755, cont_xfer 13940.5 kb avg_xfer 2.9 kb
sg_cnt 3555, sg_elem 21277, sg_xfer 82776.0 kb
avg_num_elem 5.9, avg_elem_size 3.8 kb, avg_xfer_size 23.2 kb
Active and Waiting Request Queues (Time Unit: 100 HZ):
target 0
active: cnt [cur 0, max 63, tot 7995], time [min 0, max 69, avg 4.2]
waiting: cnt [cur 0, max 0, tot 0], time [min 0, max 0, avg 0.0]
target 2
active: cnt [cur 0, max 1, tot 3], time [min 0, max 0, avg 0.0]
waiting: cnt [cur 0, max 0, tot 0], time [min 0, max 0, avg 0.0]
target 3
active: cnt [cur 0, max 1, tot 3], time [min 0, max 1, avg 0.3]
waiting: cnt [cur 0, max 0, tot 0], time [min 0, max 0, avg 0.0]
target 4
active: cnt [cur 0, max 1, tot 149], time [min 0, max 11, avg 0.7]
waiting: cnt [cur 0, max 0, tot 0], time [min 0, max 0, avg 0.0]
target 5
active: cnt [cur 0, max 1, tot 2], time [min 1, max 1, avg 1.0]
waiting: cnt [cur 0, max 0, tot 0], time [min 0, max 0, avg 0.0]
target 6
active: cnt [cur 0, max 1, tot 149], time [min 0, max 11, avg 0.7]
waiting: cnt [cur 0, max 0, tot 0], time [min 0, max 0, avg 0.0]
Adv Library Configuration and Statistics for AdvanSys SCSI Host 0:
iop_base d001e000, cable_detect: 1, err_code 0
chip_version 64, lib_version 505, mcode_date 136a, mcode_version 505
Queuing Enabled: 0:Y 2:N 3:N 4:Y 5:N 6:Y
Queue Limit: 0:63 2:1 3:1 4:63 5:1 6:63
Command Pending: 0:0 2:0 3:0 4:0 5:0 6:0
Wide Enabled: 0:N 2:N 3:N 4:N 5:N 6:N
Transfer Bit Width: 0:8 2:8 3:8 4:8 5:8 6:8
Synchronous Enabled: 0:Y 2:Y 3:Y 4:Y 5:Y 6:Y
0: Transfer Period Factor: 12 (20.8 Mhz), REQ/ACK Offset: 15
2: Transfer Period Factor: 25 (10.0 Mhz), REQ/ACK Offset: 15
3: Transfer Period Factor: 25 (10.0 Mhz), REQ/ACK Offset: 15
4: Transfer Period Factor: 12 (20.8 Mhz), REQ/ACK Offset: 15
5: Transfer Period Factor: 25 (10.0 Mhz), REQ/ACK Offset: 15
6: Transfer Period Factor: 12 (20.8 Mhz), REQ/ACK Offset: 15
Linux version 2.2.17-21mdksmp ([EMAIL PROTECTED]) (gcc version 2.95.3 19991030
(prerelease)) #1 SMP Thu Oct 5 13:03:01 CEST 2000
Intel MultiProcessor Specification v1.1
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #1 Pentium(tm) Pro APIC version 17
Processor #0 Pentium(tm) Pro APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Processors: 2
mapped APIC to ffffe000 (fee00000)
mapped IOAPIC to ffffd000 (fec00000)
Detected 400913 kHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 799.54 BogoMIPS
Memory: 256840k/262080k available (1200k kernel code, 420k reserved, 3064k data, 140k
init, 0k bigmem)
Dentry hash table entries: 32768 (order 6, 256k)
Buffer cache hash table entries: 262144 (order 8, 1024k)
Page cache hash table entries: 65536 (order 6, 256k)
VFS: Diskquotas version dquot_6.4.0 initialized
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch ([EMAIL PROTECTED])
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
per-CPU timeslice cutoff: 100.09 usecs.
CPU1: Intel Pentium II (Deschutes) stepping 02
calibrating APIC timer ...
..... CPU clock speed is 400.9351 MHz.
..... system bus clock speed is 100.2334 MHz.
Booting processor 0 eip 2000
Calibrating delay loop... 801.18 BogoMIPS
Intel machine check reporting enabled on CPU#0.
OK.
CPU0: Intel Pentium II (Deschutes) stepping 02
Total of 2 processors activated (1600.72 BogoMIPS).
enabling symmetric IO mode... ...done.
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-9, 2-10, 2-11, 2-13, 2-20, 2-21, 2-22, 2-23 not
connected.
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00170011
....... : max redirection entries: 0017
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 000 00 0 0 0 0 0 1 1 59
02 0FF 0F 0 0 0 0 0 1 1 51
03 000 00 0 0 0 0 0 1 1 61
04 000 00 0 0 0 0 0 1 1 69
05 000 00 1 0 0 0 0 0 0 00
06 000 00 0 0 0 0 0 1 1 71
07 000 00 0 0 0 0 0 1 1 79
08 000 00 0 0 0 0 0 1 1 81
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 000 00 0 0 0 0 0 1 1 89
0d 000 00 1 0 0 0 0 0 0 00
0e 000 00 0 0 0 0 0 1 1 91
0f 000 00 0 0 0 0 0 1 1 99
10 0FF 0F 1 1 0 1 0 1 1 A1
11 0FF 0F 1 1 0 1 0 1 1 A9
12 0FF 0F 1 1 0 1 0 1 1 B1
13 0FF 0F 1 1 0 1 0 1 1 B9
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 2
IRQ1 -> 1
IRQ3 -> 3
IRQ4 -> 4
IRQ5 -> 18
IRQ6 -> 6
IRQ7 -> 7
IRQ8 -> 8
IRQ9 -> 19
IRQ10 -> 17
IRQ11 -> 16
IRQ12 -> 12
IRQ14 -> 14
IRQ15 -> 15
.................................... done.
checking TSC synchronization across CPUs: passed.
PCI: PCI BIOS revision 2.10 entry at 0xf0730, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 262144 bhash 65536)
Initializing RT netlink socket
Starting kswapd v 1.5
vesafb: framebuffer at 0xe3000000, mapped to 0xd0009000, size 16384k
vesafb: mode is 800x600x16, linelength=1600, pages=16
vesafb: protected mode interface info at c000:043c
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
Detected PS/2 Mouse Port.
Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.13)
apm: disabled - APM is not SMP safe.
Real Time Clock Driver v1.09
RAM disk driver initialized: 16 RAM disks of 4096K size
Uniform Multi-Platform E-IDE driver Revision: 6.30
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 21
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:pio
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
raid5: measuring checksumming speed
raid5: MMX detected, trying high-speed MMX checksum routines
pII_mmx : 907.161 MB/sec
p5_mmx : 923.925 MB/sec
8regs : 695.706 MB/sec
32regs : 410.718 MB/sec
using fastest function: p5_mmx (923.925 MB/sec)
scsi : 0 hosts.
scsi : detected total.
md.c: sizeof(mdp_super_t) = 4096
Partition check:
RAMDISK: Compressed image found at block 0
autodetecting RAID arrays
autorun ...
... autorun DONE.
VFS: Mounted root (ext2 filesystem).
scsi0 : AdvanSys SCSI 3.2M: PCI Ultra-Wide: BIOS CC000/7FFF, IO B400/3F, IRQ 10
scsi1 : AdvanSys SCSI 3.2M: PCI Ultra-Wide: BIOS D0000/7FFF, IO B000/3F, IRQ 11
scsi : 2 hosts.
Vendor: IBM Model: DNES-309170 Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
Vendor: PIONEER Model: CD-ROM DR-U12X Rev: 1.06
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 2, lun 0
Vendor: HP Model: CD-Writer+ 9200 Rev: 1.0c
Type: CD-ROM ANSI SCSI revision: 04
Detected scsi CD-ROM sr1 at scsi0, channel 0, id 3, lun 0
Vendor: IBM Model: DNES-309170 Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Detected scsi disk sdb at scsi0, channel 0, id 4, lun 0
Vendor: HP Model: C1533A Rev: A812
Type: Sequential-Access ANSI SCSI revision: 02
Vendor: IBM Model: DNES-309170 Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Detected scsi disk sdc at scsi0, channel 0, id 6, lun 0
Vendor: UMAX Model: Astra 2400S Rev: V1.1
Type: Scanner ANSI SCSI revision: 02
sr0: scsi3-mmc drive: 12x/12x xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.11
sr1: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
SCSI device sda: hdwr sector= 512 bytes. Sectors= 17916240 [8748 MB] [8.7 GB]
sda: sda1 sda2 < sda5 sda6 sda7 sda8 >
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 17916240 [8748 MB] [8.7 GB]
sdb: sdb1
SCSI device sdc: hdwr sector= 512 bytes. Sectors= 17916240 [8748 MB] [8.7 GB]
sdc: sdc1
autodetecting RAID arrays
autorun ...
... autorun DONE.
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 140k freed
Adding Swap: 248968k swap-space (priority -1)
st: bufsize 32768, wrt 30720, max buffers 5, s/g segs 16.
Detected scsi tape st0 at scsi0, channel 0, id 5, lun 0
es1371: version v0.22 time 13:08:57 Oct 5 2000
es1371: found chip, vendor id 0x1274 device id 0x1371 revision 0x06
es1371: found es1371 rev 6 at io 0xd000 irq 9
es1371: features: joystick 0x0
es1371: codec vendor TRA (0x545241) revision 35 (0x23)
es1371: codec features none
es1371: stereo enhancement: no 3D stereo enhancement
ne2k-pci.c:vpre-1.00e 5/27/99 D. Becker/P. Gortmaker
http://cesdis.gsfc.nasa.gov/linux/drivers/ne2k-pci.html
ne2k-pci.c: PCI NE2000 clone 'RealTek RTL-8029' at I/O 0xb800, IRQ 5.
eth0: RealTek RTL-8029 found at 0xb800, IRQ 5, 00:80:C8:FC:84:11.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.232 $ time 13:09:24 Oct 5 2000
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: Intel USB controller: setting latency timer to 0
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
usb.c: USB new device connect, assigned device number 1
hub.c: USB hub found
hub.c: 2 ports detected
parport0: PC-style at 0x378 (0x778) [SPP,ECP,ECPEPP,ECPPS2]
parport0: detected irq 7; use procfs to enable interrupt-driven operation.
parport_probe: succeeded
parport0: Printer, HEWLETT-PACKARD DESKJET 660C
lp0: using parport0 (polling).
AdvanSys SCSI 3.2M: PCI Ultra-Wide: BIOS CC000/7FFF, IO B400/3F, IRQ 10
ROM BIOS Version: 3.1I
Device Information for AdvanSys SCSI Host 0:
Target IDs Detected: 0, 2, 3, 4, 5, 6, 7, (7=Host Adapter)
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: IBM Model: DNES-309170 Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi0 Channel: 00 Id: 02 Lun: 00
Vendor: PIONEER Model: CD-ROM DR-U12X Rev: 1.06
Type: CD-ROM ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 03 Lun: 00
Vendor: HP Model: CD-Writer+ 9200 Rev: 1.0c
Type: CD-ROM ANSI SCSI revision: 04
Host: scsi0 Channel: 00 Id: 04 Lun: 00
Vendor: IBM Model: DNES-309170 Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi0 Channel: 00 Id: 05 Lun: 00
Vendor: HP Model: C1533A Rev: A812
Type: Sequential-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 06 Lun: 00
Vendor: IBM Model: DNES-309170 Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
EEPROM Settings for AdvanSys SCSI Host 0:
Serial Number: AA48A919D407
Host SCSI ID: 7, Host Queue Size: 253, Device Queue Size: 63
termination: 0 (Automatic), bios_ctrl: ffe7
Target ID: 0 1 2 3 4 5 6 7 8 9 A B C D E F
Disconnects: Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Command Queuing: Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Start Motor: Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Synchronous Transfer: Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Ultra Transfer: Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Wide Transfer: Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Linux Driver Configuration and Information for AdvanSys SCSI Host 0:
host_busy 0, last_reset 0, max_id 16, max_lun 8, max_channel 0
unique_id 0, can_queue 253, this_id 7, sg_tablesize 255, cmd_per_lun 1
unchecked_isa_dma 0, use_clustering 1, loaded_as_module 1
flags c, last_reset 0, jiffies b51d
queue_depth: 0:63 2:63 3:63 4:63 5:63 6:63
Linux Driver Statistics for AdvanSys SCSI Host 0:
command 0, queuecommand 8690, abort 0, reset 0, biosparam 0
interrupt 8675, callback 8690, done 8690
exe_noerror 8690, exe_busy 0, exe_error 0, exe_unknown 0
build_error 0, build_noreq 0, build_nosg 0
cont_cnt 5160, cont_xfer 15486.5 kb avg_xfer 3.0 kb
sg_cnt 3530, sg_elem 21525, sg_xfer 83869.0 kb
avg_num_elem 6.0, avg_elem_size 3.8 kb, avg_xfer_size 23.7 kb
Active and Waiting Request Queues (Time Unit: 100 HZ):
target 0
active: cnt [cur 0, max 63, tot 8375], time [min 0, max 75, avg 4.0]
waiting: cnt [cur 0, max 0, tot 0], time [min 0, max 0, avg 0.0]
target 2
active: cnt [cur 0, max 1, tot 3], time [min 0, max 0, avg 0.0]
waiting: cnt [cur 0, max 0, tot 0], time [min 0, max 0, avg 0.0]
target 3
active: cnt [cur 0, max 1, tot 3], time [min 0, max 1, avg 0.6]
waiting: cnt [cur 0, max 0, tot 0], time [min 0, max 0, avg 0.0]
target 4
active: cnt [cur 0, max 1, tot 149], time [min 0, max 13, avg 0.8]
waiting: cnt [cur 0, max 0, tot 0], time [min 0, max 0, avg 0.0]
target 5
active: cnt [cur 0, max 1, tot 2], time [min 0, max 1, avg 0.5]
waiting: cnt [cur 0, max 0, tot 0], time [min 0, max 0, avg 0.0]
target 6
active: cnt [cur 0, max 1, tot 149], time [min 0, max 13, avg 0.7]
waiting: cnt [cur 0, max 0, tot 0], time [min 0, max 0, avg 0.0]
Adv Library Configuration and Statistics for AdvanSys SCSI Host 0:
iop_base d101f000, cable_detect: 1, err_code 0
chip_version 64, lib_version 505, mcode_date 136a, mcode_version 505
Queuing Enabled: 0:Y 2:N 3:N 4:Y 5:N 6:Y
Queue Limit: 0:63 2:1 3:1 4:63 5:1 6:63
Command Pending: 0:0 2:0 3:0 4:0 5:0 6:0
Wide Enabled: 0:N 2:N 3:N 4:N 5:N 6:N
Transfer Bit Width: 0:8 2:8 3:8 4:8 5:8 6:8
Synchronous Enabled: 0:Y 2:Y 3:Y 4:Y 5:Y 6:Y
0: Transfer Period Factor: 12 (20.8 Mhz), REQ/ACK Offset: 15
2: Transfer Period Factor: 25 (10.0 Mhz), REQ/ACK Offset: 15
3: Transfer Period Factor: 25 (10.0 Mhz), REQ/ACK Offset: 15
4: Transfer Period Factor: 12 (20.8 Mhz), REQ/ACK Offset: 15
5: Transfer Period Factor: 25 (10.0 Mhz), REQ/ACK Offset: 15
6: Transfer Period Factor: 12 (20.8 Mhz), REQ/ACK Offset: 15
AdvanSys SCSI 3.2M: PCI Ultra-Wide: BIOS D0000/7FFF, IO B000/3F, IRQ 11
ROM BIOS Version: 3.1I
Device Information for AdvanSys SCSI Host 1:
Target IDs Detected: 1, 7, (7=Host Adapter)
Host: scsi1 Channel: 00 Id: 01 Lun: 00
Vendor: UMAX Model: Astra 2400S Rev: V1.1
Type: Scanner ANSI SCSI revision: 02
EEPROM Settings for AdvanSys SCSI Host 1:
Serial Number: AA48A919D387
Host SCSI ID: 7, Host Queue Size: 253, Device Queue Size: 63
termination: 0 (Automatic), bios_ctrl: ffe7
Target ID: 0 1 2 3 4 5 6 7 8 9 A B C D E F
Disconnects: Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Command Queuing: Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Start Motor: Y N Y Y Y N Y Y Y Y Y Y Y Y Y Y
Synchronous Transfer: Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Ultra Transfer: Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Wide Transfer: Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Linux Driver Configuration and Information for AdvanSys SCSI Host 1:
host_busy 0, last_reset 0, max_id 16, max_lun 8, max_channel 0
unique_id 0, can_queue 253, this_id 7, sg_tablesize 255, cmd_per_lun 1
unchecked_isa_dma 0, use_clustering 1, loaded_as_module 1
flags c, last_reset 0, jiffies 80a1
queue_depth: 1:63
Linux Driver Statistics for AdvanSys SCSI Host 1:
command 0, queuecommand 16, abort 0, reset 0, biosparam 0
interrupt 16, callback 16, done 16
exe_noerror 16, exe_busy 0, exe_error 0, exe_unknown 0
build_error 0, build_noreq 0, build_nosg 0
cont_cnt 16, cont_xfer 8.0 kb avg_xfer 0.5 kb
Active and Waiting Request Queues (Time Unit: 100 HZ):
target 1
active: cnt [cur 0, max 1, tot 2], time [min 0, max 4, avg 2.0]
waiting: cnt [cur 0, max 0, tot 0], time [min 0, max 0, avg 0.0]
Adv Library Configuration and Statistics for AdvanSys SCSI Host 1:
iop_base d0020000, cable_detect: 3, err_code 0
chip_version 64, lib_version 505, mcode_date 136a, mcode_version 505
Queuing Enabled: 1:N
Queue Limit: 1:1
Command Pending: 1:0
Wide Enabled: 1:N
Transfer Bit Width: 1:8
Synchronous Enabled: 1:N
AdvanSys SCSI 3.2M: PCI Ultra-Wide: BIOS D0000/7FFF, IO B000/3F, IRQ 11
ROM BIOS Version: 3.1I
Device Information for AdvanSys SCSI Host 1:
Target IDs Detected: 1, 7, (7=Host Adapter)
Host: scsi1 Channel: 00 Id: 01 Lun: 00
Vendor: UMAX Model: Astra 2400S Rev: V1.1
Type: Scanner ANSI SCSI revision: 02
EEPROM Settings for AdvanSys SCSI Host 1:
Serial Number: AA48A919D387
Host SCSI ID: 7, Host Queue Size: 253, Device Queue Size: 63
termination: 0 (Automatic), bios_ctrl: ffe7
Target ID: 0 1 2 3 4 5 6 7 8 9 A B C D E F
Disconnects: Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Command Queuing: Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Start Motor: Y N Y Y Y N Y Y Y Y Y Y Y Y Y Y
Synchronous Transfer: Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Ultra Transfer: Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Wide Transfer: Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y
Linux Driver Configuration and Information for AdvanSys SCSI Host 1:
host_busy 0, last_reset 0, max_id 16, max_lun 8, max_channel 0
unique_id 0, can_queue 253, this_id 7, sg_tablesize 255, cmd_per_lun 1
unchecked_isa_dma 0, use_clustering 1, loaded_as_module 1
flags c, last_reset 0, jiffies b8d5
queue_depth: 1:63
Linux Driver Statistics for AdvanSys SCSI Host 1:
command 0, queuecommand 16, abort 0, reset 0, biosparam 0
interrupt 16, callback 16, done 16
exe_noerror 16, exe_busy 0, exe_error 0, exe_unknown 0
build_error 0, build_noreq 0, build_nosg 0
cont_cnt 16, cont_xfer 8.0 kb avg_xfer 0.5 kb
Active and Waiting Request Queues (Time Unit: 100 HZ):
target 1
active: cnt [cur 0, max 1, tot 2], time [min 0, max 4, avg 2.0]
waiting: cnt [cur 0, max 0, tot 0], time [min 0, max 0, avg 0.0]
Adv Library Configuration and Statistics for AdvanSys SCSI Host 1:
iop_base d1021000, cable_detect: 3, err_code 0
chip_version 64, lib_version 505, mcode_date 136a, mcode_version 505
Queuing Enabled: 1:N
Queue Limit: 1:1
Command Pending: 1:0
Wide Enabled: 1:N
Transfer Bit Width: 1:8
Synchronous Enabled: 1:N
