This patch is actually deceptively simple for what it does.
For all fusion devices with integrated raid devices, we make the card
pretend it has two channels, then all I/O on channel 1 is directed to
the underlying physical discs of the integrated raid assembly. The net
effect is that all the physical discs show up correctly on virtual
channel 1 (we also specify no_uld_attach for anything on virtual channel
1 so that they can only be accessed using ioctls to the sg device).
The net effect is something like this:
mptbase: Initiating ioc22 bringup
ioc22: 53C1030: Capabilities={Initiator}
scsi27 : ioc22: LSI53C1030, FwRev=01032920h, Ports=1, MaxQ=222, IRQ=57
Vendor: LSILOGIC Model: 1030 IM Rev: 1000
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 17813504 512-byte hdwr sectors (9121 MB)
SCSI device sdb: drive cache: write through
SCSI device sdb: 17813504 512-byte hdwr sectors (9121 MB)
SCSI device sdb: drive cache: write through
sdb: unknown partition table
Attached scsi disk sdb at scsi27, channel 0, id 0, lun 0
Attached scsi generic sg1 at scsi27, channel 0, id 0, lun 0, type 0
Vendor: QUANTUM Model: ATLAS IV 9 WLS Rev: 0B0B
Type: Direct-Access ANSI SCSI revision: 03
Attached scsi generic sg2 at scsi27, channel 1, id 0, lun 0, type 0
Vendor: QUANTUM Model: ATLAS IV 9 WLS Rev: 0B0B
Type: Direct-Access ANSI SCSI revision: 03
Attached scsi generic sg3 at scsi27, channel 1, id 1, lun 0, type 0
where you can see that sdb is the RAID device and sg2 and sg3 the
underlying SCSI discs.
James
diff --git a/drivers/message/fusion/mptscsih.c
b/drivers/message/fusion/mptscsih.c
--- a/drivers/message/fusion/mptscsih.c
+++ b/drivers/message/fusion/mptscsih.c
@@ -171,6 +171,7 @@ static void mptscsih_fillbuf(char *buffe
void mptscsih_remove(struct pci_dev *);
void mptscsih_shutdown(struct pci_dev *);
+static int mptscsih_is_raid_volume(MPT_SCSI_HOST *hd, uint id);
#ifdef CONFIG_PM
int mptscsih_suspend(struct pci_dev *pdev, pm_message_t state);
int mptscsih_resume(struct pci_dev *pdev);
@@ -1274,6 +1275,12 @@ mptscsih_qcmd(struct scsi_cmnd *SCpnt, v
return SCSI_MLQUEUE_HOST_BUSY;
}
+ if (SCpnt->device->channel && !mptscsih_is_raid_volume(hd, target)) {
+ SCpnt->result = DID_NO_CONNECT << 16;
+ done(SCpnt);
+ return 0;
+ }
+
/*
* Put together a MPT SCSI request...
*/
@@ -1318,9 +1325,12 @@ mptscsih_qcmd(struct scsi_cmnd *SCpnt, v
/* Use the above information to set up the message frame
*/
pScsiReq->TargetID = (u8) target;
- pScsiReq->Bus = (u8) SCpnt->device->channel;
+ pScsiReq->Bus = 0;
pScsiReq->ChainOffset = 0;
- pScsiReq->Function = MPI_FUNCTION_SCSI_IO_REQUEST;
+ if (SCpnt->device->channel)
+ pScsiReq->Function = MPI_FUNCTION_RAID_SCSI_IO_PASSTHROUGH;
+ else
+ pScsiReq->Function = MPI_FUNCTION_SCSI_IO_REQUEST;
pScsiReq->CDBLength = SCpnt->cmd_len;
pScsiReq->SenseBufferLength = MPT_SENSE_BUFFER_SIZE;
pScsiReq->Reserved = 0;
@@ -2145,6 +2155,9 @@ mptscsih_slave_alloc(struct scsi_device
if (hd == NULL)
return -ENODEV;
+ if (device->channel)
+ device->no_uld_attach = 1;
+
if ((vdev = hd->Targets[target]) != NULL)
goto out;
diff --git a/drivers/message/fusion/mptspi.c b/drivers/message/fusion/mptspi.c
--- a/drivers/message/fusion/mptspi.c
+++ b/drivers/message/fusion/mptspi.c
@@ -237,7 +237,10 @@ mptspi_probe(struct pci_dev *pdev, const
sh->max_id = MPT_MAX_SCSI_DEVICES;
sh->max_lun = MPT_LAST_LUN + 1;
- sh->max_channel = 0;
+ if (ioc->spi_data.isRaid)
+ sh->max_channel = 1;
+ else
+ sh->max_channel = 0;
sh->this_id = ioc->pfacts[0].PortSCSIID;
/* Required entry.
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
