On Tue, 09 Aug 2005 11:55:36 -0500, James Bottomley wrote: > On Tue, 2005-08-09 at 07:59 -0700, Martin J. Bligh wrote: >> Dear novice test examiner, >> >> It's in http://test.kernel.org with everything else ;-) >> 2.6.13-rc4-mm1+jejb_fix ... drills down to: >> >> http://test.kernel.org/10080/debug/console.log > > Well, OK, apparently some novice coder made an error converting from a > stack allocated buffer to a kmalloc'd one in the sense handling > routines. > > I think this patch should fix it (or at least restore it to the level of > bugginess it had before). > > James > > diff --git a/drivers/scsi/scsi_lib.c b/drivers/scsi/scsi_lib.c > --- a/drivers/scsi/scsi_lib.c > +++ b/drivers/scsi/scsi_lib.c > @@ -342,12 +342,12 @@ int scsi_execute_req(struct scsi_device > sense = kmalloc(SCSI_SENSE_BUFFERSIZE, GFP_KERNEL); > if (!sense) > return DRIVER_ERROR << 24; > - memset(sense, 0, sizeof(*sense)); > + memset(sense, 0, SCSI_SENSE_BUFFERSIZE); > } > result = scsi_execute(sdev, cmd, data_direction, buffer, bufflen, > sense, timeout, retries, 0); > if (sshdr) > - scsi_normalize_sense(sense, sizeof(*sense), sshdr); > + scsi_normalize_sense(sense, SCSI_SENSE_BUFFERSIZE, sshdr); > > kfree(sense); > return result; > >
I tired kernel-2.6.13-rc-6-mm1 which has this patch and i still get the speed drop due to Domain Validation detected failure. I am using a LSIU160/Symbios 53c1010 Ultra3 scsi adapter and it works at full speed (75 MB/sec) with kernel-2.6.12. And dmesg shows: kernel: target0:0:0: Beginning Domain Validation kernel: target0:0:0: asynchronous. kernel: WIDTH IS 1 kernel: target0:0:0: wide asynchronous. kernel: target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62) kernel: target0:0:0: Ending Domain Validation kernel: sym1: <1010-33> rev 0x1 at pci 0000:01:07.1 irq 11 kernel: sym1: Symbios NVRAM, ID 7, Fast-80, SE, parity checking kernel: sym1: open drain IRQ line driver kernel: sym1: using LOAD/STORE-based firmware. kernel: sym1: handling phase mismatch from SCRIPTS. kernel: sym1: SCSI BUS has been reset. kernel: scsi1 : sym-2.2.0 kernel: libata version 1.11 loaded. With kernel-2.6.13-rc6-mm1 the speed drops back to 2.70 MB/sec because of validation failure and dmesg shows: kernel: target0:0:0: Beginning Domain Validation kernel: target0:0:0: asynchronous. kernel: target0:0:0: wide asynchronous. kernel: target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT IU QAS ( kernel: sym0: unexpected disconnect kernel: target0:0:0: Write Buffer failure 700ff kernel: target0:0:0: Domain Validation Disabing Information units kernel: 0:0:0:0: phase change 6-7 [EMAIL PROTECTED] resid=10. kernel: target0:0:0: asynchronous. kernel: sym0: unexpected disconnect target0:0:0: Write Buffer failure 700ff target0:0:0: Domain Validation detected failure, dropping back kernel: target0:0:0: asynchronous. target0:0:0: Ending Domain Validation kernel: sym1: <1010-33> rev 0x1 at pci 0000:01:07.1 irq 11 kernel: sym1: Symbios NVRAM, ID 7, Fast-80, SE, parity checkingkernel: sym1: open drain IRQ line driver, using on-chip SRAM kernel: sym1: using LOAD/STORE-based firmware. kernel: sym1: handling phase mismatch from SCRIPTS. kernel: sym1: SCSI BUS has been reset. kernel: scsi1 : sym-2.2.1 kernel: libata version 1.11 loaded. The kernel config has: CONFIG_SCSI_SYM53C8XX_2=y CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1 CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16 CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64 # CONFIG_SCSI_SYM53C8XX_IOMAPPED is not set - To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html
