Richard A Lary wrote:
> From: Richard Lary <[EMAIL PROTECTED]>
>
> This patch fixes Segmemtation fault which occurs when executing:
> #udevinfo -a -p /sys/class/scsi_host/{qla2xxx_host}
>
> The qla2xxx driver ignores the size and offset parameters when
> reading nvram and vpd attributes.
Thank you for finding the problem.
Please find comments below.
Updated patch will be followed, soon.
Thank you,
Seokmann
> Signed-off-by: Richard Lary <[EMAIL PROTECTED]>
> ---
>
> Example:
>
> looking at device '/class/scsi_host/host5':
> KERNEL=="host5"
> SUBSYSTEM=="scsi_host"
> SYSFS{proc_name}=="_NULL_"
> SYSFS{unchecked_isa_dma}=="0"
> SYSFS{sg_tablesize}=="255"
> SYSFS{cmd_per_lun}=="3"
> SYSFS{host_busy}=="0"
> SYSFS{unique_id}=="0"
> SYSFS{beacon}=="Disabled"
> SYSFS{zio_timer}=="200 us"
> SYSFS{zio}=="Disabled"
> SYSFS{state}=="Link Up - F_Port"
> SYSFS{pci_info}=="PCI-X Mode 1 _100 MHz_"
> SYSFS{model_desc}=="IBM eServer BC 4Gb FC Expansion Card SFF"
> SYSFS{model_name}=="QMC2462S"
> SYSFS{isp_id}=="0000 0000 0000 0000"
> SYSFS{isp_name}=="ISP2422"
> SYSFS{serial_num}=="N83786"
> SYSFS{fw_version}=="4.00.26 _IP_ "
> SYSFS{driver_version}=="8.01.07-k3-rl"
>
> looking at device '/devices/pci0000:00/0000:00:01.0/0000:01:02.0/host5':
> ID=="host5"
> BUS==""
> DRIVER==""
> SYSFS{sfp}==""
> Segmentation fault
>
> Applies to: scsi-misc-2.6.git
>
> Index: b/drivers/scsi/qla2xxx/qla_attr.c
> ===================================================================
> --- a/drivers/scsi/qla2xxx/qla_attr.c
> +++ b/drivers/scsi/qla2xxx/qla_attr.c
> @@ -87,17 +87,35 @@ qla2x00_sysfs_read_nvram(struct kobject
> struct scsi_qla_host *ha = to_qla_host(dev_to_shost(container_of(kobj,
> struct device, kobj)));
> unsigned long flags;
> + int size = ha->nvram_size;
> + char *nvram_buf;
>
> - if (!capable(CAP_SYS_ADMIN) || off != 0)
> + if (!capable(CAP_SYS_ADMIN) || off > size)
> return 0;
>
> + nvram_buf = (char *)vmalloc(size);
> + if (nvram_buf == NULL) {
> + qla_printk(KERN_WARNING, ha,
> + "Unable to allocate memory for nvram retrieval "
> + "(%x).\n", size);
> +
> + return 0;
> + }
IMO, as given buf is valid address which can be accessed by the driver, extra
vmalloc() is not necessary.
> +
> + if (off + count > size) {
> + size -= off;
> + count = size;
> + }
Before this check, it would be good to check 'if count == 0' and return 0.
> +
> /* Read NVRAM. */
> spin_lock_irqsave(&ha->hardware_lock, flags);
> - ha->isp_ops.read_nvram(ha, (uint8_t *)buf, ha->nvram_base,
> - ha->nvram_size);
> + ha->isp_ops.read_nvram(ha, (uint8_t *)nvram_buf, ha->nvram_base, size);
> spin_unlock_irqrestore(&ha->hardware_lock, flags);
>
> - return ha->nvram_size;
> + memcpy(buf, &nvram_buf[off], count);
> +
> + vfree(nvram_buf);
As vmalloc(), memcpy() and vfree() also are not necessary.
> + return count;
> }
>
> static ssize_t
> @@ -292,16 +310,35 @@ qla2x00_sysfs_read_vpd(struct kobject *k
> struct scsi_qla_host *ha = to_qla_host(dev_to_shost(container_of(kobj,
> struct device, kobj)));
> unsigned long flags;
> + int size = ha->vpd_size;
> + char *vpd_buf;
>
> - if (!capable(CAP_SYS_ADMIN) || off != 0)
> + if (!capable(CAP_SYS_ADMIN) || off > size)
> return 0;
Also, check if count == 0 and return 0 if so.
> + vpd_buf = (char *)vmalloc(size);
> + if (vpd_buf == NULL) {
> + qla_printk(KERN_WARNING, ha,
> + "Unable to allocate memory for vpd retrieval "
> + "(%x).\n", size);
> +
> + return 0;
> + }
Same here, extra memory allocation is not required.
> + if (off + count > size) {
> + size -= off;
> + count = size;
> + }
>
> /* Read NVRAM. */
> spin_lock_irqsave(&ha->hardware_lock, flags);
> - ha->isp_ops.read_nvram(ha, (uint8_t *)buf, ha->vpd_base, ha->vpd_size);
> + ha->isp_ops.read_nvram(ha, (uint8_t *)vpd_buf, ha->vpd_base, size);
> spin_unlock_irqrestore(&ha->hardware_lock, flags);
>
> - return ha->vpd_size;
> + memcpy(buf, &vpd_buf[off], count);
> +
> + vfree(vpd_buf);
Same here, as vmalloc(), memcpy() and vfree() are not necessary.
> + return count;
> }
>
> static ssize_t
>
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
> the body of a message to [EMAIL PROTECTED]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
