On 1/26/19 2:18 AM, James Smart wrote:
Now that the lower half has much better per-cpu parallelization
using the hardware queues, the SCSI MQ support needs to be tied
into it.
The involves the following mods:
- Use the hardware queue info from the midlayer to help select the
hardware queue to utilize. This required change to the
get_scsi-buf_xxx routines.
= Remove lpfc_sli4_scmd_to_wqidx_distr() routine. No longer needed.
- Includes fix for SLI-3 that does not have multi queue parallelization.
Signed-off-by: Dick Kennedy <[email protected]>
Signed-off-by: James Smart <[email protected]>
---
v2:
Adapt for 5.0 api changes:
SCSI mq support only.
Remove all use of shost_use_scsi_mq().
Remove driver flag and module parameter to enable scsi_mq
---
drivers/scsi/lpfc/lpfc.h | 3 +-
drivers/scsi/lpfc/lpfc_init.c | 5 +--
drivers/scsi/lpfc/lpfc_scsi.c | 72 ++++++++++++-------------------------------
drivers/scsi/lpfc/lpfc_scsi.h | 2 --
4 files changed, 24 insertions(+), 58 deletions(-)
diff --git a/drivers/scsi/lpfc/lpfc.h b/drivers/scsi/lpfc/lpfc.h
index 9262c52e32d6..755bf49c272c 100644
--- a/drivers/scsi/lpfc/lpfc.h
+++ b/drivers/scsi/lpfc/lpfc.h
@@ -619,7 +619,8 @@ struct lpfc_ras_fwlog {
struct lpfc_hba {
/* SCSI interface function jump table entries */
struct lpfc_scsi_buf * (*lpfc_get_scsi_buf)
- (struct lpfc_hba *, struct lpfc_nodelist *);
+ (struct lpfc_hba *phba, struct lpfc_nodelist *ndlp,
+ struct scsi_cmnd *cmnd);
int (*lpfc_scsi_prep_dma_buf)
(struct lpfc_hba *, struct lpfc_scsi_buf *);
void (*lpfc_scsi_unprep_dma_buf)
diff --git a/drivers/scsi/lpfc/lpfc_init.c b/drivers/scsi/lpfc/lpfc_init.c
index 36d9c32c9c87..e4040cdd76b7 100644
--- a/drivers/scsi/lpfc/lpfc_init.c
+++ b/drivers/scsi/lpfc/lpfc_init.c
@@ -4063,12 +4063,13 @@ lpfc_create_port(struct lpfc_hba *phba, int instance,
struct device *dev)
shost->max_lun = vport->cfg_max_luns;
shost->this_id = -1;
shost->max_cmd_len = 16;
- shost->nr_hw_queues = phba->cfg_hdw_queue;
if (phba->sli_rev == LPFC_SLI_REV4) {
+ shost->nr_hw_queues = phba->cfg_hdw_queue;
shost->dma_boundary =
phba->sli4_hba.pc_sli4_params.sge_supp_len-1;
shost->sg_tablesize = phba->cfg_scsi_seg_cnt;
- }
+ } else
+ shost->nr_hw_queues = 1;
/*
* Set initial can_queue value since 0 is no longer supported and
Why do you restrict full mq support to SLE-4?
The original code seems to imply that older revisions would be able to
do mq, too...
Can you add a comment here why older revisions don't support it?
Other than that:
Reviewed-by: Hannes Reinecke <[email protected]>
Cheers,
Hannes
