Hello Gerard , Please find below a dmesg from a very bad tar
attempt to the tape drive mentioned . Also I tried the 8500
everything else same except used 8500 instead . IE:
Vendor: EXABYTE Model: EXB-850085QANXRC Rev: 06X0
Type: Sequential-Access ANSI SCSI revision: 02
Command used :
tar --same-owner -cpf /dev/st0 /etc/passwd /[0-9A-Za-oq-z]*
a few minutes after the 'command processing resumed'
the timeouts resumed & didn't stop , truth be told couldn't
be stopped with out 'reset switch' . :-{
Tia, JimL
+-----------------------------------------------------------------------+
| James W. Laferriere - Network Engineer - [EMAIL PROTECTED] |
| System Techniques - 25416 - 22nd S. - Des-Moines, WA 98198 |
| Give me VMS -or- Give me Linux -but- only on AXP |
+-----------------------------------------------------------------------+
Memory: sized by int13 0e801h
Console: 16 point font, 400 scans
Console: colour VGA+ 80x25, 1 virtual console (max 63)
pcibios_init : BIOS32 Service Directory structure at 0x000fabf0
pcibios_init : BIOS32 Service Directory entry at 0xfb0b0
pcibios_init : PCI BIOS revision 2.10 entry at 0xfb0e0
Probing PCI hardware.
Calibrating delay loop.. ok - 179.40 BogoMIPS
Memory: 127664k/131072k available (876k kernel code, 384k reserved, 2148k data)
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.13 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: IGMP, ICMP, UDP, TCP, IPIP
Linux IP multicast router 0.07.
Checking 386/387 coupling... Ok, fpu using exception 16 error reporting.
Checking 'hlt' instruction... Ok.
Linux version 2.0.36 (root@filesrv1) (gcc version 2.7.2.3) #1 Sun Dec 20 23:38:07 PST
1998
Starting kswapd v 1.4.2.2
Serial driver version 4.13p with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
lp1 at 0x0378, (polling)
Ramdisk driver initialized : 16 ramdisks of 4096K size
ide: i82371 PIIX (Triton) on PCI bus 0 function 57
ide: ports are not enabled (BIOS)
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.36.3 MAX_MD_DEV=4, MAX_REAL=8
linear personality registered
raid0 personality registered
raid1 personality registered
raid5 personality registered
ncr53c8xx: at PCI bus 0, device 19, function 0
ncr53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
ncr53c8xx: 53c810a detected
ncr53c8xx: at PCI bus 0, device 20, function 0
ncr53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
ncr53c8xx: 53c875J detected with Symbios NVRAM
ncr53c875J-0: rev=0x04, base=0xf1102000, io_port=0x6200, irq=9
ncr53c875J-0: Symbios format NVRAM, ID 7, Fast-20, Parity Checking
ncr53c875J-0: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 05/4e/80/01/00/24
ncr53c875J-0: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 05/46/80/00/08/24
ncr53c875J-0: on-chip RAM at 0xf1103000
ncr53c875J-0: requesting shared irq 9 (dev_id=0x3fe000)
ncr53c875J-0: resetting, command processing suspended for 2 seconds
ncr53c875J-0: restart (scsi reset).
ncr53c875J-0: enabling clock multiplier
ncr53c875J-0: Downloading SCSI SCRIPTS.
ncr53c810a-1: rev=0x12, base=0xf1101000, io_port=0x6100, irq=9
ncr53c810a-1: ID 7, Fast-10, Parity Checking
ncr53c810a-1: restart (scsi reset).
scsi0 : sym53c8xx/version 1.0
scsi1 : sym53c8xx/version 1.0
scsi : 2 hosts.
ncr53c875J-0: command processing resumed
Vendor: Quantum Model: XP31070W Rev: L912
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
Vendor: QUANTUM Model: FIREBALL_TM2110S Rev: 300X
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
ncr53c875J-0-<0,0>: tagged command queue depth set to 8
ncr53c875J-0-<1,0>: tagged command queue depth set to 8
Vendor: EXABYTE Model: EXB-8200 Rev: 262Z
Type: Sequential-Access ANSI SCSI revision: 01
Detected scsi tape st0 at scsi1, channel 0, id 4, lun 0
Vendor: PIONEER Model: CD-ROM DR-124X Rev: 1.06
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi1, channel 0, id 6, lun 0
scsi : detected 1 SCSI tape 1 SCSI cdrom 2 SCSI disks total.
ncr53c875J-0-<0,*>: WIDE SCSI (16 bit) enabled.
ncr53c875J-0-<0,*>: FAST-10 WIDE SCSI 20.0 MB/s (100 ns, offset 15)
SCSI device sda: hdwr sector= 512 bytes. Sectors= 2203480 [1075 MB] [1.1 GB]
ncr53c875J-0-<1,*>: FAST-20 SCSI 20.0 MB/s (50 ns, offset 15)
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 4124736 [2014 MB] [2.0 GB]
tunnel: version v0.2b2
PPP: version 2.2.0 (dynamic channel allocation)
TCP compression code copyright 1989 Regents of the University of California
PPP Dynamic channel allocation code copyright 1995 Caldera, Inc.
PPP line discipline registered.
eepro100.c:v1.05 10/16/98 Donald Becker
http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html
eth0: Intel EtherExpress Pro 10/100 at 0x6000, 00:A0:C9:2B:E5:5D, IRQ 10.
Board assembly 352509-003, Physical connectors present: RJ45
Primary interface chip DP83840 PHY #1.
DP83840 specific setup, setting register 23 to 8462.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x49caa8d6).
Receiver lock-up workaround activated.
eepro100.c:v1.05 10/16/98 Donald Becker
http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html
Partition check:
sda: sda1 sda2
sdb: sdb1 sdb2
VFS: Mounted root (ext2 filesystem) readonly.
Adding Swap: 130748k swap-space (priority -1)
Adding Swap: 130748k swap-space (priority -2)
ncr53c810a-1-<4,*>: SYNC transfers not supported.
scsi : aborting command due to timeout : pid 9454, scsi0, channel 0, id 1, lun 0 Read
(6) 14 f2 2e 02 00
ncr53c8xx_abort: pid=9454 serial_number=9473 serial_number_at_timeout=9473
scsi : aborting command due to timeout : pid 9456, scsi0, channel 0, id 1, lun 0 Read
(6) 14 f2 44 18 00
ncr53c8xx_abort: pid=9456 serial_number=9475 serial_number_at_timeout=9475
scsi : aborting command due to timeout : pid 9457, scsi0, channel 0, id 1, lun 0 Read
(6) 14 f4 e4 2c 00
ncr53c8xx_abort: pid=9457 serial_number=9476 serial_number_at_timeout=9476
scsi : aborting command due to timeout : pid 9460, scsi0, channel 0, id 1, lun 0 Read
(6) 14 f5 10 0a 00
ncr53c8xx_abort: pid=9460 serial_number=9479 serial_number_at_timeout=9479
scsi : aborting command due to timeout : pid 9461, scsi0, channel 0, id 0, lun 0 Write
(6) 04 eb 98 06 00
ncr53c8xx_abort: pid=9461 serial_number=9480 serial_number_at_timeout=9480
SCSI host 0 abort (pid 9456) timed out - resetting
SCSI bus is being reset for host 0 channel 0.
ncr53c8xx_reset: pid=9456 reset_flags=2 serial_number=9475
serial_number_at_timeout=9475
ncr53c875J-0: resetting, command processing suspended for 2 seconds
ncr53c875J-0: restart (scsi reset).
ncr53c875J-0: enabling clock multiplier
ncr53c875J-0: Downloading SCSI SCRIPTS.
ncr53c875J-0: command processing resumed
ncr53c875J-0-<1,*>: FAST-20 SCSI 20.0 MB/s (50 ns, offset 15)
ncr53c875J-0-<0,*>: WIDE SCSI (16 bit) enabled.
ncr53c875J-0-<0,*>: FAST-10 WIDE SCSI 20.0 MB/s (100 ns, offset 15)
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to [EMAIL PROTECTED]
