Gr�goire FAVRE wrote:
>
> Hello,
>
> I have booted 2.3.16 with vga=normal and found the problem (2.3.13 and 2.3.15 also
> don't boot normal, but I didn't see anything, as I used vga=794 and nothing print).
>
> At boot:
>
> Partition check:
> sda: sda1 sda2 < sda5 >
> sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 >
> Found PIIX4 ACPI device at e400
> scsi: aborting command due to timeout : pid 36, scsi 0, channel 0, id 4, lun 0 0
> x28 00 00 70 84 4c 00 00 02 00
> SCSI host 0 abort (pid 36) timeout - reseting
> SCSI bus is being reset for host 0 channel 0.
> SCSI ... reseted...
> SCSI ...
>
> ad nauseam...
>
> The drive four is ultra2wide..., from 2.2.12:
>
> (scsi0) <Adaptec AIC-7890/1 Ultra2 SCSI host adapter> found at PCI 6/0
> (scsi0) Wide Channel, SCSI ID=7, 32/255 SCBs
> (scsi0) Downloading sequencer code... 374 instructions downloaded
> scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.19/3.2.4
> <Adaptec AIC-7890/1 Ultra2 SCSI host adapter>
> scsi : 1 host.
> (scsi0:0:0:0) Synchronous at 20.0 Mbyte/sec, offset 15.
> Vendor: QUANTUM Model: FIREBALL_TM3200S Rev: 300X
> Type: Direct-Access ANSI SCSI revision: 02
> Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
> (scsi0:0:1:0) Synchronous at 20.0 Mbyte/sec, offset 8.
> Vendor: PIONEER Model: DVD-ROM DVD-303 Rev: 1.09
> Type: CD-ROM ANSI SCSI revision: 02
> Detected scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0
> (scsi0:0:2:0) Synchronous at 16.0 Mbyte/sec, offset 16.
> Vendor: PIONEER Model: CD-ROM DR-U06S Rev: 1.05
> Type: CD-ROM ANSI SCSI revision: 02
> Detected scsi CD-ROM sr1 at scsi0, channel 0, id 2, lun 0
> (scsi0:0:3:0) Synchronous at 10.0 Mbyte/sec, offset 8.
> Vendor: PLEXTOR Model: CD-R PX-R820T Rev: 1.05
> Type: CD-ROM ANSI SCSI revision: 02
> Detected scsi CD-ROM sr2 at scsi0, channel 0, id 3, lun 0
> (scsi0:0:4:0) Synchronous at 80.0 Mbyte/sec, offset 15.
> Vendor: IBM Model: DDRS-39130D Rev: DC1B
> Type: Direct-Access ANSI SCSI revision: 02
> Detected scsi disk sdb at scsi0, channel 0, id 4, lun 0
> scsi : detected 3 SCSI cdroms 2 SCSI disks total.
> sr0: scsi3-mmc drive: 0x/0x cd/rw xa/form2 cdda tray
> Uniform CDROM driver Revision: 2.55
> sr1: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
> sr2: scsi3-mmc drive: 20x/20x writer cd/rw xa/form2 cdda tray
> SCSI device sda: hdwr sector= 512 bytes. Sectors= 6281856 [3067 MB] [3.1 GB]
> SCSI device sdb: hdwr sector= 512 bytes. Sectors= 17850000 [8715 MB] [8.7 GB]
> PCI latency timer (CFLT) is unreasonably low at 0. Setting to 32 clocks.
> eth0: Intel EtherExpress Pro 10/100 at 0xa800, 00:E0:18:90:14:C5, IRQ 14.
> Board assembly 668081-002, Physical connectors present: RJ45
> Primary interface chip i82555 PHY #1.
> General self-test: passed.
> Serial sub-system self-test: passed.
> Internal registers self-test: passed.
> ROM checksum self-test: passed (0x24c9f043).
> Receiver lock-up workaround activated.
> Partition check:
> sda: sda1 sda2 < sda5 >
> sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 >
> VFS: Mounted root (ext2 filesystem) readonly.
>
> And my system is RedHat 6.0.
Disabling ACPI allow me to boot (paartially: vesafb won't work...).
Please, don't cc to me: I am on the list...
Greg ICQ:16624071 mailto:[EMAIL PROTECTED]
''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
Gregoire Favre, Institut de Math�matique de l'Universite de Lausanne
+41216923573,+41763231357, http://www.unil.ch/ima/docs/Personnes/gfavre
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to [EMAIL PROTECTED]
