Linux-Setup Digest #323, Volume #20 Mon, 1 Jan 01 20:13:05 EST
Contents:
thoroughly hacked off with linux install (Phil)
StarOffice 5.2 & JRE 1.3 (J.W. Sargent)
Re: UDMA hard disk (Glitch)
Re: Support Maxtor G450 (Glitch)
Security...restricting user-access to home-dir + links ("Koen Van Impe")
Re: RPM Vs. Source Vs. Binary ??? (Colin Watson)
Re: RPM Vs. Source Vs. Binary ??? (Colin Watson)
Re: UDMA hard disk (Nader)
Re: qmail relay (Darren Wyn Rees)
Modem is "busy" - PCI IRQ Sharing problem (Nader)
Re: Support Maxtor G450 (James Rose)
Problems with DSL and WinLinux 2000 ("C.E. Logan")
----------------------------------------------------------------------------
From: [EMAIL PROTECTED] (Phil)
Subject: thoroughly hacked off with linux install
Date: Mon, 01 Jan 2001 23:21:16 GMT
I have recently installed susse 6.2 on a machine with 2x4gig drives, I
only used one drive for the installation. The install appeared to work
but when it rebooted at the end of the install failed to complete
with the following log messages:-
#############################################
Partition check:
hda:
hdb: hdb1 hdb2 hdb3
autodetecting RAID arrays
autorun ...
... autorun DONE.
attempt to access beyond end of device
03:46 rw=0, want=2, limit=0
dev 03:46 blksize 1024 blocknr=1 sector=2 size=1024 count=1
EXT2-fs: unable to read superblock
Invalid session number of type of track
attempt to access beyond of device
03:46 rw=0, want33, limit=0
dev 03:46 blksize 1024 blocknr=32 sector=64 size=1024 count=1
isofs_read_super: bread failed, dev 03:46, iso_blknum=16, block=32
Kernel Panic: VFS: Unable to mount root fs on 03:46
##############################################
I was installing susse 6.2 in desparation after my install of redhat 7
repeatedly failed to recognise my 3com ethernet card and then
subsequent installs just crashed completely at the "reading package
information" stage. I should add that i have previously had redhat 7.0
installed on this machine and working fine with networking fully
operating.
I am beginning to wonder if I have suspect hardware but the latest
susse install worked fine until the reboot. Until I started the
re-install last week the system had been operating fine for about the
last 6 months.
Hope someone can shed some light.
Cheers
Phil
------------------------------
From: J.W. Sargent <jwsarge(no-spam)@pacbell.net>
Subject: StarOffice 5.2 & JRE 1.3
Crossposted-To: comp.os.linux.help,comp.os.linux.misc
Date: Mon, 1 Jan 2001 15:41:15 -0800
Good afternoon and Happy New Year. I recently installed StarOffice 5.2 that
came on a Storm 2000 disk. After that I downloaded JRE 1.3 (tar ball) from
Sun's site and following their instructions set it up in /usr/local. When I
go to the Java bookmark in 5.2 as a user and point the Java set-up to
/usr/local/jre1.3 I get a msg that there is no java runtime enviroment. I
think this is so to some configuration issue that I'm not aware of. Any
assistance that anyone may be able to provide would be greatly appreciated.
System info:
Debian 2.2 w/2.2.18 - smp kernel
Regards.............................................John Sargent
--
To reply remove (no-spam) from my address
prior to hitting the send button.
------------------------------
Date: Mon, 01 Jan 2001 19:13:18 -0500
From: Glitch <[EMAIL PROTECTED]>
Subject: Re: UDMA hard disk
Liu Wu wrote:
>
> I have a UDMA hard disk. I do the steps according to linux howto.
> but I input the command line when installation
>
> "linux ide2=0xd800,0xdc02"
>
> it alawys give me the messages
>
> "Unknown option 'ide2=0xd800, 0sdc02'"
>
> it seems that it does not know this option yet. I don't know what's wrong. I
> just did what I am told by the linux howto. it doesn't work. the result is
> the installation cannot find my hard disk at all.
>
you either need to write it like this
linux ide2="0xd800, 0xdc02"
or like this
linux append="ide2=0xd800, 0xdc02"
I forget which but i'm pretty sure one of them is correct based on info
in the lilo.conf man page.
try them and i hope it helps.
------------------------------
Date: Mon, 01 Jan 2001 19:14:10 -0500
From: Glitch <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.hardware
Subject: Re: Support Maxtor G450
Harald Adams wrote:
>
> Hi,
> does anybody out there know, how I can setup which X server to support the
> new maxtor G450 graphic board under Suse 7.0.
> Thanx
> Harry
I assume you mean the MATROX G450?
I could be wrong but you may need Xfree 4.0 but don't quote me on that.
------------------------------
From: "Koen Van Impe" <[EMAIL PROTECTED]>
Crossposted-To: alt.os.linux,comp.os.linux.networking
Subject: Security...restricting user-access to home-dir + links
Date: Tue, 2 Jan 2001 01:12:16 +0100
Hello,
I'm having a 'little' security problem.
I give access to some users (through SSH) to my server.
When a user is logged in, he can simply move around with "cd" to another dir
(like /etc).
Now I want to restrict the access of the user to only his homedir
(/home/<user>) and some links (/home/httpd/html & /home/ftp/pub &
/home/scripts).
Does anyone know how I can accomplish this in an easy way?
I know CHROOT + BIND has something to do with it but after reading some
documentation it seems a bit over-kill for such a small (???) requirement
(hey...in Win NT you can make a home-dir and restrict user-access to only
this share).
Thanx for all the help.
Koen Van Impe
Belgium
------------------------------
From: [EMAIL PROTECTED] (Colin Watson)
Subject: Re: RPM Vs. Source Vs. Binary ???
Date: 2 Jan 2001 00:18:40 GMT
MrTaboo <[EMAIL PROTECTED]> wrote:
>Okay, RPM, I must admit, is pretty simple to install AND it allows for an
>easy uninstallation or upgrade of a software package. BUT - some software
>isn't distributed as RPM packages.
Note that there's also the Debian packaging format, .deb.
>Plus, to add to my confusion, I've heard that compiling the source code
>is actually the "bestest" (is that a word?) way to go because it
>optimizes the code for your system.
That's technically true, but in almost all cases (the kernel, the C
library, and CPU-intensive scientific software being possible
exceptions) the difference is not enough to justify the effort, and the
effort of integrating some software packages into a distribution -
making it conform to the policy and "style" of the rest of the system -
can be considerable.
In most cases, using binary packages built for your distribution is the
best way to go. You get the benefit of a package maintainer who's
willing to put the effort into tracking upstream releases and making
sure that the package continues to fit in well with your system, which
is a very considerable benefit unless you have infinite time. Depending
on your distribution, you can also get security fixes in advance of the
upstream maintainer releasing a new version.
With newer C libraries it's even possible for packages to install
libraries in /usr/lib/i686 and so on, which can be optimized for
specific processor types without having to make the package
uninstallable on less capable processors (for instance, Debian unstable
now includes optimized libc6-i586, libc6-i686, and libc6-v9 packages,
which as far as I know are only split out of libc6 for reasons of
space).
Compiling software from source, and going to the effort of integrating
it into your system, is one of the best ways of learning about that
piece of software; don't kid yourself too much about the performance
advantage, though, unless your system is something like a *really*
heavily loaded server. The only real benefit to your system, in my
experience, is if you disagree with the configuration choices made by
the package maintainer.
>Also, RPM keeps track of where everything is installed so it can uninstall
>it later. If I manually install something how can I remove it later? How
>do I figure out what it installed and where it installed it?
Well, you could always learn how to build RPMs yourself. Debian packages
aren't all that difficult to build, and .spec files for RPMs don't look
overly complicated either.
Otherwise, have a look at GNU stow (http://www.gnu.org/software/stow/
and ftp://ftp.gnu.org/gnu/stow/ if your distribution doesn't provide
it), which helps you manage /usr/local trees. Software you install
manually should always be installed into /usr/local, or possibly /opt,
so that your distribution doesn't inadvertently overwrite them.
--
Colin Watson [[EMAIL PROTECTED]]
"'Spirited, isn't he?' Tynian whispered to Ulath. 'Red-haired
people are like that sometimes,' Ulath replied sagely."
------------------------------
From: [EMAIL PROTECTED] (Colin Watson)
Subject: Re: RPM Vs. Source Vs. Binary ???
Date: 2 Jan 2001 00:23:25 GMT
Michael Heiming <[EMAIL PROTECTED]> wrote:
>This and a short view at man rpm tells me, that you can
>build/install/delete/create source rpm,
>they are even available on my distro (SuSE)...
They'd have to be, really. Packages count as derived works of the
software they contain, and copyleft-style licences like the GPL require
you to provide source to derived works. If there are any Linux
distributions that don't provide source packages, I think they're in
quite dodgy territory.
--
Colin Watson [[EMAIL PROTECTED]]
"Ammo is cheap, remember?" - The Internet Oracle
------------------------------
From: Nader <[EMAIL PROTECTED]>
Subject: Re: UDMA hard disk
Date: Mon, 01 Jan 2001 16:21:02 -0800
you may also have to use ide0 instead of ide2
Glitch wrote:
>
> Liu Wu wrote:
>
>> I have a UDMA hard disk. I do the steps according to linux howto.
>> but I input the command line when installation
>>
>> "linux ide2=0xd800,0xdc02"
>>
>> it alawys give me the messages
>>
>> "Unknown option 'ide2=0xd800, 0sdc02'"
>>
>> it seems that it does not know this option yet. I don't know what's wrong. I
>> just did what I am told by the linux howto. it doesn't work. the result is
>> the installation cannot find my hard disk at all.
>>
>
>
> you either need to write it like this
>
> linux ide2="0xd800, 0xdc02"
>
> or like this
> linux append="ide2=0xd800, 0xdc02"
>
>
> I forget which but i'm pretty sure one of them is correct based on info
> in the lilo.conf man page.
> try them and i hope it helps.
--
Nader E. Abyad
@Home [EMAIL PROTECTED]
------------------------------
From: Darren Wyn Rees <[EMAIL PROTECTED]>
Crossposted-To: alt.comp.mail.qmail
Subject: Re: qmail relay
Date: Tue, 2 Jan 2001 00:39:10 +0000 (UTC)
(add alt.comp.mail.qmail)
David <[EMAIL PROTECTED]> wrote:
> RC Walker wrote:
>>
>> I need to set up a linux server. The server is acting as a firewall,
>> also masquerading the clients behind it. I need to configure qmail to
>> all these clients to send messages to the outside world. With
>> 'firewall.server.com' as the out going SMTP server, I get an error
>> message stating that, 'the host (whatever account I am sending to), is
>> not found in rcpthosts'. Any hints on how to fix this?
>>
>> Sorry so long,
>> RCW
The answer to your 'how do I relay question' is listed in the
qmail FAQ, Section 5.4. This is djb's FAQ... the one that comes
with the qmail-1.03 tarball.
If you can't find that, look for Dave Sill's 'Life with Qmail' FAQ.
> Edit /var/qmail/control/rcpthosts and add the host name of the systems
> you want to relay mail for.
No, that is not what rcpthosts is used for (read 'man qmail-smtpd').
> localhost
> hostname1.domain.com
> hostname2.domain.org
If you put these entries in rcpthosts, qmail will accept mail
for hostname1.domain.com etc. but it will not relay mail for
these systems.
--
Darren Wyn Rees [EMAIL PROTECTED]
ASK your ISP to ADD the NEW england.* Newsgroups
http://www.england.news-admin.org/accessfaq.html
------------------------------
From: Nader <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.hardware
Subject: Modem is "busy" - PCI IRQ Sharing problem
Date: Mon, 01 Jan 2001 16:47:05 -0800
I am unable to get my modem (US Robotics 56K FAX INT controller-based PCI,
3COM/USR 3CP5610 family, OEM 2977 model) to work in Linux, although it works
very well in Windows 98. My research to date leads me to believe the problem
is Linux PCI IRQ sharing related, but I don't know what steps to take to resolve
it short of moving PCI cards around (which I strongly prefer to avoid).
The story:
I recently completed an almost successful installation of Caldera 2.3
(2.2.10) and KDE 1.1.1. I am amazed (and refreshed) with the ease of
use and the performance. I am new to Linux, but have a lot of Unix and
software development experience.
I have an ABIT BE6 motherboard with 733MHz CPU, 128M RAM, PCI Bus, 3Com NIC,
Sound Blaster 128, ATI XPERT 99 Video Card, Adaptec SCSI Controller,
HPT366 IDE UDMA 66 Controller, USR Robotics 56K FAX INT modem (OEM 2977
controller based), Intel PCI Bus Master IDE Controller.
I have partitioned the hard drive to dual boot Windows 98 and Linux via
BootMagic. I have no issues in Windows (other than those that Microsoft
provides) and I prefer to leave the hardware settings where they are so
as not to upset Windows.
I use "ide0=0xb400,0xb802" to boot the kernel from within the lilo.conf file.
I learned how to do this in the HPT366 IDE FAQ for the UDMA66 issue.
I recompiled the kernel per the USR FAQ on netllama (since then I learned that
this was not necessary) so that the COM5 modem uses /dev/ttyS4 (= /dev/modem).
When I try to access /dev/modem via kppp, it reports "Sorry, the modem is busy".
I have spent countless hours trying to fix this and have run out of options.
It appears the problem is due to the HPT366 UDMA66 and the USR Modem sharing IRQ 10.
I'd prefer to not move PCI cards around since Windows 98 is happy right
now. I have also tried to use ttyS2 and ttyS3 with various setserial settings.
Should setpci be used? Any suggestions?
I have attached files below to help convey the status of my configuration.
Thanks for your assistance,
Nader
=======================
Windows 98 IRQ Sharing Info
=======================
IRQ 9 3Com Fast Etherlink XL 10/100Mb TX Ethernet NIC (3C905B-TX)
IRQ 9 Creative Labs Sound Blaster PCI128
IRQ 9 Xpert 99/Xpert 2000 (English)
IRQ 9 ACPI IRQ Holder for PCI IRQ Steering
IRQ 9 ACPI IRQ Holder for PCI IRQ Steering
IRQ 9 SCI IRQ used by ACPI bus
IRQ 10 Highpoint Technology Inc. HPT366 Ultra DMA 66 Controller
IRQ 10 Highpoint Technology Inc. HPT366 Ultra DMA 66 Controller
IRQ 10 U.S. Robotics 56K Fax PCI
IRQ 10 ACPI IRQ Holder for PCI IRQ Steering
IRQ 11 Adaptec AIC-7850 PCI SCSI Controller
IRQ 11 Intel 82371AB/EB PCI to USB Universal Host Controller
IRQ 11 ACPI IRQ Holder for PCI IRQ Steering
IRQ 14 Primary IDE controller (dual FIFO)
IRQ 14 Intel 82371AB/EB PCI Bus Master IDE Controller
IRQ 15 Secondary IDE controller (dual FIFO)
IRQ 15 Intel 82371AB/EB PCI Bus Master IDE Controller
===================================================================================================
=================================
Linux - /proc/interrupts
=================================
CPU0
0: 225198 XT-PIC timer
1: 3196 XT-PIC keyboard
2: 0 XT-PIC cascade
8: 0 XT-PIC rtc
9: 0 XT-PIC es1370, eth0
10: 67820 XT-PIC ide0
11: 2387 XT-PIC usb, aic7xxx
12: 45583 XT-PIC PS/2 Mouse
13: 1 XT-PIC fpu
14: 5 XT-PIC ide1
NMI: 0
ERR: 0
===================================================================================================
===================================
Linux - setserial
===================================
/dev/ttyS0, Line 0, UART: 16550A, Port: 0x03f8, IRQ: 4
Baud_base: 115200, close_delay: 50, divisor: 0
closing_wait: 3000, closing_wait2: infinte
Flags: spd_normal skip_test
/dev/ttyS1, Line 1, UART: 16550A, Port: 0x02f8, IRQ: 3
Baud_base: 115200, close_delay: 50, divisor: 0
closing_wait: 3000, closing_wait2: infinte
Flags: spd_normal skip_test
/dev/ttyS2, Line 2, UART: unknown, Port: 0x03e8, IRQ: 4
Baud_base: 115200, close_delay: 50, divisor: 0
closing_wait: 3000, closing_wait2: infinte
Flags: spd_normal skip_test
/dev/ttyS3, Line 3, UART: unknown, Port: 0x02e8, IRQ: 3
Baud_base: 115200, close_delay: 50, divisor: 0
closing_wait: 3000, closing_wait2: infinte
Flags: spd_normal
/dev/ttyS4, Line 4, UART: 16550A, Port: 0xa800, IRQ: 10
Baud_base: 115200, close_delay: 50, divisor: 0
closing_wait: 3000, closing_wait2: infinte
Flags: spd_vhi skip_test
==================================================================================================
=============================
Linux - /proc/pci
=============================
PCI devices found:
Bus 0, device 0, function 0:
Host bridge: Intel 440BX - 82443BX Host (rev 3).
Medium devsel. Master Capable. Latency=32.
Prefetchable 32 bit memory at 0xd0000000 [0xd0000008].
Bus 0, device 1, function 0:
PCI bridge: Intel 440BX - 82443BX AGP (rev 3).
Medium devsel. Master Capable. Latency=64. Min Gnt=136.
Bus 0, device 7, function 0:
ISA bridge: Intel 82371AB PIIX4 ISA (rev 2).
Medium devsel. Fast back-to-back capable. Master Capable. No bursts.
Bus 0, device 7, function 1:
IDE interface: Intel 82371AB PIIX4 IDE (rev 1).
Medium devsel. Fast back-to-back capable. Master Capable. Latency=32.
I/O at 0xf000 [0xf001].
Bus 0, device 7, function 2:
USB Controller: Intel 82371AB PIIX4 USB (rev 1).
Medium devsel. Fast back-to-back capable. IRQ 11. Master Capable.
Latency=32.
I/O at 0xa000 [0xa001].
Bus 0, device 7, function 3:
Bridge: Intel 82371AB PIIX4 ACPI (rev 2).
Medium devsel. Fast back-to-back capable.
Bus 0, device 11, function 0:
SCSI storage controller: Adaptec AIC-7850 (rev 3).
Medium devsel. Fast back-to-back capable. IRQ 11. Master Capable.
Latency=32. Min Gnt=4.Max Lat=4.
I/O at 0xa400 [0xa401].
Non-prefetchable 32 bit memory at 0xdb001000 [0xdb001000].
Bus 0, device 13, function 0:
Serial controller: Unknown vendor Unknown device (rev 1).
Vendor id=12b9. Device id=1008.
Medium devsel. IRQ 10.
I/O at 0xa800 [0xa801].
Bus 0, device 15, function 0:
Multimedia audio controller: Ensoniq AudioPCI (rev 1).
Slow devsel. IRQ 9. Master Capable. Latency=32. Min Gnt=12.Max Lat=128.
I/O at 0xac00 [0xac01].
Bus 0, device 17, function 0:
Ethernet controller: 3Com 3C905B 100bTX (rev 48).
Medium devsel. IRQ 9. Master Capable. Latency=32. Min Gnt=10.Max Lat=10.
I/O at 0xb000 [0xb001].
Non-prefetchable 32 bit memory at 0xdb000000 [0xdb000000].
Bus 0, device 19, function 0:
Unknown mass storage controller: Triones Technologies, Inc. Unknown
device (rev 1).
Vendor id=1103. Device id=4.
Medium devsel. IRQ 10. Master Capable. Latency=248. Min Gnt=8.Max Lat=8.
I/O at 0xb400 [0xb401].
I/O at 0xb800 [0xb801].
I/O at 0xbc00 [0xbc01].
Bus 0, device 19, function 1:
Unknown mass storage controller: Triones Technologies, Inc. Unknown
device (rev 1).
Vendor id=1103. Device id=4.
Medium devsel. IRQ 10. Master Capable. Latency=248. Min Gnt=8.Max Lat=8.
I/O at 0xc000 [0xc001].
I/O at 0xc400 [0xc401].
I/O at 0xc800 [0xc801].
Bus 1, device 0, function 0:
VGA compatible controller: ATI Unknown device (rev 0).
Vendor id=1002. Device id=524c.
Medium devsel. Fast back-to-back capable. IRQ 9. Master Capable.
Latency=32. Min Gnt=8.
Prefetchable 32 bit memory at 0xd4000000 [0xd4000008].
I/O at 0x9000 [0x9001].
Non-prefetchable 32 bit memory at 0xd9000000 [0xd9000000].
=================================================================================================
=============================
Linux - lspci
=============================
00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge
(rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 32 set
Region 0: Memory at d0000000 (32-bit, prefetchable)
Capabilities: [a0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=1
Command: RQ=31 SBA+ AGP- 64bit- FW- Rate=1
00:01.0 PCI bridge: Intel Corporation 440BX/ZX - 82443BX/ZX AGP bridge
(rev 03)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 set
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00009000-00009fff
Memory behind bridge: d8000000-d9ffffff
Prefetchable memory behind bridge: d4000000-d7ffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+
00:07.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01)
(prog-if 80)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 set
Region 4: I/O ports at f000
00:07.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 set
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at a000
00:07.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:0b.0 SCSI storage controller: Adaptec AIC-7850 (rev 03)
Subsystem: Unknown device 9004:7850
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 4 min, 4 max, 32 set, cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at a400
Region 1: Memory at db001000 (32-bit, non-prefetchable)
Capabilities: [dc] Power Management version 1
Flags: PMEClk- AuxPwr- DSI+ D1- D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0d.0 Serial controller: US Robotics: Unknown device 1008 (rev 01)
(prog-if 02)
Subsystem: Unknown device 12b9:00a2
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at a800
Capabilities: [dc] Power Management version 2
Flags: PMEClk- AuxPwr- DSI- D1- D2+ PME+
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:0f.0 Multimedia audio controller: Ensoniq ES1370 [AudioPCI] (rev 01)
Subsystem: Unknown device 4942:4c4c
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 12 min, 128 max, 32 set
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at ac00
00:11.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone]
(rev 30)
Subsystem: Unknown device 10b7:9055
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 10 min, 10 max, 32 set, cache line size 08
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at b000
Region 1: Memory at db000000 (32-bit, non-prefetchable)
Capabilities: [dc] Power Management version 1
Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:13.0 Unknown mass storage controller: Triones Technologies, Inc.:
Unknown device 0004 (rev 01)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 8 min, 8 max, 248 set, cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at b400
Region 1: I/O ports at b800
Region 4: I/O ports at bc00
00:13.1 Unknown mass storage controller: Triones Technologies, Inc.:
Unknown device 0004 (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 8 min, 8 max, 248 set, cache line size 08
Interrupt: pin B routed to IRQ 10
Region 0: I/O ports at c000
Region 1: I/O ports at c400
Region 4: I/O ports at c800
01:00.0 VGA compatible controller: ATI Technologies Inc: Unknown device 524c
Subsystem: Unknown device 1002:0008
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 8 min, 32 set, cache line size 08
Interrupt: pin A routed to IRQ 9
Region 0: Memory at d4000000 (32-bit, prefetchable)
Region 1: I/O ports at 9000
Region 2: Memory at d9000000 (32-bit, non-prefetchable)
Capabilities: [50] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=21
Command: RQ=31 SBA+ AGP- 64bit- FW- Rate=21
Capabilities: [5c] Power Management version 1
Flags: PMEClk- AuxPwr- DSI- D1+ D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
==============================================================================================
======================
Linux - /proc/ioports
======================
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
01f0-01f7 : ide1
02f8-02ff : serial(auto)
03c0-03df : vga+
03f6-03f6 : ide1
03f8-03ff : serial(auto)
a000-a01f : usb-uhci
a400-a4be : aic7xxx
a800-a807 : serial(set)
ac00-ac3f : es1370
b000-b07f : eth0
b400-b407 : ide0
b802-b802 : ide0
f000-f007 : ide1
f008-f00f : ide2
------------------------------
From: [EMAIL PROTECTED] (James Rose)
Crossposted-To: comp.os.linux.hardware
Subject: Re: Support Maxtor G450
Date: Tue, 02 Jan 2001 00:35:49 GMT
On Sun, 31 Dec 2000 13:40:04 +0100, "Harald Adams"
<[EMAIL PROTECTED]> wrote:
>Hi,
>does anybody out there know, how I can setup which X server to support the
>new maxtor G450 graphic board under Suse 7.0.
If you use the SVGA driver and the correct scan rates for your card
and monitor, it will work. The SVGA driver is designed to work with
virtually every card.
------------------------------
From: "C.E. Logan" <[EMAIL PROTECTED]>
Subject: Problems with DSL and WinLinux 2000
Date: Mon, 1 Jan 2001 18:58:12 -0600
Has anyone been successful in getting DSL to work with WinLinux 2000?
If so, could you please tell me how you did it. It seems to be a bit
different from Mandrake 7, which is the only distro I ever had work right,
when I had two hard drives. I thought I'd give this new distro a try since
it installs on top of Windows and sits idle as an icon until you click on it
to boot.
If you could tell me how to get the DSL to work on the WinLinux 2000 as well
as anything else you may have encountered with it, please let me know.
Thanks!
CE
------------------------------
** FOR YOUR REFERENCE **
The service address, to which questions about the list itself and requests
to be added to or deleted from it should be directed, is:
Internet: [EMAIL PROTECTED]
You can send mail to the entire list by posting to comp.os.linux.setup.
Linux may be obtained via one of these FTP sites:
ftp.funet.fi pub/Linux
tsx-11.mit.edu pub/linux
sunsite.unc.edu pub/Linux
End of Linux-Setup Digest
******************************
