Dear Linuxer,
Tolongin dong, mau nanya dikit nih (maklum newbie)
saya mau ngeset NIC tapi tipe nya 3Com 3C319 Token-Ring ISA,
menurut FAQ dan HOWTO dari Token-Ringnya katanya pake
ibmtr, tapi ngesetnya gimana ? (udah muter-muter masih pusing)
udah dicobain pake isapnp tapi ngak bisa up juga.
isi dari isapnp.conf :
...cut...
# Trying port address 0273
# Board 1 has serial identifier 17 08 07 04 c3 90 31 6d 50
# (DEBUG)
(READPORT 0x0273)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
# Card 1: (serial identifier 17 08 07 04 c3 90 31 6d 50)
# Vendor Id TCM3190, Serial Number 134677699, checksum 0x17.
# Version 1.0, Vendor version 1.0
# ANSI string -->3Com TokenLink Velocity ISA <--
#
# Logical device id TCM3190
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x38
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3e
# Device supports vendor reserved register @ 0x3f
(CONFIGURE TCM3190/134677699 (LD 0
# IRQ 3, 5, 6, 7, 9, 10, 11 or 15.
# High true, edge sensitive interrupt (by default)
(INT 0 (IRQ 3 (MODE +E)))
# Multiple choice time, choose one only !
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0a20
# Maximum IO base address 0x0a24
# IO base alignment 4 bytes
# Number of IO addresses required: 4
# (IO 0 (SIZE 4) (BASE 0x0a20) (CHECK))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0210
# Maximum IO base address 0x0260
# IO base alignment 16 bytes
# Number of IO addresses required: 16
(IO 0 (SIZE 16) (BASE 0x0210) (CHECK))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0280
# Maximum IO base address 0x02e0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0280) (CHECK))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x03e0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0300) (CHECK))
# End dependent functions
# Memory is writeable
# Memory is non-cacheable
# Memory decode supports high address
# memory is 16-bit only
# memory is an expansion ROM
# Minimum memory base address 0x0c8000
# Maximum memory base address 0x0de000
# Range base alignment mask 0xff2000 bytes
# Range length 8192 bytes
# Choose UPPER = Range, or UPPER = Upper limit to suit hardware
(MEM 0 (BASE 0x0ca000) (MODE wr) (UPPER 0x0cb000))
# (MEM 0 (BASE 0x0c8000) (MODE wr) (UPPER 0x002000))
# Memory is writeable
# Memory is non-cacheable
# Memory decode supports high address
# memory is 16-bit only
# Minimum memory base address 0x0c8000
# Maximum memory base address 0x0dc000
# Range base alignment mask 0xff4000 bytes
# Range length 16384 bytes
# Choose UPPER = Range, or UPPER = Upper limit to suit hardware
(MEM 1 (BASE 0x0c8000) (MODE wr) (UPPER 0x0cc000))
# (MEM 1 (BASE 0x0c8000) (MODE wr) (UPPER 0x004000))
(NAME "TCM3190/134677699[0]{3Com TokenLink Velocity ISA }")
(ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
/*-eof-isapnp.conf*/
saya udah coba :
$insmod ibmtr0 io=0x210 irq=3
Using /lib/modules/2.2.16/net/ibmtr.o: init_module: Device or resource busy
Hint: this error can be caused by incorrect module parameters,
including invalid IO or IRQ parameters
isi dari /var/log/syslog
Apr 19 20:55:36 bp3 kernel: PPP: version 2.3.7 (demand dialling)
Apr 19 20:55:36 bp3 kernel: PPP line discipline registered.
Apr 19 20:55:36 bp3 kernel: PPP BSD Compression module registered
Apr 19 20:55:36 bp3 kernel: ibmtr: register_trdev() returned non-zero.
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
trus mau tanya juga :
Apr 19 21:15:33 bp3 -- MARK --
^^^^^^^^^^
MARK : maksudnya apa nih ...
Tolong dong ada yang mau bantu ?
makasih banget
Sorry, pak admin BWnya rada gede
--
Utk berhenti langganan, kirim email ke [EMAIL PROTECTED]
Dapatkan FAQ milis dg mengirim email kosong ke [EMAIL PROTECTED]
Informasi arsip di http://www.linux.or.id/milis.php3
