Hello, I just got this: <7>IO APIC #2...... <7>.... register #00: 02000000 <7>....... : physical APIC id: 02 <7>.... register #01: 00170020 <7>....... : max redirection entries: 0017 <7>....... : IO APIC version: 0020 <4> WARNING: unexpected IO-APIC, please mail <4> to [EMAIL PROTECTED] <7>.... register #02: 00000000 <7>....... : arbitration: 00 \ETC The whole /var/log/boot.msg:
Inspecting /boot/System.map Loaded 13032 symbols from /boot/System.map. Symbols match kernel version 2.3.99. No module symbols loaded. klogd 1.3-3, log source = ksyslog started. <4>Linux version 2.3.99-pre6 (root@advisor1) (gcc version 2.95.2 19991024 (release)) #3 SMP Wed May 17 14:22:24 GMT 2000 <4>e820: 0009fc00 @ 00000000 (usable) <4>e820: 00000400 @ 0009fc00 (reserved) <4>e820: 00020000 @ 000e0000 (reserved) <4>e820: 1fee0000 @ 00100000 (usable) <4>e820: 00012000 @ 1ffe0000 (ACPI data) <4>e820: 0000e000 @ 1fff2000 (ACPI NVS) <4>e820: 00001000 @ fec00000 (reserved) <4>e820: 00001000 @ fee00000 (reserved) <4>e820: 00080000 @ fff80000 (reserved) <4>Scan SMP from c0000000 for 1024 bytes. <4>Scan SMP from c009fc00 for 1024 bytes. <4>Scan SMP from c00f0000 for 65536 bytes. <4>found SMP MP-table at 000ff780 <4>hm, page 000ff000 reserved twice. <4>hm, page 00100000 reserved twice. <4>hm, page 000f0000 reserved twice. <4>hm, page 000f1000 reserved twice. <4>On node 0 totalpages: 131040 <4>zone(0): 4096 pages. <4>zone(1): 126944 pages. <4>zone(2): 0 pages. <4>Intel MultiProcessor Specification v1.1 <4> Virtual Wire compatibility mode. <4>OEM ID: HP_PDCO Product ID: CARMEL__ APIC at: 0xFEE00000 <4>Processor #0 Pentium(tm) Pro APIC version 17 <4> Floating point unit present. <4> Machine Exception supported. <4> 64 bit compare & exchange supported. <4> Internal APIC present. <4> Bootup CPU <4>Processor #1 Pentium(tm) Pro APIC version 17 <4> Floating point unit present. <4> Machine Exception supported. <4> 64 bit compare & exchange supported. <4> Internal APIC present. <4>Bus #0 is PCI <4>Bus #1 is PCI <4>Bus #2 is PCI <4>Bus #3 is PCI <4>Bus #4 is PCI <4>Bus #5 is ISA <4>I/O APIC #2 Version 32 at 0xFEC00000. <4>Int: type 3, pol 0, trig 0, bus 5, IRQ 00, APIC ID 2, APIC INT 00 <4>Int: type 0, pol 0, trig 0, bus 5, IRQ 01, APIC ID 2, APIC INT 01 <4>Int: type 0, pol 0, trig 0, bus 5, IRQ 00, APIC ID 2, APIC INT 02 <4>Int: type 0, pol 0, trig 0, bus 5, IRQ 03, APIC ID 2, APIC INT 03 <4>Int: type 0, pol 0, trig 0, bus 5, IRQ 04, APIC ID 2, APIC INT 04 <4>Int: type 0, pol 0, trig 0, bus 5, IRQ 05, APIC ID 2, APIC INT 05 <4>Int: type 0, pol 0, trig 0, bus 5, IRQ 06, APIC ID 2, APIC INT 06 <4>Int: type 0, pol 0, trig 0, bus 5, IRQ 07, APIC ID 2, APIC INT 07 <4>Int: type 0, pol 1, trig 1, bus 5, IRQ 08, APIC ID 2, APIC INT 08 <4>Int: type 0, pol 0, trig 0, bus 5, IRQ 09, APIC ID 2, APIC INT 09 <4>Int: type 0, pol 0, trig 0, bus 5, IRQ 0a, APIC ID 2, APIC INT 0a <4>Int: type 0, pol 0, trig 0, bus 5, IRQ 0b, APIC ID 2, APIC INT 0b <4>Int: type 0, pol 0, trig 0, bus 5, IRQ 0c, APIC ID 2, APIC INT 0c <4>Int: type 0, pol 0, trig 0, bus 5, IRQ 0d, APIC ID 2, APIC INT 0d <4>Int: type 0, pol 0, trig 0, bus 5, IRQ 0e, APIC ID 2, APIC INT 0e <4>Int: type 0, pol 0, trig 0, bus 5, IRQ 0f, APIC ID 2, APIC INT 0f <4>Int: type 0, pol 3, trig 3, bus 4, IRQ 00, APIC ID 2, APIC INT 10 <4>Int: type 0, pol 3, trig 3, bus 0, IRQ 7c, APIC ID 2, APIC INT 10 <4>Int: type 0, pol 3, trig 3, bus 1, IRQ 14, APIC ID 2, APIC INT 11 <4>Int: type 0, pol 3, trig 3, bus 3, IRQ 24, APIC ID 2, APIC INT 12 <4>Int: type 0, pol 3, trig 3, bus 0, IRQ 7f, APIC ID 2, APIC INT 13 <4>Int: type 0, pol 3, trig 3, bus 1, IRQ 2c, APIC ID 2, APIC INT 13 <4>Int: type 2, pol 0, trig 0, bus 5, IRQ 00, APIC ID 2, APIC INT 17 <4>Lint: type 3, pol 0, trig 0, bus 0, IRQ 00, APIC ID ff, APIC LINT 00 <4>Lint: type 1, pol 0, trig 0, bus 0, IRQ 00, APIC ID ff, APIC LINT 01 <4>Processors: 2 <4>mapped APIC to ffffe000 (fee00000) <4>mapped IOAPIC to ffffd000 (fec00000) <4>Initializing CPU#0 <4>Detected 797483848 Hz processor. <4>Console: colour VGA+ 80x25 <4>Calibrating delay loop... 1592.52 BogoMIPS <4>Memory: 511924k/524160k available (1505k kernel code, 11848k reserved, 124k data, 192k init, 0k highmem) <4>VFS: DCACHE hash table configured to 65536 entries <4>Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes) <4>Page-cache hash table entries: 131072 (order: 7, 524288 bytes) <4>VFS: INODE hash table configured to 32768 entries <6>Checking 386/387 coupling... OK, FPU using exception 16 error reporting. <6>Checking 'hlt' instruction... OK. <4>POSIX conformance testing by UNIFIX <4>mtrr: v1.36 (20000221) Richard Gooch ([EMAIL PROTECTED]) <4>CPU0: Intel Pentium III (Coppermine) stepping 03 <4>per-CPU timeslice cutoff: 714.21 usecs. <4>Getting VERSION: 40011 <4>Getting VERSION: 40011 <4>Getting LVT0: 700 <4>Getting LVT1: 400 <4>enabled ExtINT on CPU#0 <4>ESR value before enabling vector: 00000004 <4>ESR value after enabling vector: 00000000 <4>CPU present map: 3 <4>Booting processor 1/1 eip 2000 <4>Setting warm reset code and vector. <4>1. <4>2. <4>3. <4>Asserting INIT. <4>Waiting for send to finish... <4>+Deasserting INIT. <4>Waiting for send to finish... <4>+#startup loops: 2. <4>Sending STARTUP #1. <4>After apic_write. <4>Startup point 1. <4>Waiting for send to finish... <4>+Initializing CPU#1 <4>CPU#1 (phys ID: 1) waiting for CALLOUT <4>Sending STARTUP #2. <4>After apic_write. <4>Startup point 1. <4>Waiting for send to finish... <4>+After Startup. <4>Before Callout 1. <4>After Callout 1. <4>CALLIN, before setup_local_APIC(). <4>masked ExtINT on CPU#1 <4>ESR value before enabling vector: 00000000 <4>ESR value after enabling vector: 00000000 <4>Calibrating delay loop... 1592.52 BogoMIPS <4>Stack at about c199bfbc <4>OK. <4>CPU1: Intel Pentium III (Coppermine) stepping 03 <4>CPU has booted. <4>Before bogomips. <6>Total of 2 processors activated (3185.05 BogoMIPS). <4>Before bogocount - setting activated=1. <4>Boot done. <4>ENABLING IO-APIC IRQs <6>...changing IO-APIC physical APIC ID to 2 ... ok. <4>Synchronizing Arb IDs. <7>init IO_APIC IRQs <7> IO-APIC (apicid-pin) 2-0, 2-20, 2-21, 2-22, 2-23 not connected. <6>..TIMER: vector=81 pin1=2 pin2=0 <6>activating NMI Watchdog ... done. <7>number of MP IRQ sources: 23. <7>number of IO-APIC #2 registers: 24. <6>testing the IO APIC....................... <4> <7>IO APIC #2...... <7>.... register #00: 02000000 <7>....... : physical APIC id: 02 <7>.... register #01: 00170020 <7>....... : max redirection entries: 0017 <7>....... : IO APIC version: 0020 <4> WARNING: unexpected IO-APIC, please mail <4> to [EMAIL PROTECTED] <7>.... register #02: 00000000 <7>....... : arbitration: 00 <7>.... IRQ redirection table: <7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: <7> 00 000 00 1 0 0 0 0 0 0 00 <7> 01 0FF 0F 0 0 0 0 0 1 1 59 <7> 02 0FF 0F 0 0 0 0 0 1 1 51 <7> 03 0FF 0F 0 0 0 0 0 1 1 61 <7> 04 0FF 0F 0 0 0 0 0 1 1 69 <7> 05 0FF 0F 0 0 0 0 0 1 1 71 <7> 06 0FF 0F 0 0 0 0 0 1 1 79 <7> 07 0FF 0F 0 0 0 0 0 1 1 81 <7> 08 0FF 0F 0 0 0 0 0 1 1 89 <7> 09 0FF 0F 0 0 0 0 0 1 1 91 <7> 0a 0FF 0F 0 0 0 0 0 1 1 99 <7> 0b 0FF 0F 0 0 0 0 0 1 1 A1 <7> 0c 0FF 0F 0 0 0 0 0 1 1 A9 <7> 0d 000 00 1 0 0 0 0 0 0 00 <7> 0e 0FF 0F 0 0 0 0 0 1 1 B1 <7> 0f 0FF 0F 0 0 0 0 0 1 1 B9 <7> 10 0FF 0F 1 1 0 1 0 1 1 C1 <7> 11 0FF 0F 1 1 0 1 0 1 1 C9 <7> 12 0FF 0F 1 1 0 1 0 1 1 D1 <7> 13 0FF 0F 1 1 0 1 0 1 1 D9 <7> 14 000 00 1 0 0 0 0 0 0 00 <7> 15 000 00 1 0 0 0 0 0 0 00 <7> 16 000 00 1 0 0 0 0 0 0 00 <7> 17 000 00 1 0 0 0 0 0 0 00 <7>IRQ to pin mappings: <7>IRQ0 -> 2 <7>IRQ1 -> 1 <7>IRQ3 -> 3 <7>IRQ4 -> 4 <7>IRQ5 -> 5 <7>IRQ6 -> 6 <7>IRQ7 -> 7 <7>IRQ8 -> 8 <7>IRQ9 -> 9 <7>IRQ10 -> 10 <7>IRQ11 -> 11 <7>IRQ12 -> 12 <7>IRQ13 -> 13 <7>IRQ14 -> 14 <7>IRQ15 -> 15 <7>IRQ16 -> 16 <7>IRQ17 -> 17 <7>IRQ18 -> 18 <7>IRQ19 -> 19 <6>.................................... done. <4>calibrating APIC timer ... <4>..... CPU clock speed is 797.4485 MHz. <4>..... host bus clock speed is 132.9080 MHz. <4>cpu: 0, clocks: 1329080, slice: 443026 <4>CPU0<C0:1329072,C:886032,D:14,S:443026,C:1329080> <4>cpu: 1, clocks: 1329080, slice: 443026 <4>CPU1<C0:1329072,C:443008,D:12,S:443026,C:1329080> <4>checking TSC synchronization across CPUs: passed. <4>Setting commenced=1, go go go <4>PCI: PCI BIOS revision 2.10 entry at 0xfdb91, last bus=4 <4>PCI: Using configuration type 1 <4>PCI: Probing PCI hardware <4>PCI: Using IRQ router default [8086/2418] at 00:1f.0 <4>PCI->APIC IRQ transform: (B0,I31,P3) -> 19 <4>PCI->APIC IRQ transform: (B0,I31,P1) -> 16 <4>PCI->APIC IRQ transform: (B4,I0,P0) -> 16 <4>PCI->APIC IRQ transform: (B3,I9,P0) -> 18 <4>PCI->APIC IRQ transform: (B1,I5,P0) -> 17 <4>PCI->APIC IRQ transform: (B1,I11,P0) -> 19 <3>PCI: Cannot allocate resource region 0 of device 03:00.0 <4>isapnp: Scanning for Pnp cards... <4>isapnp: No Plug & Play device found <6>Linux NET4.0 for Linux 2.3 <6>Based upon Swansea University Computer Society NET3.039 <6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. <6>NET4: Linux TCP/IP 1.0 for NET4.0 <6>IP Protocols: ICMP, UDP, TCP, IGMP <4>IP: routing cache hash table of 2048 buckets, 32Kbytes <4>TCP: Hash tables configured (established 16384 bind 21845) <4>Initializing RT netlink socket <4>Starting kswapd v1.6 <4>pty: 256 Unix98 ptys configured <6>(scsi0) <Adaptec AIC-7892 Ultra 160/m SCSI host adapter> found at PCI 3/9/0 <6>(scsi0) Wide Channel, SCSI ID=7, 32/255 SCBs <6>(scsi0) Downloading sequencer code... 392 instructions downloaded <4>scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.2.0/3.2.4 <4> <Adaptec AIC-7892 Ultra 160/m SCSI host adapter> <4>scsi : 1 host. <6>(scsi0:0:0:0) Synchronous at 160.0 Mbyte/sec, offset 31. <4> Vendor: QUANTUM Model: ATLAS 10K 18WLS Rev: UCHK <4> Type: Direct-Access ANSI SCSI revision: 03 <4>Detected scsi disk sda at scsi0, channel 0, id 0, lun 0 <6>(scsi0:0:4:0) Synchronous at 160.0 Mbyte/sec, offset 31. <4> Vendor: QUANTUM Model: ATLAS 10K 9WLS Rev: UCHK <4> Type: Direct-Access ANSI SCSI revision: 03 <4>Detected scsi disk sdb at scsi0, channel 0, id 4, lun 0 <6>(scsi0:0:8:0) Synchronous at 160.0 Mbyte/sec, offset 31. <4> Vendor: QUANTUM Model: ATLAS 10K 18WLS Rev: UCHK <4> Type: Direct-Access ANSI SCSI revision: 03 <4>Detected scsi disk sdc at scsi0, channel 0, id 8, lun 0 <4>scsi : detected 3 SCSI disks total. <4>SCSI device sda: hdwr sector= 512 bytes. Sectors= 35566480 [17366 MB] [17.4 GB] <6>Partition check: <6> sda: sda1 sda2 <4>SCSI device sdb: hdwr sector= 512 bytes. Sectors= 17783240 [8683 MB] [8.7 GB] <6> sdb: sdb1 sdb2 sdb3 <4>SCSI device sdc: hdwr sector= 512 bytes. Sectors= 35566480 [17366 MB] [17.4 GB] <6> sdc: sdc1 sdc2 <6>Real Time Clock Driver v1.10b <6>8139too Fast Ethernet driver 0.9.4 loaded <6>eth0: SMC1211TX EZCard 10/100 (RealTek RTL8139) at 0xfc7ffc00, IRQ 19, 00:10:b5:48:01:f1. <3>kmem_create: Forcing size word alignment - nfs_fh <4>VFS: Mounted root (ext2 filesystem) readonly. <4>Freeing unused kernel memory: 192k freed <6>Adding Swap: 530104k swap-space (priority -1) Kernel logging (ksyslog) stopped. Kernel log daemon terminating.
This is `uname -a`: Linux advisor1 2.3.99-pre6 #3 SMP Wed May 17 14:22:24 GMT 2000 i686 unknown (SuSE Linux 6.4 with this kernel running on a dual 800 MHz Pentium III (Coppermine) stepping 03 machine) --- 1. Does this mean my system could be unstable? 2. Would you like any more info for updating your driver? Bye, Nils.
