This patch adds support for 1 to 8 BPW to driver and removes excess BPW validation since this is already checked by SPI core.
Signed-off-by: Alexander Shiyan <[email protected]> --- drivers/spi/spi-clps711x.c | 39 ++++++++++++++++----------------------- 1 file changed, 16 insertions(+), 23 deletions(-) diff --git a/drivers/spi/spi-clps711x.c b/drivers/spi/spi-clps711x.c index 0b80624..d9fa933 100644 --- a/drivers/spi/spi-clps711x.c +++ b/drivers/spi/spi-clps711x.c @@ -31,6 +31,7 @@ struct spi_clps711x_data { u8 *tx_buf; u8 *rx_buf; + unsigned int bpw; int len; int chipselect[0]; @@ -56,18 +57,12 @@ static void spi_clps711x_setup_mode(struct spi_device *spi) clps_writew(clps_readw(SYSCON3) & ~SYSCON3_ADCCKNSEN, SYSCON3); } -static int spi_clps711x_setup_xfer(struct spi_device *spi, - struct spi_transfer *xfer) +static void spi_clps711x_setup_xfer(struct spi_device *spi, + struct spi_transfer *xfer) { u32 speed = xfer->speed_hz ? : spi->max_speed_hz; - u8 bpw = xfer->bits_per_word; struct spi_clps711x_data *hw = spi_master_get_devdata(spi->master); - if (bpw != 8) { - dev_err(&spi->dev, "Unsupported master bus width %i\n", bpw); - return -EINVAL; - } - /* Setup SPI frequency divider */ if (!speed || (speed >= hw->max_speed_hz)) clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) | @@ -81,38 +76,36 @@ static int spi_clps711x_setup_xfer(struct spi_device *spi, else clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) | SYSCON1_ADCKSEL(0), SYSCON1); - - return 0; } static int spi_clps711x_transfer_one_message(struct spi_master *master, struct spi_message *msg) { struct spi_clps711x_data *hw = spi_master_get_devdata(master); + struct spi_device *spi = msg->spi; struct spi_transfer *xfer; - int status = 0, cs = hw->chipselect[msg->spi->chip_select]; + int cs = hw->chipselect[spi->chip_select]; - spi_clps711x_setup_mode(msg->spi); + spi_clps711x_setup_mode(spi); list_for_each_entry(xfer, &msg->transfers, transfer_list) { u8 data; - if (spi_clps711x_setup_xfer(msg->spi, xfer)) { - status = -EINVAL; - goto out_xfr; - } + spi_clps711x_setup_xfer(spi, xfer); - gpio_set_value(cs, !!(msg->spi->mode & SPI_CS_HIGH)); + gpio_set_value(cs, !!(spi->mode & SPI_CS_HIGH)); reinit_completion(&hw->done); hw->len = xfer->len; + hw->bpw = xfer->bits_per_word ? : spi->bits_per_word; hw->tx_buf = (u8 *)xfer->tx_buf; hw->rx_buf = (u8 *)xfer->rx_buf; /* Initiate transfer */ data = hw->tx_buf ? *hw->tx_buf++ : 0; - clps_writel(data | SYNCIO_FRMLEN(8) | SYNCIO_TXFRMEN, SYNCIO); + clps_writel(data | SYNCIO_FRMLEN(hw->bpw) | SYNCIO_TXFRMEN, + SYNCIO); wait_for_completion(&hw->done); @@ -121,13 +114,12 @@ static int spi_clps711x_transfer_one_message(struct spi_master *master, if (xfer->cs_change || list_is_last(&xfer->transfer_list, &msg->transfers)) - gpio_set_value(cs, !(msg->spi->mode & SPI_CS_HIGH)); + gpio_set_value(cs, !(spi->mode & SPI_CS_HIGH)); msg->actual_length += xfer->len; } -out_xfr: - msg->status = status; + msg->status = 0; spi_finalize_current_message(master); return 0; @@ -146,7 +138,8 @@ static irqreturn_t spi_clps711x_isr(int irq, void *dev_id) /* Handle TX */ if (--hw->len > 0) { data = hw->tx_buf ? *hw->tx_buf++ : 0; - clps_writel(data | SYNCIO_FRMLEN(8) | SYNCIO_TXFRMEN, SYNCIO); + clps_writel(data | SYNCIO_FRMLEN(hw->bpw) | SYNCIO_TXFRMEN, + SYNCIO); } else complete(&hw->done); @@ -180,7 +173,7 @@ static int spi_clps711x_probe(struct platform_device *pdev) master->bus_num = pdev->id; master->mode_bits = SPI_CPHA | SPI_CS_HIGH; - master->bits_per_word_mask = SPI_BPW_MASK(8); + master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 8); master->num_chipselect = pdata->num_chipselect; master->setup = spi_clps711x_setup; master->transfer_one_message = spi_clps711x_transfer_one_message; -- 1.8.3.2 -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
