Hi,

Am 28.10.2014 um 21:16 schrieb Maxime Ripard:
> Hi Chen-Yu,
> 
> On Tue, Oct 28, 2014 at 05:50:41PM +0800, Chen-Yu Tsai wrote:
>> The A80 Optimus board has 3 usable LEDs that are controlled via GPIO.
>>
>> This patch adds support for 2 of them which are driver by GPIOs in the
>> main pin controller. The remaining one uses GPIO from the R_PIO
>> controller, which we don't support yet.
>>
>> Signed-off-by: Chen-Yu Tsai <[email protected]>
>> ---
>>  arch/arm/boot/dts/sun9i-a80-optimus.dts | 25 +++++++++++++++++++++++++
>>  1 file changed, 25 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts 
>> b/arch/arm/boot/dts/sun9i-a80-optimus.dts
>> index 25fe775..91eda76 100644
>> --- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
>> +++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
>> @@ -64,6 +64,13 @@
>>                              /* Enable internal pull-up */
>>                              allwinner,pull = <1>;
>>                      };
>> +
>> +                    led_pins_optimus: led_pins@0 {

Here too, led-pins@0 would be more in line with DT conventions.

>> +                            allwinner,pins = "PH0", "PH1";
>> +                            allwinner,function = "gpio_out";
>> +                            allwinner,drive = <0>;
>> +                            allwinner,pull = <0>;
>> +                    };
>>              };
>>  
>>              uart0: serial@07000000 {
>> @@ -78,4 +85,22 @@
>>                      status = "okay";
>>              };
>>      };
>> +
>> +    leds {
>> +            compatible = "gpio-leds";
>> +            pinctrl-names = "default";
>> +            pinctrl-0 = <&led_pins_optimus>;
>> +
>> +            led2 {
>> +                    label = "a80_optimus:led2:usr";
> 
> We're usually using a dash instead of an underscore as a separator.

I wonder, why a80_? The board is labeled "Allwinner Tech Optimus Board",
and the Cubietruck LEDs are not prefixed with a20_ either.

>> +                    gpios = <&pio 7 0 0>;
>> +            };
>> +
>> +            /* led3 is on PM15, in R_PIO */
> 
> You were saying that there is three LEDs, why start the numbering at
> 2?

They are labeled "LED2", "LED4", "LED3" right-to-left.
Additionally there's a "PWR" LED, maybe that counts as number 1...

>> +
>> +            led4 {
>> +                    label = "a80_optimus:led4:usr";
>> +                    gpios = <&pio 7 1 0>;
>> +            };
>> +    };
>>  };
> 
> The rest of your patchset is fine for me, we just need to get the
> pinctrl driver merged first :)

Cheers,
Andreas

-- 
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg

Attachment: signature.asc
Description: OpenPGP digital signature

Reply via email to