Hi,
On 05/26/2015 09:34 AM, Roy Spliet wrote:
Hello Hans,
Re-sent to everybody instead of just you. Reply inline.
Op 25-05-15 om 22:39 schreef Hans de Goede:
Hi,
On 25-05-15 20:35, Hans de Goede wrote:
Hi,
On 22-05-15 09:04, Roy Spliet wrote:
Hello,
For my set-up I made use of Boris Brezillon's sunxi-nand tree[1], or actually I
rebased his patches on top of 4.0rc7. This basically adds support for NAND-chip
partitioning, ECC and randomisation. Docs for the DT specification in
Documentation/devicetree/bindings/mtd/sunxi-nand.txt , and an example can be
found in arch/arm/boot/dts/sun7i-a20-cubietruck.dts . [2] lists the acceptable
configuration options for the boot and boot_rescue partitions, make sure to
pick one of these (which should be no problem for MLC-type nand). The ECC mode
for these boot partitions is called hw_syndrome.
Assuming you now have a Linux set-up kernel based on this tree with NAND
support on an MMC, for U-boot what you should currently do is:
1) in include/configs/sunxi-common.h, adjust the parameters
<CONFIG_NAND_SUNXI_>PAGE_SIZE, ECC_STEP, ECC_STRENGTH to match your NAND chip
and DT configuration.
2) Build
3) Use your MMC to flash u-boot-sunxi-with-spl.bin onto NAND:
# flash_erase /dev/mtd0
# nandwrite -p /dev/mtd0 u-boot-sunxi-with-spl.bin
4) Reboot without the MMC card and see U-boot load
Ok, it took me way longer then I wanted (see below) but I've this
working now. It is cool to see u-boot load from nand :)
That should be all.
@Alex: To answer your question specifically: It's likely that the parameters in
sunxi-common.h mentioned above might not match your NAND-chip configuration in
the Linux kernel. I can't tell you precisely how to fetch these details from
the 3.4 kernel, sorry. I recall Daniel using 24-bit strength ECC with otherwise
equal parameters, but perhaps he can help you with this better than I can.
Alex, could it be that you are writing the nand using
a (rebased) version of bbrezillon's sunxi-nand-next branch ?
I started with that too because it is much newer and contains
various bug fixes, but it seems that it also contains a new
bug causing it to write the NAND in such a way that the BROM
and u-boot SPL code will not read it.
I've just pushed a rebased version of the sunxi-nand branch of
Boris here:
https://github.com/jwrdegoede/linux-sunxi/commits/sunxi-nand-experiment
And that works for me, where as before I got the exact same errors
trying to fel load a nand enabled spl.
I'm working on merging over all the changes from the sunxi-nand-next
branch onto my working sunxi-nand-experiment branch 1 by 1 until
I find the one which causes the breakage...
Ok, so quick update the breakage was caused by this commit:
https://github.com/bbrezillon/linux-sunxi/commit/7f7324bc6170a45742352070fb45170779a3611c
When it was rebased someone (Boris I guess) forgot to remove the
"chip->read_buf(mtd, NULL, ecc->size);" line at line 1075 (after the patch) and
likewise the "chip->write_buf(mtd, buf + (i * ecc->size), ecc->size);" line at
line 1161. With these 2 lines removed the sunxi-nand-next branch from Boris,
rebased on 4.1-rc1 can write the nand boot parts and the brom / spl can load
the spl / resp. u-boot.bin from there (on a cubieboard2).
You're right... I did spot this, but assumed this was my own mistake in merging
these patches with our 4.0RC7 tree. Sorry, could have saved you some trouble if
I were sharper.
I've also tried to get this code running on a cubieboard (non 2 so A10 rather
then
A20), the SPL loads fine there (indicating that the kernel bits work), but then
I get:
U-Boot SPL 2015.07-rc1-00287-g050de86-dirty (May 25 2015 - 22:28:19)
DRAM: 1024 MiB
CPU: 1008000000Hz, AXI/AHB/APB: 3/2/2
Nand initialised
NAND timeout reading data
NAND timeout reading data
NAND timeout reading data
NAND timeout reading data
NAND timeout reading data
NAND timeout reading data
...
Thanks for testing this. I don't own an A10 myself, so I haven't observed this
behaviour.
First thing I would verify personally is whether all the clocks are properly configured.
Could you make U-boot print &ccm->ahb_gate0 and &ccm->nand0_clk_cfg? For the
first, bits 6 (DMA) and 13 (NAND) must be set, the second must have bit 31 set, bits 24 and
25 cleared (and otherwise, the accompanying PLL must be configured too... probably easier to
use the OSC24M), and the divide ratios set to 0 (although a small divider, like 1, shouldn't
be a problem either).
I am assuming these values should be correct, but only because BROM initialised
part of it. I am aware of the fact that the SPL driver doesn't control the DMA
gating reg and the NAND post-dividers. It might be a good idea to do so for as
long as we don't have a full DMA driver, so I'll patch that up today.
I've just tried the prelimary v4 of your patch-set from:
https://gitlab.com/turtle-solutions/u-boot/commits/sunxi-nand-wip
And the changes you've made fix these errors on the A10, good job.
Regards,
Hans
--
You received this message because you are subscribed to the Google Groups
"linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
For more options, visit https://groups.google.com/d/optout.
