On 05/12/15 14:16, Chen-Yu Tsai wrote:
> The video engine has its own special module clock, consisting of a clock
> gate, configurable dividers, and a reset control.
>
Hi,
I've tested these patches on A20, everything works so far.
I only read some bits from a random bitstream, so nothing fancy yet, but
it shows that both dram and module clock are working.
One small indentation error below, otherwise it looks good.
> On later (sun[68]i) families, the reset control is moved out of this
> piece of hardware and grouped with reset controls of other peripherals.
>
> Signed-off-by: Chen-Yu Tsai <w...@csie.org>
> ---
> Documentation/devicetree/bindings/clock/sunxi.txt | 4 +
> drivers/clk/sunxi/Makefile | 1 +
> drivers/clk/sunxi/clk-a10-ve.c | 171
> ++++++++++++++++++++++
> 3 files changed, 176 insertions(+)
> create mode 100644 drivers/clk/sunxi/clk-a10-ve.c
>
> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt
> b/Documentation/devicetree/bindings/clock/sunxi.txt
> index ef0b452806b1..14496056319f 100644
> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
> @@ -74,6 +74,7 @@ Required properties:
> "allwinner,sun8i-h3-usb-clk" - for usb gates + resets on H3
> "allwinner,sun9i-a80-usb-mod-clk" - for usb gates + resets on A80
> "allwinner,sun9i-a80-usb-phy-clk" - for usb phy gates + resets on A80
> + "allwinner,sun4i-a10-ve-clk" - for the Video Engine clock
>
> Required properties for all clocks:
> - reg : shall be the control register address for the clock.
> @@ -93,6 +94,9 @@ Required properties for all clocks:
> And "allwinner,*-usb-clk" clocks also require:
> - reset-cells : shall be set to 1
>
> +The "allwinner,sun4i-a10-ve-clk" clock also requires:
> +- reset-cells : shall be set to 0
> +
> The "allwinner,sun9i-a80-mmc-config-clk" clock also requires:
> - #reset-cells : shall be set to 1
> - resets : shall be the reset control phandle for the mmc block.
> diff --git a/drivers/clk/sunxi/Makefile b/drivers/clk/sunxi/Makefile
> index 103efab05ca8..78db91ad5af6 100644
> --- a/drivers/clk/sunxi/Makefile
> +++ b/drivers/clk/sunxi/Makefile
> @@ -7,6 +7,7 @@ obj-y += clk-a10-codec.o
> obj-y += clk-a10-hosc.o
> obj-y += clk-a10-mod1.o
> obj-y += clk-a10-pll2.o
> +obj-y += clk-a10-ve.o
> obj-y += clk-a20-gmac.o
> obj-y += clk-mod0.o
> obj-y += clk-simple-gates.o
> diff --git a/drivers/clk/sunxi/clk-a10-ve.c b/drivers/clk/sunxi/clk-a10-ve.c
> new file mode 100644
> index 000000000000..de0fdb656150
> --- /dev/null
> +++ b/drivers/clk/sunxi/clk-a10-ve.c
> @@ -0,0 +1,171 @@
> +/*
> + * Copyright 2015 Chen-Yu Tsai
> + *
> + * Chen-Yu Tsai <w...@csie.org>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/clk-provider.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/reset-controller.h>
> +#include <linux/slab.h>
> +#include <linux/spinlock.h>
> +
> +static DEFINE_SPINLOCK(ve_lock);
> +
> +#define SUN4I_VE_ENABLE 31
> +#define SUN4I_VE_DIVIDER_SHIFT 16
> +#define SUN4I_VE_DIVIDER_WIDTH 3
> +#define SUN4I_VE_RESET 0
> +
> +/**
> + * sunxi_ve_reset... - reset bit in ve clk registers handling
> + */
> +
> +struct ve_reset_data {
> + void __iomem *reg;
> + spinlock_t *lock;
> + struct reset_controller_dev rcdev;
> +};
> +
> +static int sunxi_ve_reset_assert(struct reset_controller_dev *rcdev,
> + unsigned long id)
> +{
> + struct ve_reset_data *data = container_of(rcdev,
> + struct ve_reset_data,
> + rcdev);
> + unsigned long flags;
> + u32 reg;
> +
> + spin_lock_irqsave(data->lock, flags);
> +
> + reg = readl(data->reg);
> + writel(reg & ~BIT(SUN4I_VE_RESET), data->reg);
> +
> + spin_unlock_irqrestore(data->lock, flags);
> +
> + return 0;
> +}
> +
> +static int sunxi_ve_reset_deassert(struct reset_controller_dev *rcdev,
> + unsigned long id)
> +{
> + struct ve_reset_data *data = container_of(rcdev,
> + struct ve_reset_data,
> + rcdev);
> + unsigned long flags;
> + u32 reg;
> +
> + spin_lock_irqsave(data->lock, flags);
> +
> + reg = readl(data->reg);
> + writel(reg | BIT(SUN4I_VE_RESET), data->reg);
> +
> + spin_unlock_irqrestore(data->lock, flags);
> +
> + return 0;
> +}
> +
> +static int sunxi_ve_of_xlate(struct reset_controller_dev *rcdev,
> + const struct of_phandle_args *reset_spec)
> +{
> + if (WARN_ON(reset_spec->args_count != 0))
> + return -EINVAL;
> +
> + return 0;
^
Spaces instead of tabs here.
> +}
> +
> +static struct reset_control_ops sunxi_ve_reset_ops = {
> + .assert = sunxi_ve_reset_assert,
> + .deassert = sunxi_ve_reset_deassert,
> +};
> +
> +static void __init sun4i_ve_clk_setup(struct device_node *node)
> +{
> + struct clk *clk;
> + struct clk_divider *div;
> + struct clk_gate *gate;
> + struct ve_reset_data *reset_data;
> + const char *parent;
> + const char *clk_name = node->name;
> + void __iomem *reg;
> + int err;
> +
> + reg = of_io_request_and_map(node, 0, of_node_full_name(node));
> + if (IS_ERR(reg))
> + return;
> +
> + div = kzalloc(sizeof(*div), GFP_KERNEL);
> + if (!div)
> + goto err_unmap;
> +
> + gate = kzalloc(sizeof(*gate), GFP_KERNEL);
> + if (!gate)
> + goto err_free_div;
> +
> + of_property_read_string(node, "clock-output-names", &clk_name);
> + parent = of_clk_get_parent_name(node, 0);
> +
> + gate->reg = reg;
> + gate->bit_idx = SUN4I_VE_ENABLE;
> + gate->lock = &ve_lock;
> +
> + div->reg = reg;
> + div->shift = SUN4I_VE_DIVIDER_SHIFT;
> + div->width = SUN4I_VE_DIVIDER_WIDTH;
> + div->lock = &ve_lock;
> +
> + clk = clk_register_composite(NULL, clk_name, &parent, 1,
> + NULL, NULL,
> + &div->hw, &clk_divider_ops,
> + &gate->hw, &clk_gate_ops,
> + CLK_SET_RATE_PARENT);
> + if (IS_ERR(clk))
> + goto err_free_gate;
> +
> + err = of_clk_add_provider(node, of_clk_src_simple_get, clk);
> + if (err)
> + goto err_unregister_clk;
> +
> + reset_data = kzalloc(sizeof(*reset_data), GFP_KERNEL);
> + if (!reset_data)
> + goto err_del_provider;
> +
> + reset_data->reg = reg;
> + reset_data->lock = &ve_lock;
> + reset_data->rcdev.nr_resets = 1;
> + reset_data->rcdev.ops = &sunxi_ve_reset_ops;
> + reset_data->rcdev.of_node = node;
> + reset_data->rcdev.of_xlate = sunxi_ve_of_xlate;
> + reset_data->rcdev.of_reset_n_cells = 0;
> + err = reset_controller_register(&reset_data->rcdev);
> + if (err)
> + goto err_free_reset;
> +
> + return;
> +
> +err_free_reset:
> + kfree(reset_data);
> +err_del_provider:
> + of_clk_del_provider(node);
> +err_unregister_clk:
> + clk_unregister(clk);
> +err_free_gate:
> + kfree(gate);
> +err_free_div:
> + kfree(div);
> +err_unmap:
> + iounmap(reg);
> +}
> +CLK_OF_DECLARE(sun4i_ve, "allwinner,sun4i-a10-ve-clk",
> + sun4i_ve_clk_setup);
>
--
You received this message because you are subscribed to the Google Groups
"linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to linux-sunxi+unsubscr...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
