[linux-sunxi] [PATCH 09/11] ARM: dts: sun9i: cubieboard4: Add AXP809 PMIC device node and regulators

Tue, 02 Feb 2016 02:29:19 -0800 

The AXP809 PMIC is the primary PMIC. It provides various supply voltages
for the SoC and other peripherals. The PMIC's interrupt line is connected
to NMI pin of the SoC.

Signed-off-by: Chen-Yu Tsai <[email protected]>
---
 arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 121 +++++++++++++++++++++++++++-
 1 file changed, 119 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts 
b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
index eb2ccd0a3bd5..4d56dc69713c 100644
--- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
@@ -98,7 +98,7 @@
 &mmc0 {
        pinctrl-names = "default";
        pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_cubieboard4>;
-       vmmc-supply = <&reg_vcc3v0>;
+       vmmc-supply = <&reg_dcdc1>;
        bus-width = <4>;
        cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH18 */
        cd-inverted;
@@ -108,7 +108,7 @@
 &mmc2 {
        pinctrl-names = "default";
        pinctrl-0 = <&mmc2_8bit_pins>;
-       vmmc-supply = <&reg_vcc3v0>;
+       vmmc-supply = <&reg_dcdc1>;
        bus-width = <8>;
        non-removable;
        cap-mmc-hw-reset;
@@ -126,6 +126,123 @@
 
 &r_rsb {
        status = "okay";
+
+       axp809: pmic@3a3 {
+               reg = <0x3a3>;
+               interrupt-parent = <&nmi_intc>;
+               interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+       };
+};
+
+#include "axp809.dtsi"
+
+&reg_aldo1 {
+       /* TODO: This should be handled by the USB PHY driver */
+       regulator-always-on;
+       regulator-min-microvolt = <3000000>;
+       regulator-max-microvolt = <3000000>;
+       regulator-name = "vcc33-usbh";
+};
+
+&reg_aldo2 {
+       regulator-min-microvolt = <1800000>;
+       regulator-max-microvolt = <1800000>;
+       regulator-name = "vcc-pb-io-cam";
+};
+
+&reg_dc5ldo {
+       regulator-always-on;
+       regulator-min-microvolt = <800000>;
+       regulator-max-microvolt = <1100000>;
+       regulator-name = "vdd-cpus-09-usbh";
+};
+
+&reg_dcdc1 {
+       regulator-always-on;
+       regulator-min-microvolt = <3000000>;
+       regulator-max-microvolt = <3000000>;
+       regulator-name = "vcc-3v";
+};
+
+&reg_dcdc2 {
+       regulator-min-microvolt = <800000>;
+       regulator-max-microvolt = <1100000>;
+       regulator-name = "vdd-gpu";
+};
+
+&reg_dcdc3 {
+       regulator-always-on;
+       regulator-min-microvolt = <800000>;
+       regulator-max-microvolt = <1100000>;
+       regulator-name = "vdd-cpua";
+};
+
+&reg_dcdc4 {
+       regulator-always-on;
+       regulator-min-microvolt = <800000>;
+       regulator-max-microvolt = <1100000>;
+       regulator-name = "vdd-sys-usb0-hdmi";
+};
+
+&reg_dcdc5 {
+       regulator-always-on;
+       regulator-min-microvolt = <1425000>;
+       regulator-max-microvolt = <1575000>;
+       regulator-name = "vcc-dram";
+};
+
+&reg_dldo1 {
+       /*
+        * The WiFi chip supports a wide range (3.0 ~ 4.8V) of voltages,
+        * and so does this regulator (3.0 ~ 4.2V), but Allwinner SDK
+        * always sets it to 3.3V.
+        */
+       regulator-min-microvolt = <3300000>;
+       regulator-max-microvolt = <3300000>;
+       regulator-name = "vcc-wifi";
+};
+
+&reg_dldo2 {
+       regulator-always-on;
+       regulator-min-microvolt = <3000000>;
+       regulator-max-microvolt = <3000000>;
+       regulator-name = "vcc-pl";
+};
+
+&reg_eldo1 {
+       regulator-min-microvolt = <1200000>;
+       regulator-max-microvolt = <1200000>;
+       regulator-name = "vcc-dvdd-cam";
+};
+
+&reg_eldo2 {
+       regulator-min-microvolt = <1800000>;
+       regulator-max-microvolt = <1800000>;
+       regulator-name = "vcc-pe";
+};
+
+&reg_eldo3 {
+       regulator-always-on;
+       regulator-min-microvolt = <3000000>;
+       regulator-max-microvolt = <3000000>;
+       regulator-name = "vcc-pm-codec-io1";
+};
+
+&reg_ldo_io0 {
+       regulator-always-on;
+       regulator-min-microvolt = <3000000>;
+       regulator-max-microvolt = <3000000>;
+       regulator-name = "vcc-pg";
+};
+
+&reg_ldo_io1 {
+       regulator-min-microvolt = <2500000>;
+       regulator-max-microvolt = <2500000>;
+       regulator-name = "vcc-pa-gmac-2v5";
+};
+
+&reg_rtc_ldo {
+       regulator-name = "vcc-rtc-vdd1v8-io";
 };
 
 &uart0 {
-- 
2.7.0

-- 
You received this message because you are subscribed to the Google Groups 
"linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to [email protected].
For more options, visit https://groups.google.com/d/optout.

Reply via email to