Hi everyone, I just gotta a CubieTruck (Cubie V3) with the AA chip that doesn't boot.
The front leds doesn't show anything. I found a bad rtc battery, so took it out. After it I actually got some "reset" reseting the red led and power-on activity from the button. So... Nothing displayed at the Monitor (tryed HDMI and VGA with a SDCard and without it) Here is my USART debug: HELLO! BOOT0 is starting! boot0 version : 2.0.0˜ read dram para. dram driver version: 1.15 dram size =2048MB 0xffffffff super_standby_flag = 0 Succeed in opening nand flash. block from 2 to 6 deal block 2 Succeed in reading Boot1 file head. The size of Boot1 is 0x00068000. The file stored in 0x00000000 of block 2 is perfect. Check is correct. Ready to disable icache. Succeed in loading Boot1. Jump to Boot1. [ 0.147] boot1 version : 2.0.0 [ 0.156] script installed early ok [ 0.156] pmu type = 3 [ 0.158] bat vol = 1600 mv [ 0.174] axi:ahb:apb=4:2:2 [ 0.174] set dcdc2=1400mv, clock=912M successed [ 0.176] key [ 0.189] no key found [ 0.189] flash init start [ 0.189] NB1 : enter NFB_Init [ 0.192] NB1 : enter phy init [ 0.195] [NAND] nand driver(b) version: 0x0x00000002, 0x0x00000012, data: 0x20130325 [ 0.205] get the good blk ratio from hwscan : 912 [ 0.208] NB1 : nand phy init ok [ 0.317] NB1 : init ok [ 0.317] flash init finish [ 0.318] mbr magic is not correct [ 0.320] fs init fail [ 0.323] fs init fail, jump to fel HELLO! BOOT0 is starting! boot0 version : 2.0.0˜ read dram para. dram driver version: 1.15 dram size =2048MB 0xffffffff super_standby_flag = 0 Succeed in opening nand flash. block from 2 to 6 deal block 2 Succeed in reading Boot1 file head. The size of Boot1 is 0x00068000. The file stored in 0x00000000 of block 2 is perfect. Check is correct. Ready to disable icache. Succeed in loading Boot1. Jump to Boot1. [ 0.147] boot1 version : 2.0.0 [ 0.156] script installed early ok [ 0.156] pmu type = 3 [ 0.158] bat vol = 0 mv [ 0.174] axi:ahb:apb=4:2:2 [ 0.174] set dcdc2=1400mv, clock=912M successed [ 0.176] key [ 0.188] no key found [ 0.188] flash init start [ 0.188] NB1 : enter NFB_Init [ 0.191] NB1 : enter phy init [ 0.194] [NAND] nand driver(b) version: 0x0x00000002, 0x0x00000012, data: 0x20130325 [ 0.204] get the good blk ratio from hwscan : 912 [ 0.207] NB1 : nand phy init ok [ 0.316] NB1 : init ok [ 0.316] flash init finish [ 0.317] mbr magic is not correct [ 0.319] fs init fail [ 0.322] fs init fail, jump to fel How can I repair this? regards, Felipe -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
