Add explanations on where the options to pass to the tool should be
extracted from, and add two examples to illustrate this explanation.
Signed-off-by: Boris Brezillon <boris.brezil...@free-electrons.com>
---
Changes since v1:
- use shorter option names
- rework the help context
---
nand-image-builder.c | 67 ++++++++++++++++++++++++++++++++++++----------------
1 file changed, 47 insertions(+), 20 deletions(-)
diff --git a/nand-image-builder.c b/nand-image-builder.c
index 465ab36..98c0a82 100644
--- a/nand-image-builder.c
+++ b/nand-image-builder.c
@@ -917,21 +917,48 @@ static void display_help(int status)
{
fprintf(status == EXIT_SUCCESS ? stdout : stderr,
"Usage: sunxi-nand-image-builder [OPTIONS] source-image
output-image\n"
+ "\n"
"Creates a raw NAND image that can be read by the sunxi NAND
controller.\n"
"\n"
- "-h --help Display
this help and exit\n"
- "-c <strength>/<step> --ecc=<strength>/<step> ECC
config\n"
- " Valid
strengths: 16, 24, 28, 32, 40, 48, 56, 60 and 64\n"
- " Valid
steps: 512 and 1024\n"
- "-p <size> --page-size=<size> Page
size\n"
- "-o <size> --oob-size=<size> OOB
size\n"
- "-u <size> --usable-page-size=<size> Usable
page size. Only needed for boot0 mode\n"
- "-e <size> --eraseblock-size=<size> Erase
block size\n"
- "-b --boot0 Build a
boot0 image.\n"
- "-s --scramble
Scramble data\n"
- "-a <offset> --address Where
the image will be programmed.\n"
- " This
option is only required for non boot0 images that are meant to be programmed at
a non eraseblock aligned offset.\n"
- "\n");
+ " -h --help Display this
help and exit\n"
+ " -c <strength>/<step> --ecc=<strength>/<step> ECC config\n"
+ " Valid
strengths: 16, 24, 28, 32, 40, 48, 56, 60 and 64\n"
+ " Valid steps:
512 and 1024\n"
+ " -p <size> --page=<size> Page size\n"
+ " -o <size> --oob=<size> OOB size\n"
+ " -u <size> --usable=<size> Usable page
size. Only needed for boot0 mode\n"
+ " -e <size> --eraseblock=<size> Erase block
size\n"
+ " -b --boot0 Build a boot0
image.\n"
+ " -s --scramble Scramble data\n"
+ " -a <offset> --address Where the image
will be programmed.\n"
+ "\n"
+ "Notes:\n"
+ " All the information you need to pass to this tool should be
part of the NAND datasheet.\n"
+ "\n"
+ " If you are building a boot0 image, you'll have specify extra
options.\n"
+ " These options should be chosen based on the layouts described
here:\n"
+ " http://linux-sunxi.org/NAND#More_information_on_BROM_NAND\n";
+ "\n"
+ " --usable should be assigned the 'Hardware page' value\n"
+ " --ecc should be assigned the 'ECC capacity'/'ECC page'
values\n"
+ " --usable should be smaller than --page\n"
+ "\n"
+ " The --address option is only required for non-boot0 images
that are meant to be\n"
+ " programmed at a non eraseblock aligned offset.\n"
+ "\n"
+ "Examples:\n"
+ " The H27UCG8T2BTR-BC NAND exposes\n"
+ " * 16k pages\n"
+ " * 1280 OOB bytes per page\n"
+ " * 4M eraseblocks\n"
+ " * requires data scrambling\n"
+ " * expects a minimum ECC of 40bits/1024bytes\n"
+ "\n"
+ " A boot0 image can be generated with the following command\n"
+ " sunxi-nand-image-builder -p 16384 -o 1280 -e 0x400000
-s -b -u 4096 -c 64/1024\n"
+ " A normal image can be generated with\n"
+ " sunxi-nand-image-builder -p 16384 -o 1280 -e 0x400000
-s -c 40/1024\n"
+ );
exit(status);
}
@@ -942,17 +969,17 @@ static int check_image_info(struct image_info *info)
unsigned i;
if (!info->page_size) {
- fprintf(stderr, "--page-size is missing\n");
+ fprintf(stderr, "--page is missing\n");
return -EINVAL;
}
if (!info->page_size) {
- fprintf(stderr, "--oob-size is missing\n");
+ fprintf(stderr, "--oob is missing\n");
return -EINVAL;
}
if (!info->eraseblock_size) {
- fprintf(stderr, "--eraseblock-size is missing\n");
+ fprintf(stderr, "--eraseblock is missing\n");
return -EINVAL;
}
@@ -1004,10 +1031,10 @@ int main(int argc, char **argv)
static const struct option long_options[] = {
{"help", no_argument, 0, 0},
{"ecc", required_argument, 0, 'c'},
- {"page-size", required_argument, 0, 'p'},
- {"oob-size", required_argument, 0, 'o'},
- {"usable-page-size", required_argument, 0, 'u'},
- {"eraseblock-size", required_argument, 0, 'e'},
+ {"page", required_argument, 0, 'p'},
+ {"oob", required_argument, 0, 'o'},
+ {"usable", required_argument, 0, 'u'},
+ {"eraseblock", required_argument, 0, 'e'},
{"boot0", no_argument, 0, 'b'},
{"scramble", no_argument, 0, 's'},
{"address", required_argument, 0, 'a'},
--
2.7.4
--
You received this message because you are subscribed to the Google Groups
"linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to linux-sunxi+unsubscr...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
