[linux-sunxi] [PATCH 7/8] ARM: sun8i: a83t: cubietruck-plus: Enable onboard USB peripherals

[Chen-Yu Tsai]

The Cubietruck-plus has a GL830 USB-to-SATA bridge connected to EHCI0,
and a USB3503 HSIC USB 2.0 hub connected to EHCI1. The USB3503's I2C
control interface is not connected.

This patch enables both EHCI controllers, adds a device node for the
USB hub, and includes sunxi-common-regulators.dtsi for the VBUS
regulators. The existing reg_vcc3v3 is dropped as it is also available
in the set of common regulators. Other unused regulators are disabled.

Signed-off-by: Chen-Yu Tsai <w...@csie.org>
---
 arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts | 49 +++++++++++++++++++++---
 1 file changed, 44 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts 
b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
index f583e5b9a1c8..716a205c6dbb 100644
--- a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
+++ b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
@@ -44,6 +44,7 @@
 
 /dts-v1/;
 #include "sun8i-a83t.dtsi"
+#include "sunxi-common-regulators.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
 
@@ -83,11 +84,15 @@
                };
        };
 
-       reg_vcc3v3: vcc3v3 {
-               compatible = "regulator-fixed";
-               regulator-name = "vcc3v3";
-               regulator-min-microvolt = <3300000>;
-               regulator-max-microvolt = <3300000>;
+       usb-hub {
+               /* I2C is not connected */
+               compatible = "smsc,usb3503";
+               initial-mode = <1>; /* initialize in HUB mode */
+               disabled-ports = <1>;
+               intn-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+               reset-gpios = <&pio 4 16 GPIO_ACTIVE_HIGH>; /* PE16 */
+               connect-gpios = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
+               refclk-frequency = <19200000>;
        };
 
        sound {
@@ -109,6 +114,16 @@
        };
 };
 
+&ehci0 {
+       /* GL830 USB-to-SATA bridge here */
+       status = "okay";
+};
+
+&ehci1 {
+       /* USB3503 HSIC USB 2.0 hub here */
+       status = "okay";
+};
+
 &mmc0 {
        pinctrl-names = "default";
        pinctrl-0 = <&mmc0_pins>;
@@ -164,6 +179,24 @@
        };
 };
 
+&reg_usb1_vbus {
+       gpio = <&pio 3 29 GPIO_ACTIVE_HIGH>; /* PD29 */
+       status = "okay";
+};
+
+&reg_usb2_vbus {
+       gpio = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+       status = "okay";
+};
+
+&reg_vcc3v0 {
+       status = "disabled";
+};
+
+&reg_vcc5v0 {
+       status = "disabled";
+};
+
 &spdif {
        status = "okay";
 };
@@ -173,3 +206,9 @@
        pinctrl-0 = <&uart0_pb_pins>;
        status = "okay";
 };
+
+&usbphy {
+       usb1_vbus-supply = <&reg_usb1_vbus>;
+       usb2_vbus-supply = <&reg_usb2_vbus>;
+       status = "okay";
+};
-- 
2.13.3

-- 
You received this message because you are subscribed to the Google Groups 
"linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to linux-sunxi+unsubscr...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.