The Orange Pi Zero Plus has an additional LED that was missing from the device tree, and the power sequence for the SDIO Wi-Fi was missing.
The board also has UARTs 1, 2, and 3 exposed on a 26-pin GPIO header. As the header is not populated by the manufacturer, disable the UARTs by default. Additionally, fix up an incorrect comment, remove an unnecessary header inclusion, sort existing nodes, and fix some indentation issues. Signed-off-by: Samuel Holland <sam...@sholland.org> --- .../dts/allwinner/sun50i-h5-orangepi-zero-plus.dts | 58 ++++++++++++++++------ 1 file changed, 42 insertions(+), 16 deletions(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts index 1238de25a969..78edcb9d9167 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts @@ -10,23 +10,18 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> -#include <dt-bindings/pinctrl/sun4i-a10.h> / { model = "Xunlong Orange Pi Zero Plus"; compatible = "xunlong,orangepi-zero-plus", "allwinner,sun50i-h5"; - reg_vcc3v3: vcc3v3 { - compatible = "regulator-fixed"; - regulator-name = "vcc3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - aliases { ethernet0 = &emac; ethernet1 = &rtl8189ftv; serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; }; chosen { @@ -38,7 +33,7 @@ pwr { label = "orangepi:green:pwr"; - gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */ + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */ default-state = "on"; }; @@ -57,6 +52,18 @@ enable-active-high; gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */ }; + + reg_vcc3v3: vcc3v3 { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */ + }; }; &ehci0 { @@ -92,6 +99,7 @@ &mmc1 { vmmc-supply = <®_vcc3v3>; + mmc-pwrseq = <&wifi_pwrseq>; bus-width = <4>; non-removable; status = "okay"; @@ -105,7 +113,15 @@ }; }; -&spi0 { +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&spi0 { status = "okay"; flash@0 { @@ -117,18 +133,28 @@ }; }; -&ohci0 { +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; status = "okay"; }; -&ohci1 { - status = "okay"; +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + status = "disabled"; }; -&uart0 { +&uart2 { pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_a>; - status = "okay"; + pinctrl-0 = <&uart2_pins>; + status = "disabled"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; + status = "disabled"; }; &usb_otg { -- 2.16.1 -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscr...@googlegroups.com. For more options, visit https://groups.google.com/d/optout.