Three more variants of the Bananapi M2 Plus have been introduced. One with the H5 instead of the H3, another with the H2+ instead, and the last with the H3 but with WiFi and eMMC removed.
All these variants use the same board. This patch splits out the non-SoC-specific parts of the device tree, so that they can be shared among all the variants. The original Bananapi M2 Plus has been renamed to Bananapi M2 Plus H3. Signed-off-by: Chen-Yu Tsai <[email protected]> --- .../boot/dts/sun8i-h3-bananapi-m2-plus.dts | 190 +----------------- ...2-plus.dts => sunxi-bananapi-m2-plus.dtsi} | 5 - 2 files changed, 2 insertions(+), 193 deletions(-) copy arch/arm/boot/dts/{sun8i-h3-bananapi-m2-plus.dts => sunxi-bananapi-m2-plus.dtsi} (97%) diff --git a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts index bdda0d99128e..195a75da13f1 100644 --- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts +++ b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts @@ -42,195 +42,9 @@ /dts-v1/; #include "sun8i-h3.dtsi" -#include "sunxi-common-regulators.dtsi" - -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/input/input.h> +#include "sunxi-bananapi-m2-plus.dtsi" / { - model = "Banana Pi BPI-M2-Plus"; + model = "Banana Pi BPI-M2-Plus H3"; compatible = "sinovoip,bpi-m2-plus", "allwinner,sun8i-h3"; - - aliases { - ethernet0 = &emac; - serial0 = &uart0; - serial1 = &uart1; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - connector { - compatible = "hdmi-connector"; - type = "a"; - - port { - hdmi_con_in: endpoint { - remote-endpoint = <&hdmi_out_con>; - }; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-names = "default"; - - pwr_led { - label = "bananapi-m2-plus:red:pwr"; - gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */ - default-state = "on"; - }; - }; - - gpio_keys { - compatible = "gpio-keys"; - pinctrl-names = "default"; - - sw4 { - label = "power"; - linux,code = <BTN_0>; - gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; - }; - }; - - reg_gmac_3v3: gmac-3v3 { - compatible = "regulator-fixed"; - regulator-name = "gmac-3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - startup-delay-us = <100000>; - enable-active-high; - gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; - }; - - wifi_pwrseq: wifi_pwrseq { - compatible = "mmc-pwrseq-simple"; - pinctrl-names = "default"; - reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */ - }; -}; - -&de { - status = "okay"; -}; - -&ehci0 { - status = "okay"; -}; - -&ehci1 { - status = "okay"; -}; - -&ehci2 { - status = "okay"; -}; - -&emac { - pinctrl-names = "default"; - pinctrl-0 = <&emac_rgmii_pins>; - phy-supply = <®_gmac_3v3>; - phy-handle = <&ext_rgmii_phy>; - phy-mode = "rgmii"; - - status = "okay"; -}; - -&external_mdio { - ext_rgmii_phy: ethernet-phy@1 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <1>; - }; -}; - -&hdmi { - status = "okay"; -}; - -&hdmi_out { - hdmi_out_con: endpoint { - remote-endpoint = <&hdmi_con_in>; - }; -}; - -&ir { - pinctrl-names = "default"; - pinctrl-0 = <&ir_pins_a>; - status = "okay"; -}; - -&mmc0 { - vmmc-supply = <®_vcc3v3>; - bus-width = <4>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ - status = "okay"; -}; - -&mmc1 { - vmmc-supply = <®_vcc3v3>; - vqmmc-supply = <®_vcc3v3>; - mmc-pwrseq = <&wifi_pwrseq>; - bus-width = <4>; - non-removable; - status = "okay"; - - brcmf: wifi@1 { - reg = <1>; - compatible = "brcm,bcm4329-fmac"; - interrupt-parent = <&pio>; - interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */ - interrupt-names = "host-wake"; - }; -}; - -&mmc2 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc2_8bit_pins>; - vmmc-supply = <®_vcc3v3>; - vqmmc-supply = <®_vcc3v3>; - bus-width = <8>; - non-removable; - status = "okay"; -}; - -&ohci0 { - status = "okay"; -}; - -&ohci1 { - status = "okay"; -}; - -&ohci2 { - status = "okay"; -}; - -®_usb0_vbus { - gpio = <&pio 3 11 GPIO_ACTIVE_HIGH>; /* PD11 */ - status = "okay"; -}; - -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_a>; - status = "okay"; -}; - -&uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; - status = "okay"; -}; - -&usb_otg { - dr_mode = "otg"; - status = "okay"; -}; - -&usbphy { - usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */ - usb0_vbus-supply = <®_usb0_vbus>; - /* USB host VBUS is on as long as VCC-IO is on */ - status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/boot/dts/sunxi-bananapi-m2-plus.dtsi similarity index 97% copy from arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts copy to arch/arm/boot/dts/sunxi-bananapi-m2-plus.dtsi index bdda0d99128e..b3283aeb5b7d 100644 --- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts +++ b/arch/arm/boot/dts/sunxi-bananapi-m2-plus.dtsi @@ -40,17 +40,12 @@ * OTHER DEALINGS IN THE SOFTWARE. */ -/dts-v1/; -#include "sun8i-h3.dtsi" #include "sunxi-common-regulators.dtsi" #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> / { - model = "Banana Pi BPI-M2-Plus"; - compatible = "sinovoip,bpi-m2-plus", "allwinner,sun8i-h3"; - aliases { ethernet0 = &emac; serial0 = &uart0; -- 2.18.0 -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
