vcc-supply property is need for some Goodix CTP controller like GT5663 where 3.3V external pull-up regulator connected via controller VCC pin.
So, enable the regulator for those it attached the vcc-supply. Signed-off-by: Jagan Teki <[email protected]> --- drivers/input/touchscreen/goodix.c | 39 ++++++++++++++++++++++++++---- 1 file changed, 34 insertions(+), 5 deletions(-) diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c index f2d9c2c41885..7adcf1491609 100644 --- a/drivers/input/touchscreen/goodix.c +++ b/drivers/input/touchscreen/goodix.c @@ -27,6 +27,7 @@ #include <linux/delay.h> #include <linux/irq.h> #include <linux/interrupt.h> +#include <linux/regulator/consumer.h> #include <linux/slab.h> #include <linux/acpi.h> #include <linux/of.h> @@ -47,6 +48,7 @@ struct goodix_ts_data { struct touchscreen_properties prop; unsigned int max_touch_num; unsigned int int_trigger_type; + struct regulator *vcc; struct gpio_desc *gpiod_int; struct gpio_desc *gpiod_rst; u16 id; @@ -58,6 +60,7 @@ struct goodix_ts_data { #define GOODIX_GPIO_INT_NAME "irq" #define GOODIX_GPIO_RST_NAME "reset" +#define GOODIX_VCC_CTP_NAME "vcc" #define GOODIX_MAX_HEIGHT 4096 #define GOODIX_MAX_WIDTH 4096 @@ -525,12 +528,24 @@ static int goodix_get_gpio_config(struct goodix_ts_data *ts) { int error; struct device *dev; + struct regulator *regulator; struct gpio_desc *gpiod; if (!ts->client) return -EINVAL; dev = &ts->client->dev; + regulator = devm_regulator_get(dev, GOODIX_VCC_CTP_NAME); + if (IS_ERR(regulator)) { + error = PTR_ERR(regulator); + if (error != -EPROBE_DEFER) + dev_err(dev, "Failed to get vcc regulator: %d\n", + error); + return error; + } + + ts->vcc = regulator; + /* Get the interrupt GPIO pin number */ gpiod = devm_gpiod_get_optional(dev, GOODIX_GPIO_INT_NAME, GPIOD_IN); if (IS_ERR(gpiod)) { @@ -786,25 +801,34 @@ static int goodix_ts_probe(struct i2c_client *client, if (error) return error; + /* power the controller */ + if (ts->vcc) { + error = regulator_enable(ts->vcc); + if (error) { + dev_err(&client->dev, "Controller fail to enable vcc\n"); + return error; + } + } + if (ts->gpiod_int && ts->gpiod_rst) { /* reset the controller */ error = goodix_reset(ts); if (error) { dev_err(&client->dev, "Controller reset failed.\n"); - return error; + goto error; } } error = goodix_i2c_test(client); if (error) { dev_err(&client->dev, "I2C communication failure: %d\n", error); - return error; + goto error; } error = goodix_read_version(ts); if (error) { dev_err(&client->dev, "Read version failed.\n"); - return error; + goto error; } ts->chip = goodix_get_chip_data(ts->id); @@ -823,17 +847,22 @@ static int goodix_ts_probe(struct i2c_client *client, dev_err(&client->dev, "Failed to invoke firmware loader: %d\n", error); - return error; + goto error; } return 0; } else { error = goodix_configure_dev(ts); if (error) - return error; + goto error; } return 0; + +error: + if (ts->vcc) + regulator_disable(ts->vcc); + return error; } static int goodix_ts_remove(struct i2c_client *client) -- 2.18.0.321.gffc6fa0e3 -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
