From: Icenowy Zheng <[email protected]> TERES-I has an ANX6345 bridge connected to the RGB666 LCD output and eDP panel input. The bridge is controlled via I2C that's connected to I2C0 bus.
Enable all this hardware in device tree. Signed-off-by: Icenowy Zheng <[email protected]> Signed-off-by: Vasily Khoruzhick <[email protected]> --- .../boot/dts/allwinner/sun50i-a64-teres-i.dts | 71 +++++++++++++++++-- 1 file changed, 67 insertions(+), 4 deletions(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts index c455b24dd079..6c4090f59bed 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts @@ -56,6 +56,17 @@ }; }; + edp_panel: edp-panel { + compatible = "panel-edp", "simple-panel"; + + port { + panel_in_edp: endpoint { + remote-endpoint = <&anx6345_out_panel>; + }; + }; + }; + + reg_usb1_vbus: usb1-vbus { compatible = "regulator-fixed"; regulator-name = "usb1-vbus"; @@ -72,20 +83,58 @@ }; }; +&de { + status = "okay"; +}; + &ehci1 { status = "okay"; }; -/* The ANX6345 eDP-bridge is on i2c0. There is no linux (mainline) - * driver for this chip at the moment, the bootloader initializes it. - * However it can be accessed with the i2c-dev driver from user space. - */ &i2c0 { clock-frequency = <100000>; pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins>; status = "okay"; + + anx6345: anx6345@38 { + compatible = "analogix,anx6345"; + reg = <0x38>; + reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */ + dvdd25-supply = <®_dldo2>; + dvdd12-supply = <®_dldo3>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + anx6345_in: port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + anx6345_in_tcon0: endpoint@0 { + reg = <0>; + remote-endpoint = <&tcon0_out_anx6345>; + }; + }; + + anx6345_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + anx6345_out_panel: endpoint@0 { + reg = <0>; + remote-endpoint = <&panel_in_edp>; + }; + }; + }; + }; +}; + +&mixer0 { + status = "okay"; }; &mmc0 { @@ -258,6 +307,20 @@ vcc-hdmi-supply = <®_dldo1>; }; +&tcon0 { + pinctrl-names = "default"; + pinctrl-0 = <&lcd_rgb666_pins>; + + status = "okay"; +}; + +&tcon0_out { + tcon0_out_anx6345: endpoint@0 { + reg = <0>; + remote-endpoint = <&anx6345_in_tcon0>; + }; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pb_pins>; -- 2.20.1 -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
