A new variant of Emlid Neutis has been inroduced. This one uses H3 instead of H5. The boards are essentially the same. This commit moves non-SoC-specific parts out so that the common parts could be reused with ease.
Signed-off-by: Georgii Staroselskii <[email protected]> --- arch/arm/boot/dts/sunxi-h3-h5-emlid-neutis.dtsi | 170 +++++++++++++++++++++ .../sun50i-h5-emlid-neutis-n5-devboard.dts | 95 +----------- .../dts/allwinner/sun50i-h5-emlid-neutis-n5.dtsi | 64 +------- 3 files changed, 175 insertions(+), 154 deletions(-) create mode 100644 arch/arm/boot/dts/sunxi-h3-h5-emlid-neutis.dtsi diff --git a/arch/arm/boot/dts/sunxi-h3-h5-emlid-neutis.dtsi b/arch/arm/boot/dts/sunxi-h3-h5-emlid-neutis.dtsi new file mode 100644 index 00000000..fc67e30 --- /dev/null +++ b/arch/arm/boot/dts/sunxi-h3-h5-emlid-neutis.dtsi @@ -0,0 +1,170 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * DTSI for Emlid Neutis SoMs. + * + * Copyright (C) 2019 Georgii Staroselskii <[email protected]> + */ + +#include "sunxi-common-regulators.dtsi" + +#include <dt-bindings/gpio/gpio.h> + +/ { + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&pio 2 7 GPIO_ACTIVE_LOW>; /* PC7 */ + post-power-on-delay-ms = <200>; + clocks = <&rtc 1>; + clock-names = "ext_clock"; + }; +}; + +&cpu0 { + cpu-supply = <&vdd_cpux>; +}; + +®_usb0_vbus { + gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */ + status = "okay"; +}; + + +&de { + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&ohci2 { + status = "okay"; +}; + +&ohci3 { + status = "okay"; +}; + + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&ehci2 { + status = "okay"; +}; + +&ehci3 { + status = "okay"; +}; + +&mmc0 { + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + status = "okay"; +}; + + +&mmc1 { + vmmc-supply = <®_vcc3v3>; + vqmmc-supply = <®_vcc3v3>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <&r_pio>; + interrupts = <0 5 IRQ_TYPE_LEVEL_LOW>; /* PL5 */ + interrupt-names = "host-wake"; + }; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_8bit_pins>; + vmmc-supply = <®_vcc3v3>; + bus-width = <8>; + non-removable; + cap-mmc-hw-reset; + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pa_pins>; + status = "okay"; +}; + + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; + uart-has-rtscts; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + clocks = <&rtc 1>; + clock-names = "lpo"; + vbat-supply = <®_vcc3v3>; + vddio-supply = <®_vcc3v3>; + shutdown-gpios = <&pio 2 4 GPIO_ACTIVE_HIGH>; /* PC4 */ + device-wakeup-gpios = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */ + }; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; + status = "okay"; +}; + +&usbphy { + usb0_id_det-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ + usb0_vbus-supply = <®_usb0_vbus>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&codec { + allwinner,audio-routing = + "Line Out", "LINEOUT", + "LINEIN", "Line In", + "MIC1", "Mic", + "MIC2", "Mic", + "Mic", "MBIAS"; +}; + +&i2c0 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5-devboard.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5-devboard.dts index c924090..fb96d35 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5-devboard.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5-devboard.dts @@ -15,35 +15,6 @@ "emlid,neutis-n5", "allwinner,sun50i-h5"; - aliases { - serial0 = &uart0; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - connector { - compatible = "hdmi-connector"; - type = "a"; - - port { - hdmi_con_in: endpoint { - remote-endpoint = <&hdmi_out_con>; - }; - }; - }; - - reg_usb0_vbus: usb0-vbus { - compatible = "regulator-fixed"; - regulator-name = "usb0-vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */ - status = "okay"; - }; - vdd_cpux: gpio-regulator { compatible = "regulator-gpio"; regulator-name = "vdd-cpux"; @@ -59,33 +30,11 @@ }; }; -&codec { - allwinner,audio-routing = - "Line Out", "LINEOUT", - "LINEIN", "Line In", - "MIC1", "Mic", - "MIC2", "Mic", - "Mic", "MBIAS"; - status = "okay"; -}; - -&de { - status = "okay"; -}; - -&ehci0 { - status = "okay"; -}; - -&ehci1 { - status = "okay"; -}; - -&ehci2 { - status = "okay"; +&cpu0 { + cpu-supply = <&vdd_cpux>; }; -&ehci3 { +&codec { status = "okay"; }; @@ -106,42 +55,6 @@ }; }; -&mmc0 { - vmmc-supply = <®_vcc3v3>; - bus-width = <4>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ - status = "okay"; -}; - -&ohci0 { - status = "okay"; -}; - -&ohci1 { - status = "okay"; -}; - -&ohci2 { - status = "okay"; -}; - -&ohci3 { - status = "okay"; -}; - -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_pa_pins>; - status = "okay"; -}; - -&usb_otg { - dr_mode = "otg"; - status = "okay"; -}; - -&usbphy { - usb0_id_det-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ - usb0_vbus-supply = <®_usb0_vbus>; +&i2c1 { status = "okay"; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5.dtsi index 5bec574..7df7308 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5.dtsi @@ -8,66 +8,4 @@ /dts-v1/; #include "sun50i-h5.dtsi" - -#include <dt-bindings/gpio/gpio.h> - -/ { - reg_vcc3v3: vcc3v3 { - compatible = "regulator-fixed"; - regulator-name = "vcc3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - wifi_pwrseq: wifi_pwrseq { - compatible = "mmc-pwrseq-simple"; - reset-gpios = <&pio 2 7 GPIO_ACTIVE_LOW>; /* PC7 */ - post-power-on-delay-ms = <200>; - clocks = <&rtc 1>; - clock-names = "ext_clock"; - }; -}; - -&mmc1 { - vmmc-supply = <®_vcc3v3>; - vqmmc-supply = <®_vcc3v3>; - mmc-pwrseq = <&wifi_pwrseq>; - bus-width = <4>; - non-removable; - status = "okay"; - - brcmf: wifi@1 { - reg = <1>; - compatible = "brcm,bcm4329-fmac"; - interrupt-parent = <&r_pio>; - interrupts = <0 5 IRQ_TYPE_LEVEL_LOW>; /* PL5 */ - interrupt-names = "host-wake"; - }; -}; - -&mmc2 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc2_8bit_pins>; - vmmc-supply = <®_vcc3v3>; - bus-width = <8>; - non-removable; - cap-mmc-hw-reset; - status = "okay"; -}; - -&uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; - uart-has-rtscts; - status = "okay"; - - bluetooth { - compatible = "brcm,bcm43438-bt"; - clocks = <&rtc 1>; - clock-names = "lpo"; - vbat-supply = <®_vcc3v3>; - vddio-supply = <®_vcc3v3>; - shutdown-gpios = <&pio 2 4 GPIO_ACTIVE_HIGH>; /* PC4 */ - device-wakeup-gpios = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */ - }; -}; +#include <arm/sunxi-h3-h5-emlid-neutis.dtsi> -- 2.7.4 -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/1573575320-29546-2-git-send-email-georgii.staroselskii%40emlid.com.
