Hi Samuel,
On Sat, Feb 22, 2020 at 09:26:30PM -0600, Samuel Holland wrote:
> Hi Ondrej,
>
> On 2/22/20 3:45 PM, Ondrej Jirman wrote:
> > Orange Pi PC2 features sy8106a regulator just like Orange Pi PC.
> >
> > Signed-off-by: Ondrej Jirman <meg...@megous.com>
> > ---
> > .../dts/allwinner/sun50i-h5-orangepi-pc2.dts | 29 +++++++++++++++++++
> > 1 file changed, 29 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
> > b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
> > index 70b5f09984218..5feedde95b5fc 100644
> > --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
> > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
> > @@ -85,6 +85,10 @@ reg_usb0_vbus: usb0-vbus {
> > };
> > };
> >
> > +&cpu0 {
> > + cpu-supply = <®_vdd_cpux>;
> > +};
> > +
>
> This should go alphabetically after "codec".
>
> > &codec {
> > allwinner,audio-routing =
> > "Line Out", "LINEOUT",
> > @@ -180,6 +184,31 @@ flash@0 {
> > };
> > };
> >
> > +&r_i2c {
>
> This should go alphabetically before "spi0".
>
> > + status = "okay";
> > +
> > + reg_vdd_cpux: regulator@65 {
> > + compatible = "silergy,sy8106a";
> > + reg = <0x65>;
> > + regulator-name = "vdd-cpux";
> > + silergy,fixed-microvolt = <1200000>;
>
> The resistors in the datasheet (10k/11.8k) make this 1.1V.
Ah, you're right. I didn't notice the fine print bellow:
https://megous.com/dl/tmp/e696b6042b80bf2e.png
only the big number above. Hehe.
> > + /*
> > + * The datasheet uses 1.1V as the minimum value of VDD-CPUX,
> > + * however both the Armbian DVFS table and the official one
> > + * have operating points with voltage under 1.1V, and both
> > + * DVFS table are known to work properly at the lowest
> > + * operating point.
> > + *
> > + * Use 1.0V as the minimum voltage instead.
> > + */
>
> The datasheet I have for H5 has "TBD" for the VDD-CPUX volatage range. I think
> this comment only applies to H3 and is not necessary here.
Ok.
> > + regulator-min-microvolt = <1000000>;
> > + regulator-max-microvolt = <1400000>;
> > + regulator-ramp-delay = <200>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +};
> > +
> > &uart0 {
> > pinctrl-names = "default";
> > pinctrl-0 = <&uart0_pa_pins>;
> >
>
> Otherwise,
> Reviewed-by: Samuel Holland <sam...@sholland.org>
Thanks for the feedback.
regards,
o.
> Regards,
> Samuel
--
You received this message because you are subscribed to the Google Groups
"linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to linux-sunxi+unsubscr...@googlegroups.com.
To view this discussion on the web, visit
https://groups.google.com/d/msgid/linux-sunxi/20200223103736.5uigz2nvvee3w5yr%40core.my.home.
