I am trying again to get my External Ditto Tape Drive working, and have
downloaded ftape-4.03-pre-2.tar.gz from the home of ftape at
http://www.math1.rwth-aachen.de/%7Eheine/ftape/
When I try to <MAKE> , I am getting the following errors :-
gcc -Wall -Wstrict-prototypes -O2 -fomit-frame-pointer -fno-strength-reduce
-D__KERNEL__ -I. -I../../include -I/usr/src/linux/include -m386 -DCPU=386 -DMODULE -c
fdc-io.c
fdc-io.c: In function `fdc_interrupt_wait':
fdc-io.c:433: structure has no member named `timeout'
fdc-io.c:454: structure has no member named `timeout'
make[2]: *** [fdc-io.o] Error 1
make[2]: Leaving directory `/temp/ftape-4.03-pre-2/ftape/lowlevel'
make[1]: *** [modules] Error 2
make[1]: Leaving directory `/temp/ftape-4.03-pre-2/ftape'
make: *** [all] Error 2
...............................................................................................
I tried to continue, with <make install> and the result was that I got the
same messages about ~
fdc-io.c: In function `fdc_interrupt_wait':
fdc-io.c:433: structure has no member named `timeout'
fdc-io.c:454: structure has no member named `timeout'
*** [fdc-io.o] Error 1
Leaving directory `/temp/ftape-4.03-pre-2/ftape/lowlevel'
*** [modules] Error 2
Leaving directory `/temp/ftape-4.03-pre-2/ftape'
*** [all] Error 2
...............................................................................................
and, nothing got written to my /usr/src/linux-vers/lib/modules directory ?
What's to be done to fix this ?
Attached is my MCONFIG file .
Thanks
--
____________
sent on Linux
____________
###############################################################################
#
# Copyright (C) 1997-1999 Claus Heine.
#
# This program is free software; you can redistribute it and/or modify
# it under the terms of the GNU General Public License as published by
# the Free Software Foundation; either version 2, or (at your option)
# any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; see the file COPYING. If not, write to
# the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
#
# $RCSfile: MCONFIG,v $
# $Revision: 1.69 $
# $Date: 1999/03/28 21:51:26 $
#
# Compile time configuration for the QIC-40/80/3010/3020 ftape
# driver for Linux
#
###############################################################################
###############################################################################
#
# Pathnames. These should work just fine.
#
# change the following to point to the start of your kernel source tree:
#
# IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT
LINUX_LOCATION = /usr/src/linux
#
# Ok. It looks ugly. It is ugly.
#
KERNEL_VERSION = $(shell grep UTS_RELEASE $(LINUX_LOCATION)/include/linux/version.h|cut -d '"' -f 2)
#
# The following means that this package doesn't support
# cross-compilation. Stolen from Linux v2.2
#
ARCH := $(shell uname -m | sed -e s/i.86/i386/ -e s/sun4u/sparc64/ -e s/arm.*/arm/ -e s/sa110/arm/)
#
# Change the following to point to the directory where you want the
# modules to be installed.
#
MODULESDIR = /lib/modules/$(KERNEL_VERSION)/misc
#
###############################################################################
###############################################################################
# IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT #
###############################################################################
#
# Get the configuration of the kernel ftape is compiled for.
#
# This will only work with a configured kernel, but we need a fully
# configured kernel anyways?? If `$(LINUX_LOCATION)/.config' DOESN'T
# exist you'll need to set the variables of the "else" part of the
# "ifeq" clause according to the configuration of the kernel you want
# ftape to use with. If `$(LINUX_LOCATION)/.config' exists you can
# skip this part and go on with the hardware configuration options
# below.
#
#
ifeq ($(LINUX_LOCATION)/.config,$(wildcard $(LINUX_LOCATION)/.config))
include $(LINUX_LOCATION)/.config
else
#
# If the file `$(LINUX_LOCATION)/.config' doesn't exists, then try to
# tune the parameters in this "else" part of the "ifeq" clause above
# to fit your setup.
#
# If you attempt to use CONFIG_MODVERSIONS then make sure that
# `$(LINUX_LOCATION)/include/linux/modversions.h' REALLY
# EXISTS. Otherwise, don't use CONFIG_MODVERSIONS.
#
# You should also set the CONFIG_M386/486/586/686 according to your
# processor type. When running an DEC alpha then comment out the
# CONFIG_M486=y line and uncomment the CONFIG_ALPHA=y line.
#
#CONFIG_M386=y
#CONFIG_M486=y
CONFIG_M586=y
#CONFIG_M686=y
#CONFIG_MAMDK6
#CONFIG_ALPHA=y
#CONFIG_MODVERSIONS=y
#CONFIG_SMP = 1
#
# DON'T touch the following two lines! To enable/disable the procfs
# interface you should uncomment/comment out the CONFIG_FT_PROC_FS
# option below and leave the CONFIG_PROC_FS option ENABLED.
#
CONFIG_PROC_FS=y
CONFIG_MODULES=y
endif
#
###############################################################################
###############################################################################
# IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT #
###############################################################################
#
# You MUST uncomment the following line if you are running a SMP
# (multi-processor) system (unless you are unsing Linux v2.2 and MCONFIG
# has been given the correct location of you correctly configured kernel
# source tree ...)
#
#CONFIG_SMP = 1
#
###############################################################################
###############################################################################
# IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT #
###############################################################################
#
# Hardware configuration for the floppy tape drive.
#
# You need to take care of the following options if you didn't connect
# your floppy tape to the standard floppy controller, i.e. if you
# didn't plugged the floppy tape into the floppy controller already
# contained in your computer system.
#
# Short description of available options
# (`FDC' stands for `Floppy Disk Controller')
#
# PROBE_FC10 - if defined will look for a FC-10 (or FC-20)
# card.
# FDC_BASE - sets base address if using non-standard fdc
# FDC_IRQ - sets interrupt if FDC_BASE is defined
# FDC_DMA - sets dma channel if FDC_BASE is defined
# MACH2 - Support for Mountain MACH-2 controller. You
# have to specify its base address (either
# 0x1E0 or 0x3E0).
# CLK_48MHZ - must be defined and set to 0 if your 82078
# is _not_ being run from a 48 Mhz clock
# oscillator. Normally you don't need to worry
# about it.
#
#
#
# If you're using a non-standard floppy disk controller for the tape
# drive, enable one (only!) of the following lines and set the
# FDC_BASE, FDC_IRQ and FDC_DMA parameters to the actual values.
#
# `enable' means: `uncomment one of the lines starting with
# "FDC_OPT = ..."'. `uncomment' means: remove the leading `#'
#
# The following values hopefully reflect the default settings for
# those controllers.
#
# Note1: A FC-10/FC-20 controller must use either of DMA 1, 2, or 3.
# DMA 5 and 7 does NOT work!.
#
# Note2: IRQ 2 and IRQ 9 can be considered the same. When using IRQ 2
# on a controller you must specify IRQ 9 here!
#
# Note3: *_ALL_* parameters can as well be set as module parameters
# during module loading. This means that the following values
# only give the defaults in case you load the modules without
# any parameters.
#
# Note4: The "..._DEV=0" lines determine which device nodes to use
# with which floppy tape controller (/dev/qft0, ...,
# /dev/qft3). In case you have an internal floppy tape plugged
# into the standard floppy controller and a parallel port
# floppy tape drive, then leave the "STD_DEV=0" line as it is
# and uncomment either the option settings for the Trakker or
# the BackPack tape drive and set either "TRAKKER_DEV=1" or
# "BPCK_DEV=1" to use the parallel port tape drive using
# "/dev/qft1".
#
FDC_OPT :=
#
# For a standard floppy tape controller or automatic configuration of
# parallel port floppy tape drives uncomment the following line:
#
AUTO_DEV=0
#FDC_OPT += -DCONFIG_FT_STD_FDC_$(AUTO_DEV) \
-DCONFIG_FT_AUTO_$(AUTO_DEV)=1
#
# For a standard floppy tape controller, uncomment the following line:
#
STD_DEV=0
#FDC_OPT += -DCONFIG_FT_STD_FDC_$(STD_DEV) \
-DCONFIG_FT_INT_$(STD_DEV)=1
#
# For a Mountain MACH-2 controller, try
#
MACH2_DEV=0
#FDC_OPT += -DCONFIG_FT_MACH2_$(MACH2_DEV)=1 \
-DCONFIG_FT_FDC_BASE_$(MACH2_DEV)=0x1E0 \
-DCONFIG_FT_FDC_IRQ_$(MACH2_DEV)=6 \
-DCONFIG_FT_FDC_DMA_$(MACH2_DEV)=2 \
-DCONFIG_FT_NR_BUFFERS=3 \
-DCONFIG_FT_INT_$(MACH2_DEV)=1
#
# For Colorado CMS FC-10 or FC-20 controllers:
#
FC10_DEV=0
#FDC_OPT += -DCONFIG_FT_FC10_$(FC10_DEV)=1 \
-DCONFIG_FT_FDC_BASE_$(FC10_DEV)=0x180 \
-DCONFIG_FT_FDC_IRQ_$(FC10_DEV)=9 \
-DCONFIG_FT_FDC_DMA_$(FC10_DEV)=3 \
-DCONFIG_FT_NR_BUFFERS=3 \
-DCONFIG_FT_INT_$(FC10_DEV)=1
#
# Secondary floppy disk controller:
# including Ditto Dash 2Mbps controller, ExaByte accelerator card,
# CTC-2Mb (Seagate) and hopefully any 82078 based FDC controller card.
#
82078_DEV=0
#FDC_OPT = -DCONFIG_FT_FDC_BASE_$(82078_DEV)=0x370 \
-DCONFIG_FT_FDC_IRQ_$(82078_DEV)=6 \
-DCONFIG_FT_FDC_DMA_$(82078_DEV)=2 \
-DCONFIG_FT_NR_BUFFERS=3 \
-DCONFIG_FT_INT_$(82078_DEV)=1
#
# Maybe one of the following alternatives work if you have a Ditto
# Dash and the above setting doesn't work:
#
#FDC_OPT = -DCONFIG_FT_FDC_BASE_$(82078_DEV)=0x370 \
-DCONFIG_FT_FDC_IRQ_$(82078_DEV)=5 \
-DCONFIG_FT_FDC_DMA_$(82078_DEV)=3 \
-DCONFIG_FT_NR_BUFFERS=3 \
-DCONFIG_FT_INT_$(82078_DEV)=1
#FDC_OPT = -DCONFIG_FT_FDC_BASE_$(82078_DEV)=0x370 \
-DCONFIG_FT_FDC_IRQ_$(82078_DEV)=2 \
-DCONFIG_FT_FDC_DMA_$(82078_DEV)=3 \
-DCONFIG_FT_NR_BUFFERS=3 \
-DCONFIG_FT_INT_$(82078_DEV)=1
#
# For a HP Colorado Trakker parallel port drive, try
#
TRAKKER_DEV=0
#FDC_OPT += -DCONFIG_FT_FDC_PARPORT_$(TRAKKER_DEV)=-1 \
-DCONFIG_FT_PAR_$(TRAKKER_DEV)=1 \
-DCONFIG_FT_TRAKKER_$(TRAKKER_DEV)=1
#
# For a Micro Solutions opispo "backpack" based parallel port drive, try
#
BPCK_DEV=0
FDC_OPT += -DCONFIG_FT_FDC_PARPORT_$(BPCK_DEV)=-1 \
-DCONFIG_FT_PAR_$(BPCK_DEV)=1 \
-DCONFIG_FT_BPCK_$(BPCK_DEV)=1
#
#
#
#
###############################################################################
###############################################################################
#
# Generic ftape options.
#
# Valid ftape options are:
#
# GCC_2_4_5_BUG - must be set if using gcc-2.4.5 to prevent
# bad assembler-code for the dma
# handling. Type `gcc --version' to determine
# the version of gcc.
#
# CONFIG_FT_PROC_FS - enables proc interface (read-only) to provide
# information about kind of tape drive, data
# rate etc. Consumes about 2 kb of memory.
# Make sure to read the file `BUGS' before
# enabling this option. THIS WILL NOT WORK
# with Linux v1.2.13 (and older) kernels. It
# is safe to use this option with v2.1.x and
# later kernels
#
# BROKEN_FLOPPY_DRIVER - leave this defined if you DON'T apply the patch
# `patches/v2.0/floppy.c.dif' to the floppy
# driver of the standard kernel distribution.
# If you DON'T apply my patch, then you
# definitely need this switch if you want to
# create an emergency (rescue) disk with
# ftape. DON'T define this if you are running
# v2.1.x or later kernels. But if you are
# running v2.1.115 (maybe also v2.1.116) or
# previous kernels of the 2.1.x series, then
# consider applying the patch
# `patches/v2.1/floppy.c.dif' to your kernel.
# CONFIG_ZFT_DFLT_BLK_SZ - minimum IO block size of the tape devices.
# every read or write attempt must be a
# multiple of this many bytes. Default is 10k
# (block size used by tar). Many SCSI tapes
# use 32k. Allowed values are multiples of
# 1024 up to 62k. A value of "0" lets zftape
# use variable block size mode, i.e. every
# read/write operation must be a multiple of 1
# byte, i.e. arbitray block sizes are
# admissible. Compilation of the ftape
# modules will fail if this parameter isn't
# aligned to 1024 bytes.
#
FTAPE_OPT = -DTHE_FTAPE_MAINTAINER=\"[EMAIL PROTECTED]\"
#FTAPE_OPT += -DBROKEN_FLOPPY_DRIVER
FTAPE_OPT += -DCONFIG_FT_PROC_FS
#FTAPE_OPT += -DCONFIG_ZFT_DFLT_BLK_SZ=10240
#
###############################################################################
###############################################################################
#
# Options that affect the amount of debugging messages printed to the
# system console (or kernel log files). Also reduces the size of the
# driver.
#
# CONFIG_FT_FULL_DEBUG - if NOT defined, all messages with trace
# level 6 (i.e. ft_fdc_dma) or higher are
# disabled. You probably don't want to
# define this unless you want debug the
# drive. If unsure, don't define this.
#
# CONFIG_FT_NO_TRACE - if defined, only information and errors
# show up. If unsure, don't define it.
#
# CONFIG_FT_NO_TRACE_AT_ALL - if defined, no trace output shows
# up. If unsure, don't define it.
#
#TRACE_FLAGS = -DCONFIG_FT_NO_TRACE
#TRACE_FLAGS = -DCONFIG_FT_NO_TRACE_AT_ALL
#TRACE_FLAGS = -DCONFIG_FT_FULL_DEBUG
#
###############################################################################
###############################################################################
#
# Compiler options for your architecture
#
# ... in case you need any special options ...
#
# ARCH_OPT =
#
###############################################################################
###############################################################################
#
# Don't change anything below this point!!!!
#
# Unless you know what you are doing. Don't expect me to help you.
#
ifeq ($(CONFIG_MODULES),n)
ERROR_RULE:
@echo
@echo "*************************************************"
@echo
@echo "Please reconfigure your kernel to support runtime"
@echo "loadable modules. Retry making ftape afterwards."
@echo
@echo "*************************************************"
@echo
exit 1
endif
#
# MODVERSIONS and MODULES stuff
#
MAKING_MODULES = 1
MODULE_OPT = -DMODULE
ifeq ($(CONFIG_MODVERSIONS),y)
MODULE_OPT += -DMODVERSIONS
MODULE_OPT += -include $(TOPDIR)/include/linux/modftversions.h
GENKSYMS = /sbin/genksyms
endif
#
# assemble the compile time options
#
CONFIG_OPT := $(FTAPE_OPT) $(FDC_OPT) $(TRACE_FLAGS)
CONFIG_OPT += -DCONFIG_FTAPE_MODULE
CONFIG_OPT += -DCONFIG_FT_INTERNAL_MODULE
CONFIG_OPT += -DCONFIG_FT_PARPORT
CONFIG_OPT += -DCONFIG_FT_TRAKKER_MODULE
CONFIG_OPT += -DCONFIG_FT_BPCK_MODULE
CONFIG_OPT += -DCONFIG_ZFTAPE_MODULE
CONFIG_OPT += -DCONFIG_ZFT_COMPRESSOR_MODULE
override CONFIG_FTAPE := m
override CONFIG_FT_INTERNAL := m
override CONFIG_FT_PARPORT := m
override CONFIG_FT_TRAKKER := m
override CONFIG_FT_BPCK := m
override CONFIG_ZFTAPE := m
override CONFIG_ZFT_COMPRESSOR := m
ifneq ($(findstring, CONFIG_FT_PROC_FS,$(FTAPE_OPT)),"")
CONFIG_FT_PROC_FS := y
endif
#
# options needed to compile kernel source
#
WARNINGS := -Wall -Wstrict-prototypes
COMPILE := -O2 $(ARCH_OPT) -fomit-frame-pointer -fno-strength-reduce
LD_OPT := -r -S
INCLUDE_PATH := -I. -I$(TOPDIR)/include -I$(LINUX_LOCATION)/include
KERNEL_OPT := -D__KERNEL__ $(INCLUDE_PATH)
#
# The alpha needs this defined early.
#
CC = gcc
HOSTCC = gcc
#
# Linux v2.2 defines this via a configuration option (finally :-)
#
ifdef CONFIG_SMP
KERNEL_OPT += -D__SMP__
endif
#
# processor and architecture specific options.
#
ifeq (i386,$(ARCH))
ifdef CONFIG_M386
KERNEL_OPT += -m386 -DCPU=386
endif
ifdef CONFIG_M486
KERNEL_OPT += -m486 -DCPU=486
endif
ifdef CONFIG_M586
KERNEL_OPT += -m486 -malign-loops=2 -malign-jumps=2 -malign-functions=2 -DCPU=586
endif
ifdef CONFIG_M586TSC
KERNEL_OPT += -m486 -malign-loops=2 -malign-jumps=2 -malign-functions=2 -DCPU=586
endif
ifdef CONFIG_M686
KERNEL_OPT += -m486 -malign-loops=2 -malign-jumps=2 -malign-functions=2 -DCPU=686
endif
ifdef CONFIG_MAMDK6
KERNEL_OPT += -mamdk6 -frisc
endif
else # i386
ifeq (alpha,$(ARCH))
###############################################################################
#
# We start with options which apply to both, v2.0 and v2.2 kernels.
#
###############################################################################
#
# The -dc flag is needed when using BFD insmod on an alpha !
# You should probably also remove -m486 when compiling on the alpha.
#
# FIXME: Is this needed any more?????
#
LD_OPT += -dc
#
# Don't use floating point registers
#
KERNEL_OPT += -mno-fp-regs
###############################################################################
#
# Now follow the options for the v2.0 kernel
#
###############################################################################
ifeq (2.0.,$(findstring 2.0.,$(KERNEL_VERSION)))
# Determine if we can use the BWX instructions with GAS.
old_gas := $(shell if $(AS) --version 2>&1 | grep 'version 2.7' > /dev/null; then echo y; else echo n; fi)
ifneq ($(old_gas),yes)
KERNEL_OPT += -Wa,-m21164a -DBWX_USABLE
# if PYXIS, then enable use of BWIO space
ifeq ($(CONFIG_ALPHA_PYXIS),y)
KERNEL_OPT += -DBWIO_ENABLED
endif
endif
endif # v2.0
###############################################################################
#
# Now follow the options for the v2.2 kernel
#
###############################################################################
ifeq (2.2.,$(findstring 2.2.,$(KERNEL_VERSION)))
#
# When using post-2.0 kernels, register $8 is reserved to hold the
# pointer to the current task structure.
#
KERNEL_OPT += -ffixed-8
#
# The remainder is copied from a v2.2 kernel, from arch/alpha/Makefile:
#
# Determine if GCC understands the -mcpu= option.
have_mcpu := $(shell if $(CC) -mcpu=ev5 -S -o /dev/null -xc /dev/null > /dev/null 2>&1; then echo y; else echo n; fi)
have_mcpu_pca56 := $(shell if $(CC) -mcpu=pca56 -S -o /dev/null -xc /dev/null > /dev/null 2>&1; then echo y; else echo n; fi)
have_mcpu_ev6 := $(shell if $(CC) -mcpu=ev6 -S -o /dev/null -xc /dev/null > /dev/null 2>&1; then echo y; else echo n; fi)
# Turn on the proper cpu optimizations.
ifeq ($(have_mcpu),y)
# If GENERIC, make sure to turn off any instruction set extensions that
# the host compiler might have on by default. Given that EV4 and EV5
# have the same instruction set, prefer EV5 because an EV5 schedule is
# more likely to keep an EV4 processor busy than vice-versa.
ifeq ($(CONFIG_ALPHA_GENERIC),y)
KERNEL_OPT += -mcpu=ev5
endif
ifeq ($(CONFIG_ALPHA_EV4),y)
KERNEL_OPT += -mcpu=ev4
endif
ifeq ($(CONFIG_ALPHA_PYXIS),y)
KERNEL_OPT += -mcpu=ev56
endif
ifeq ($(CONFIG_ALPHA_POLARIS),y)
ifeq ($(have_mcpu_pca56),y)
KERNEL_OPT += -mcpu=pca56
else
KERNEL_OPT += -mcpu=ev56
endif
endif
ifeq ($(CONFIG_ALPHA_EV6),y)
ifeq ($(have_mcpu_ev6),y)
KERNEL_OPT += -mcpu=ev6
else
ifeq ($(have_mcpu_pca56),y)
KERNEL_OPT += -mcpu=pca56
else
KERNEL_OPT += -mcpu=ev56
endif
endif
endif
endif
# For TSUNAMI, we must have the assembler not emulate our instructions.
# The same is true for POLARIS.
# BWX is most important, but we don't really want any emulation ever.
ifeq ($(old_gas),y)
ifneq ($(CONFIG_ALPHA_GENERIC)$(CONFIG_ALPHA_TSUNAMI)$(CONFIG_ALPHA_POLARIS),)
# How do we do #error in make?
ERROR_RULE:
@echo
@echo "*************************************************"
@echo
@echo "Error: Please upgrade your assembler"
@echo
@echo "*************************************************"
@echo
exit 1
endif
else
ifeq ($(CONFIG_ALPHA_GENERIC),y)
KERNEL_OPT += -Wa,-mev6
endif
ifeq ($(CONFIG_ALPHA_PYXIS),y)
KERNEL_OPT += -Wa,-m21164a -DBWIO_ENABLED
endif
ifeq ($(CONFIG_ALPHA_POLARIS),y)
KERNEL_OPT += -Wa,-m21164pc
endif
ifeq ($(CONFIG_ALPHA_TSUNAMI),y)
KERNEL_OPT += -Wa,-mev6
endif
endif
endif
else # alpha
ERROR_RULE:
@echo
@echo "*************************************************"
@echo
@echo "Unluckily no other archives besides x86 and alpha"
@echo "are supported at this time. Sorry."
@echo
@echo "*************************************************"
@echo
exit 1
endif # !alpha
endif # !i386
#
# these are the flags referred to by the make rules in Rules.make.
#
GKSFLAGS = $(KERNEL_OPT) $(EXTRA_CFLAGS)
CPPFLAGS = $(KERNEL_OPT) $(MODULE_OPT) $(EXTRA_CFLAGS)
CFLAGS = $(WARNINGS) $(COMPILE) $(CPPFLAGS)
SFLAGS = -fverbose-asm $(CFLAGS)
EXTRA_LDFLAGS = $(LD_OPT)
INSTALL = install -c -o root -g root
#
# end of MCONFIG
#
################################################################################
# LocalWords: cvs ftape MCONFIG QIC Linux usr src linux Ok UTS ifeq config FS
# LocalWords: wildcard MODVERSIONS modversions PROC MAMDK endif MODULESDIR lib
# LocalWords: misc swapout kdtime SBINDIR sbin INFODIR DOCDIR html dvi doc SMP
# LocalWords: MANDIR FDC FC IRQ DMA fd fdc dma CLK Mhz DCONFIG CMS Mbps CTC Mb
# LocalWords: ExaByte GCC gcc NR Sparc Mips proc kb dif DTHE claus momo rwth
# LocalWords: aachen DBROKEN DMODULE DMODVERSIONS TOPDIR GENKSYMS genksyms ZFT
# LocalWords: ZFTAPE ifneq findstring ifdef DCPU mamdk frisc Wstrict fomit fno
# LocalWords: LD dc BFD insmod CC GKSFLAGS CFLAGS CPPFLAGS SFLAGS fverbose asm
# LocalWords: LDFLAGS ftformat procfs LocalWords
