I have a HP 6200c USB scanner. It works reasonably well with 2.4.9, but with 2.4.10 , 2.4.13 and 2.4.14 it refuses to work. I'm using a VIA motherboard.
>From 2.4.9 : cat /proc/bus/usb/devices T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 11/900 us ( 1%), #Int= 1, #Iso= 0 D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 0.00 S: Product=USB UHCI Root Hub S: SerialNumber=6800 C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=045e ProdID=0038 Rev= 1.05 S: Manufacturer=Microsoft S: Product=SideWinder Precision 2 Joystick C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 20mA I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=(none) E: Ad=81(I) Atr=03(Int.) MxPS= 6 Ivl= 10ms T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=03f0 ProdID=0201 Rev= 1.00 S: SerialNumber=SG8BO110JYHL C:* #Ifs= 1 Cfg#= 1 Atr=60 MxPwr= 0mA ********* at this point there is a brief hange ******** I: If#= 0 Alt= 0 #EPs= 3 Cls=00(>ifc ) Sub=00 Prot=00 Driver=usbscanner E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 16 Ivl= 0ms E: Ad=83(I) Atr=03(Int.) MxPS= 1 Ivl=250ms Note that it doesn't list the vendor string for the scanner ? Under 2.4.10+ , the output is much the same. If i run 'scanimage out.pnm' with 2.4.9, the response is quite quick. With 2.4.10+, there is some life from the scanner, but i never get an image. Using xscanimage and GIMP, with 2.4.9 is works most of the time, but is very flakey. If i push it too hard, it tends to fall over. If i'm gentle with it (long time between successive commands), it isn't too bad. Using xscanimage and GIMP, with 2.4.10+ fails 99% of the time. I did once get an image, but only ever once. -- ----------------------- [EMAIL PROTECTED] ----------------------- _______________________________________________ [EMAIL PROTECTED] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
