* David Brownell <[EMAIL PROTECTED]>:
> > Drive is connected to "PCI device 10de:0068 (nVidia Corporation)"
>
> Doesn't look like it. There was no storage device in what you sent.
OK, today I'm much more awake...
So here's plain -rc2:
interrupts:
3: 4 XT-PIC ehci_hcd
10: 93 XT-PIC usb-ohci
11: 13 XT-PIC usb-ohci, eth0
lspci:
00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller (rev
a3) (prog-if 10 [OHCI])
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device
f541
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at ee086000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller (rev
a3) (prog-if 10 [OHCI])
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device
f541
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 11
Region 0: Memory at ee082000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller (rev
a3) (prog-if 20 [EHCI])
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device
f541
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 3
Region 0: Memory at ee085000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] #0a [2080]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
dmesg (plug-in, mount, dump):
Aug 11 07:49:05 artus kernel: ehci_hcd 00:02.2: GetStatus port 1 status
003802 POWER OWNER sig=j CSC
Aug 11 07:49:05 artus kernel: hub.c: port 1, portstatus 0, change 1, 12
Mb/s
Aug 11 07:49:05 artus kernel: hub.c: port 1 connection change
Aug 11 07:49:05 artus kernel: hub.c: port 1, portstatus 0, change 1, 12
Mb/s
Aug 11 07:49:05 artus kernel: ehci_hcd 00:02.2: GetStatus port 2 status
001803 POWER sig=j CSC CONNECT
Aug 11 07:49:05 artus kernel: hub.c: port 2, portstatus 501, change 1,
480 Mb/s
Aug 11 07:49:05 artus kernel: hub.c: port 2 connection change
Aug 11 07:49:05 artus kernel: hub.c: port 2, portstatus 501, change 1,
480 Mb/s
Aug 11 07:49:05 artus kernel: hub.c: port 2, portstatus 501, change 0,
480 Mb/s
Aug 11 07:49:05 artus last message repeated 3 times
Aug 11 07:49:05 artus kernel: hub.c: port 2, portstatus 511, change 0,
480 Mb/s
Aug 11 07:49:05 artus kernel: hub.c: port 2 of hub 1 not reset yet,
waiting 10ms
Aug 11 07:49:05 artus kernel: hub.c: port 2, portstatus 511, change 0,
480 Mb/s
Aug 11 07:49:05 artus kernel: hub.c: port 2 of hub 1 not reset yet,
waiting 10ms
Aug 11 07:49:05 artus kernel: ehci_hcd 00:02.2: port 2 high speed
Aug 11 07:49:05 artus kernel: ehci_hcd 00:02.2: GetStatus port 2 status
001005 POWER sig=se0 PE CONNECT
Aug 11 07:49:05 artus kernel: hub.c: port 2, portstatus 503, change 10,
480 Mb/s
Aug 11 07:49:05 artus kernel: hub.c: new USB device 00:02.2-2, assigned
address 4
Aug 11 07:49:05 artus kernel: usb.c: kmalloc IF deeb3400, numif 1
Aug 11 07:49:05 artus kernel: usb.c: new device strings: Mfr=0,
Product=1, SerialNumber=0
Aug 11 07:49:05 artus kernel: usb.c: USB device number 4 default
language ID 0x409
Aug 11 07:49:05 artus kernel: Product: USB TO IDE
Aug 11 07:49:05 artus kernel: scsi1 : SCSI emulation for USB Mass
Storage devices
Aug 11 07:49:05 artus kernel: Vendor: Maxtor 6 Model: Y120L0
Rev: 0811
Aug 11 07:49:05 artus kernel: Type: Direct-Access
ANSI SCSI revision: 02
Aug 11 07:49:05 artus kernel: Attached scsi disk sda at scsi1, channel
0, id 0, lun 0
Aug 11 07:49:05 artus kernel: SCSI device sda: 240121728 512-byte hdwr
sectors (122942 MB)
Aug 11 07:49:05 artus kernel: /dev/scsi/host1/bus0/target0/lun0: p1
Aug 11 07:49:05 artus kernel: WARNING: USB Mass Storage data integrity
not assured
Aug 11 07:49:05 artus kernel: USB Mass Storage device found at 4
Aug 11 07:49:05 artus kernel: usb.c: usb-storage driver claimed
interface deeb3400
Aug 11 07:49:05 artus kernel: hub.c: port 3, portstatus 100, change 0,
12 Mb/s
Aug 11 07:49:05 artus kernel: hub.c: port 4, portstatus 100, change 0,
12 Mb/s
Aug 11 07:49:05 artus kernel: hub.c: port 5, portstatus 100, change 0,
12 Mb/s
Aug 11 07:49:05 artus kernel: hub.c: port 6, portstatus 100, change 0,
12 Mb/s
Aug 11 07:49:18 artus kernel: kjournald starting. Commit interval 5
seconds
Aug 11 07:49:18 artus kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on
sd(8,1), internal journal
Aug 11 07:49:18 artus kernel: EXT3-fs: mounted filesystem with ordered
data mode.
Aug 11 07:51:46 artus kernel: ehci_hcd 00:02.2: cancel qh dfe13100
n1fe13002 info 42002204 40000000 qtd 1fe120c0
Aug 11 07:51:46 artus kernel: ehci_hcd 00:02.2: overlay td dfe13110
n1fe12060 00000003 t8a008c81 p0=176e3600
Aug 11 07:51:46 artus kernel: ehci_hcd 00:02.2: cancel td dfe120c0
n1fe12060 00000001 t10008c80 p0=176e3000
Aug 11 07:51:51 artus kernel: usb_control/bulk_msg: timeout
Aug 11 07:51:51 artus kernel: ehci_hcd 00:02.2: cancel qh dfe13080
n1fe13002 info 40406004 40000000 qtd 1fe121e0
Aug 11 07:51:51 artus kernel: ehci_hcd 00:02.2: overlay td dfe13090
n1fe120c0 0000001f t80008d80 p0=00000000
Aug 11 07:51:51 artus kernel: ehci_hcd 00:02.2: cancel td dfe121e0
n1fe120c0 00000001 t80008d80 p0=00000000
Aug 11 07:52:01 artus kernel: ehci_hcd 00:02.2: cancel qh dfe13100
n1fe13002 info 42002204 40000000 qtd 1fe12060
Aug 11 07:52:01 artus kernel: ehci_hcd 00:02.2: overlay td dfe13110
n1fe12120 00000005 t801f8c81 p0=1eeb3740
Aug 11 07:52:01 artus kernel: ehci_hcd 00:02.2: cancel td dfe12060
n1fe12120 00000001 t001f8c80 p0=1eeb3740
Aug 11 07:52:06 artus kernel: usb_control/bulk_msg: timeout
Aug 11 07:52:06 artus kernel: ehci_hcd 00:02.2: cancel qh dfe13080
n1fe13002 info 40406004 40000000 qtd 1fe121e0
Aug 11 07:52:06 artus kernel: ehci_hcd 00:02.2: overlay td dfe13090
n1fe12060 00000001 t80008d80 p0=00000000
Aug 11 07:52:06 artus kernel: ehci_hcd 00:02.2: cancel td dfe121e0
n1fe12060 00000001 t80008d80 p0=00000000
Aug 11 07:52:11 artus kernel: usb_control/bulk_msg: timeout
Aug 11 07:52:11 artus kernel: ehci_hcd 00:02.2: cancel qh dfe13080
n1fe13002 info 40406004 40000000 qtd 1fe121e0
Aug 11 07:52:11 artus kernel: ehci_hcd 00:02.2: overlay td dfe13090
n1fe120c0 00000005 t80008d80 p0=00000000
Aug 11 07:52:11 artus kernel: ehci_hcd 00:02.2: cancel td dfe121e0
n1fe120c0 00000001 t80008d80 p0=00000000
Aug 11 07:52:11 artus kernel: hub.c: port 2, portstatus 511, change 0,
480 Mb/s
Aug 11 07:52:11 artus kernel: hub.c: port 2 of hub 1 not reset yet,
waiting 10ms
Aug 11 07:52:11 artus kernel: hub.c: port 2, portstatus 511, change 0,
480 Mb/s
Aug 11 07:52:11 artus kernel: hub.c: port 2 of hub 1 not reset yet,
waiting 10ms
Aug 11 07:52:11 artus kernel: ehci_hcd 00:02.2: port 2 full speed -->
companion
Aug 11 07:52:11 artus kernel: ehci_hcd 00:02.2: GetStatus port 2 status
003001 POWER OWNER sig=se0 CONNECT
Aug 11 07:52:11 artus kernel: hub.c: port 2, portstatus 0, change 10, 12
Mb/s
Aug 11 07:52:11 artus kernel: ehci_hcd 00:02.2: GetStatus port 1 status
003802 POWER OWNER sig=j CSC
Aug 11 07:52:11 artus kernel: hub.c: port 1, portstatus 0, change 1, 12
Mb/s
Aug 11 07:52:11 artus kernel: hub.c: port 1 connection change
Aug 11 07:52:11 artus kernel: hub.c: port 1, portstatus 0, change 1, 12
Mb/s
Aug 11 07:52:11 artus kernel: ehci_hcd 00:02.2: GetStatus port 2 status
001002 POWER sig=se0 CSC
Aug 11 07:52:11 artus kernel: hub.c: port 2, portstatus 100, change 1,
12 Mb/s
Aug 11 07:52:11 artus kernel: hub.c: port 2 connection change
Aug 11 07:52:11 artus kernel: hub.c: port 2, portstatus 100, change 1,
12 Mb/s
Aug 11 07:52:11 artus kernel: usb.c: USB disconnect on device 00:02.2-2
address 4
Aug 11 07:52:11 artus kernel: ehci_hcd 00:02.2: free_config 2 devnum 4
Aug 11 07:52:11 artus kernel: hub.c: port 3, portstatus 100, change 0,
12 Mb/s
Aug 11 07:52:11 artus kernel: hub.c: port 4, portstatus 100, change 0,
12 Mb/s
Aug 11 07:52:11 artus kernel: hub.c: port 5, portstatus 100, change 0,
12 Mb/s
Aug 11 07:52:11 artus kernel: hub.c: port 6, portstatus 100, change 0,
12 Mb/s
Aug 11 07:52:16 artus kernel: usb-storage: host_reset() requested but
not implemented
Aug 11 07:52:26 artus kernel: scsi: device set offline - command error
recover failed: host 1 channel 0 id 0 lun 0
Aug 11 07:52:26 artus kernel: 248
Aug 11 07:52:26 artus kernel: I/O error: dev 08:01, sector 88989496
Aug 11 07:52:26 artus kernel: I/O error: dev 08:01, sector 88989744
> > 00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller
> > (rev a3) (prog-if 20 [EHCI]) Subsystem: Holco Enterprise Co,
> > Ltd/Shuttle Computer: Unknown device f541
>
> An SN41G2? :)
Yep. Nice little box.
> >> - Results of using the same drivers on 2.6.0-test3, which has
> >> much better code in the layers over the ehci driver.
> >
> > Would love to, but 2.6.0 doesn't work too well for me.
>
> Curious. You should report the problems to LKML. Works fine for me,
> on hardware that seems to be almost identical to yours.
The main problem is the binary ethernet-driver from nvidia for the
nForce2. And that's not a kernel-problem... But I already have a
realtek for my PCI, so this problem will go away.
And during testing -test3 on my notebook, it ate my ext3-fs, so this
thing is not going onto my desktop system (although I've got backups)
Report is on the way.
> > If you need anything else, just let me know. :)
>
> Seems like this diagnostic patch should turn up anything that's to
> be turned up, if it's a real issue in the EHCI code.
See above.
--
Fridtjof Busse
panic("Tell me what a watchpoint trap is, and I'll then
deal with such a beast...");
2.2.16 /usr/src/linux/arch/arch/sparc/kernel/traps.c
-------------------------------------------------------
This SF.Net email sponsored by: Free pre-built ASP.NET sites including
Data Reports, E-commerce, Portals, and Forums are available now.
Download today and enter to win an XBOX or Visual Studio .NET.
http://aspnet.click-url.com/go/psa00100003ave/direct;at.aspnet_072303_01/01
_______________________________________________
[EMAIL PROTECTED]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
