Hi All,
I am able to fix the problem by using the following patch:
--- linux-2.6.0-test6/drivers/usb/host/uhci-hcd.c 2003-09-28 02:50:56.000000000
+0200
+++ linux-2.6.0-test6/drivers/usb/host/uhci-hcd.c 2003-09-28 23:21:30.000000000
+0200
@@ -2185,8 +2185,8 @@
/* Maybe kick BIOS off this hardware. Then reset, so we won't get
* interrupts from any previous setup.
*/
- pci_write_config_word(hcd->pdev, USBLEGSUP, USBLEGSUP_DEFAULT);
reset_hc(uhci);
+ pci_write_config_word(hcd->pdev, USBLEGSUP, USBLEGSUP_DEFAULT);
return 0;
}
Greetings,
Wim.
> Hi All,
>
> Since linux 2.6.0-test5 I seem to have a problem with the IRQ handling of the
> uhci-hcd module.
> Since the IRQ that get's disabled is the same IRQ as my adaptec SCSI controller, my
> system crashes rather hard.
>
> I included the log file of what happens.
>
> Greetings,
> Wim.
>
> [EMAIL PROTECTED] root]# dmesg
> Linux version 2.6.0-test5 ([EMAIL PROTECTED]) (gcc version 3.2.2 20030222 (Red Hat
> Linux 3.2.2-5)) #4 Tue Sep 16 22:20:03 CEST 2003
> Video mode to be used for restore is f00
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 0000000007ff0000 (usable)
> BIOS-e820: 0000000007ff0000 - 0000000007ff3000 (ACPI NVS)
> BIOS-e820: 0000000007ff3000 - 0000000008000000 (ACPI data)
> BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
> 127MB LOWMEM available.
> On node 0 totalpages: 32752
> DMA zone: 4096 pages, LIFO batch:1
> Normal zone: 28656 pages, LIFO batch:6
> HighMem zone: 0 pages, LIFO batch:1
> DMI 2.1 present.
> Building zonelist for node : 0
> Kernel command line: ro noinitrd root=/dev/sda1
> Initializing CPU#0
> PID hash table entries: 512 (order 9: 4096 bytes)
> Detected 299.208 MHz processor.
> Console: colour VGA+ 80x25
> Memory: 126472k/131008k available (1513k kernel code, 3984k reserved, 521k data,
> 304k init, 0k highmem)
> Calibrating delay loop... 589.82 BogoMIPS
> Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
> Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
> Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
> -> /dev
> -> /dev/console
> -> /root
> CPU: After generic identify, caps: 0080f9ff 00000000 00000000 00000000
> CPU: After vendor identify, caps: 0080f9ff 00000000 00000000 00000000
> CPU: L1 I cache: 16K, L1 D cache: 16K
> CPU: L2 cache: 512K
> CPU: After all inits, caps: 0080f9ff 00000000 00000000 00000040
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> CPU: Intel Pentium II (Klamath) stepping 04
> Checking 'hlt' instruction... OK.
> POSIX conformance testing by UNIFIX
> NET: Registered protocol family 16
> PCI: PCI BIOS revision 2.10 entry at 0xfb1d0, last bus=1
> PCI: Using configuration type 1
> mtrr: v2.0 (20020519)
> SCSI subsystem initialized
> PCI: Probing PCI hardware
> PCI: Probing PCI hardware (bus 00)
> PCI: Using IRQ router PIIX [8086/7110] at 0000:00:07.0
> pty: 2048 Unix98 ptys configured
> ikconfig 0.6 with /proc/ikconfig
> VFS: Disk quotas dquot_6.5.1
> Initializing Cryptographic API
> Limiting direct PCI/PCI transfers.
> request_module: failed /sbin/modprobe -- parport_lowlevel. error = -16
> lp: driver loaded but no devices found
> Real Time Clock Driver v1.12
> Serial: 8250/16550 driver $Revision: 1.90 $ IRQ sharing disabled
> ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
> parport0: PC-style at 0x378 [PCSPP(,...)]
> lp0: using parport0 (polling).
> Using anticipatory scheduling io scheduler
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
> loop: loaded (max 8 devices)
> 8139too Fast Ethernet driver 0.9.26
> PCI: Found IRQ 10 for device 0000:00:09.0
> eth0: RealTek RTL8139 at 0xc880d000, 00:10:a7:04:d6:a1, IRQ 10
> eth0: Identified 8139 chip type 'RTL-8139B'
> PCI: Found IRQ 11 for device 0000:00:0b.0
> PCI: Sharing IRQ 11 with 0000:00:07.2
> scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.35
> <Adaptec 2940 Ultra SCSI adapter>
> aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
>
> (scsi0:A:0): 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
> (scsi0:A:6): 20.000MB/s transfers (20.000MHz, offset 15)
> Vendor: IBM Model: DFHSS2W Rev: 4141
> Type: Direct-Access ANSI SCSI revision: 02
> scsi0:A:0:0: Tagged Queuing enabled. Depth 253
> Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.02
> Type: CD-ROM ANSI SCSI revision: 02
> SCSI device sda: 4404489 512-byte hdwr sectors (2255 MB)
> SCSI device sda: drive cache: write back
> sda: sda1 sda2
> Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
> sr0: scsi-1 drive
> Uniform CD-ROM driver Revision: 3.12
> Attached scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0
> Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
> Attached scsi generic sg1 at scsi0, channel 0, id 6, lun 0, type 5
> mice: PS/2 mouse device common for all mice
> input: PS/2 Generic Mouse on isa0060/serio1
> serio: i8042 AUX port at 0x60,0x64 irq 12
> input: AT Set 2 keyboard on isa0060/serio0
> serio: i8042 KBD port at 0x60,0x64 irq 1
> NET: Registered protocol family 2
> IP: routing cache hash table of 512 buckets, 4Kbytes
> TCP: Hash tables configured (established 8192 bind 16384)
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> EXT3-fs: INFO: recovery required on readonly filesystem.
> EXT3-fs: write access will be enabled during recovery.
> kjournald starting. Commit interval 5 seconds
> EXT3-fs: recovery complete.
> EXT3-fs: mounted filesystem with ordered data mode.
> VFS: Mounted root (ext3 filesystem) readonly.
> Freeing unused kernel memory: 304k freed
> pcwd_pci: PCI-PC Watchdog driver, v1.00 (07/09/2003)
> pcwd_pci: Found card at port 0xe400 (Firmware: 1.50) with temp option.
> pcwd_pci: No previous trip detected - Cold boot or reset
> pcwd_pci: initialized. timeout=2 sec (nowayout=0)
> EXT3 FS on sda1, internal journal
> Adding 265064k swap on /dev/sda2. Priority:-1 extents:1
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> ip_tables: (C) 2000-2002 Netfilter core team
> ip_tables: (C) 2000-2002 Netfilter core team
> eth0: link up, 10Mbps, half-duplex, lpa 0x0000
> ip_tables: (C) 2000-2002 Netfilter core team
> [EMAIL PROTECTED] root]# lsmod
> Module Size Used by
> iptable_filter 2656 0
> ip_tables 16880 1 iptable_filter
> pcwd_pci 8612 0
> [EMAIL PROTECTED] root]# modinfo usbcore
> license: GPL
> vermagic: 2.6.0-test5 PENTIUMII gcc-3.2
> depends:
> alias: usb:v*p*dl*dh*dc09dsc*dp*ic*isc*ip*
> alias: usb:v*p*dl*dh*dc*dsc*dp*ic09isc*ip*
> [EMAIL PROTECTED] root]# modprobe usbcore
> [EMAIL PROTECTED] root]# dmesg | tail
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> ip_tables: (C) 2000-2002 Netfilter core team
> ip_tables: (C) 2000-2002 Netfilter core team
> eth0: link up, 10Mbps, half-duplex, lpa 0x0000
> ip_tables: (C) 2000-2002 Netfilter core team
> drivers/usb/core/usb.c: registered new driver usbfs
> drivers/usb/core/usb.c: registered new driver hub
> [EMAIL PROTECTED] root]# lsmod
> Module Size Used by
> usbcore 105492 0
> iptable_filter 2656 0
> ip_tables 16880 1 iptable_filter
> pcwd_pci 8612 0
> [EMAIL PROTECTED] root]# modinfo uhci-hcd
> parm: debug:Debug level
> author: Linus 'Frodo Rabbit' Torvalds, Johannes Erdfelt, Randy Dunlap, Georg
> Acher, Deti Fliegl, Thomas Sailer, Roman Weissgaerber
> description: USB Universal Host Controller Interface driver
> license: GPL
> vermagic: 2.6.0-test5 PENTIUMII gcc-3.2
> depends: usbcore
> alias: pci:v*d*sv*sd*bc0Csc03i00*
> [EMAIL PROTECTED] root]# lspci
> 00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 02)
> 00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 02)
> 00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
> 00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
> 00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
> 00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
> 00:08.0 DPIO module: Quicklogic Corporation PC Watchdog (rev 01)
> 00:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+
> (rev 10)
> 00:0a.0 VGA compatible controller: Matrox Graphics, Inc. MGA 2064W [Millennium] (rev
> 01)
> 00:0b.0 SCSI storage controller: Adaptec AHA-2940U/UW/D / AIC-7881U
> [EMAIL PROTECTED] root]# modprobe uhci-hcd
> [EMAIL PROTECTED] root]# dmesg
> Linux version 2.6.0-test5 ([EMAIL PROTECTED]) (gcc version 3.2.2 20030222 (Red Hat
> Linux 3.2.2-5)) #4 Tue Sep 16 22:20:03 CEST 2003
> Video mode to be used for restore is f00
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 0000000007ff0000 (usable)
> BIOS-e820: 0000000007ff0000 - 0000000007ff3000 (ACPI NVS)
> BIOS-e820: 0000000007ff3000 - 0000000008000000 (ACPI data)
> BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
> 127MB LOWMEM available.
> On node 0 totalpages: 32752
> DMA zone: 4096 pages, LIFO batch:1
> Normal zone: 28656 pages, LIFO batch:6
> HighMem zone: 0 pages, LIFO batch:1
> DMI 2.1 present.
> Building zonelist for node : 0
> Kernel command line: ro noinitrd root=/dev/sda1
> Initializing CPU#0
> PID hash table entries: 512 (order 9: 4096 bytes)
> Detected 299.208 MHz processor.
> Console: colour VGA+ 80x25
> Memory: 126472k/131008k available (1513k kernel code, 3984k reserved, 521k data,
> 304k init, 0k highmem)
> Calibrating delay loop... 589.82 BogoMIPS
> Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
> Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
> Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
> -> /dev
> -> /dev/console
> -> /root
> CPU: After generic identify, caps: 0080f9ff 00000000 00000000 00000000
> CPU: After vendor identify, caps: 0080f9ff 00000000 00000000 00000000
> CPU: L1 I cache: 16K, L1 D cache: 16K
> CPU: L2 cache: 512K
> CPU: After all inits, caps: 0080f9ff 00000000 00000000 00000040
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> CPU: Intel Pentium II (Klamath) stepping 04
> Checking 'hlt' instruction... OK.
> POSIX conformance testing by UNIFIX
> NET: Registered protocol family 16
> PCI: PCI BIOS revision 2.10 entry at 0xfb1d0, last bus=1
> PCI: Using configuration type 1
> mtrr: v2.0 (20020519)
> SCSI subsystem initialized
> PCI: Probing PCI hardware
> PCI: Probing PCI hardware (bus 00)
> PCI: Using IRQ router PIIX [8086/7110] at 0000:00:07.0
> pty: 2048 Unix98 ptys configured
> ikconfig 0.6 with /proc/ikconfig
> VFS: Disk quotas dquot_6.5.1
> Initializing Cryptographic API
> Limiting direct PCI/PCI transfers.
> request_module: failed /sbin/modprobe -- parport_lowlevel. error = -16
> lp: driver loaded but no devices found
> Real Time Clock Driver v1.12
> Serial: 8250/16550 driver $Revision: 1.90 $ IRQ sharing disabled
> ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
> parport0: PC-style at 0x378 [PCSPP(,...)]
> lp0: using parport0 (polling).
> Using anticipatory scheduling io scheduler
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
> loop: loaded (max 8 devices)
> 8139too Fast Ethernet driver 0.9.26
> PCI: Found IRQ 10 for device 0000:00:09.0
> eth0: RealTek RTL8139 at 0xc880d000, 00:10:a7:04:d6:a1, IRQ 10
> eth0: Identified 8139 chip type 'RTL-8139B'
> PCI: Found IRQ 11 for device 0000:00:0b.0
> PCI: Sharing IRQ 11 with 0000:00:07.2
> scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.35
> <Adaptec 2940 Ultra SCSI adapter>
> aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
>
> (scsi0:A:0): 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
> (scsi0:A:6): 20.000MB/s transfers (20.000MHz, offset 15)
> Vendor: IBM Model: DFHSS2W Rev: 4141
> Type: Direct-Access ANSI SCSI revision: 02
> scsi0:A:0:0: Tagged Queuing enabled. Depth 253
> Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.02
> Type: CD-ROM ANSI SCSI revision: 02
> SCSI device sda: 4404489 512-byte hdwr sectors (2255 MB)
> SCSI device sda: drive cache: write back
> sda: sda1 sda2
> Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
> sr0: scsi-1 drive
> Uniform CD-ROM driver Revision: 3.12
> Attached scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0
> Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
> Attached scsi generic sg1 at scsi0, channel 0, id 6, lun 0, type 5
> mice: PS/2 mouse device common for all mice
> input: PS/2 Generic Mouse on isa0060/serio1
> serio: i8042 AUX port at 0x60,0x64 irq 12
> input: AT Set 2 keyboard on isa0060/serio0
> serio: i8042 KBD port at 0x60,0x64 irq 1
> NET: Registered protocol family 2
> IP: routing cache hash table of 512 buckets, 4Kbytes
> TCP: Hash tables configured (established 8192 bind 16384)
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> EXT3-fs: INFO: recovery required on readonly filesystem.
> EXT3-fs: write access will be enabled during recovery.
> kjournald starting. Commit interval 5 seconds
> EXT3-fs: recovery complete.
> EXT3-fs: mounted filesystem with ordered data mode.
> VFS: Mounted root (ext3 filesystem) readonly.
> Freeing unused kernel memory: 304k freed
> pcwd_pci: PCI-PC Watchdog driver, v1.00 (07/09/2003)
> pcwd_pci: Found card at port 0xe400 (Firmware: 1.50) with temp option.
> pcwd_pci: No previous trip detected - Cold boot or reset
> pcwd_pci: initialized. timeout=2 sec (nowayout=0)
> EXT3 FS on sda1, internal journal
> Adding 265064k swap on /dev/sda2. Priority:-1 extents:1
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> ip_tables: (C) 2000-2002 Netfilter core team
> ip_tables: (C) 2000-2002 Netfilter core team
> eth0: link up, 10Mbps, half-duplex, lpa 0x0000
> ip_tables: (C) 2000-2002 Netfilter core team
> drivers/usb/core/usb.c: registered new driver usbfs
> drivers/usb/core/usb.c: registered new driver hub
> drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1
> PCI: Found IRQ 11 for device 0000:00:07.2
> PCI: Sharing IRQ 11 with 0000:00:0b.0
> uhci-hcd 0000:00:07.2: UHCI Host Controller
> irq 11: nobody cared!
> Call Trace:
> [<c010c96b>] __report_bad_irq+0x2b/0x90
> [<c010ca56>] note_interrupt+0x66/0xa0
> [<c010cc60>] do_IRQ+0xf0/0x100
> [<c010b18c>] common_interrupt+0x18/0x20
> [<c011dd7d>] do_softirq+0x4d/0xc0
> [<c010cc47>] do_IRQ+0xd7/0x100
> [<c010b18c>] common_interrupt+0x18/0x20
> [<c01a81c8>] pci_bus_write_config_word+0x58/0x60
> [<c885d0e0>] uhci_reset+0x40/0x60 [uhci_hcd]
> [<c8876325>] usb_hcd_pci_probe+0x205/0x480 [usbcore]
> [<c017bead>] sysfs_new_inode+0x5d/0xa0
> [<c017bf54>] sysfs_create+0x64/0x90
> [<c01aa38d>] pci_device_probe_static+0x4d/0x60
> [<c01aa4cc>] __pci_device_probe+0x3c/0x50
> [<c01aa50c>] pci_device_probe+0x2c/0x50
> [<c01cea6d>] bus_match+0x3d/0x70
> [<c01cebd0>] driver_attach+0x70/0xb0
> [<c01cee90>] bus_add_driver+0x90/0xb0
> [<c01cf2c1>] driver_register+0x31/0x40
> [<c01aa75f>] pci_register_driver+0x5f/0x90
> [<c88420db>] uhci_hcd_init+0xdb/0x13d [uhci_hcd]
> [<c012f022>] sys_init_module+0x102/0x1d0
> [<c010afcd>] sysenter_past_esp+0x52/0x71
>
> handlers:
> [<c020b9a0>] (ahc_linux_isr+0x0/0x280)
> Disabling IRQ #11
> uhci-hcd 0000:00:07.2: irq 11, io base 0000e000
> uhci-hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
> drivers/usb/host/uhci-hcd.c: detected 2 ports
> hub 1-0:0: USB hub found
> hub 1-0:0: 2 ports detected
> [EMAIL PROTECTED] root]# dmesg | tail
>
> Message from [EMAIL PROTECTED] at Wed Sep 17 21:28:32 2003 ...
> stafke kernel: Disabling IRQ #11
>
> Message from [EMAIL PROTECTED] at Wed Sep 17 21:28:32 2003 ...
> stafke kernel: journal commit I/O error
> scsi0:0:0:0: Command already completed
> aic7xxx_abort returns 0x2002
> scsi0:0:0:0: Attempting to queue a TARGET RESET message
> CDB: 0x2a 0x0 0x0 0x2 0x87 0x3f 0x0 0x0 0x8 0x0
> scsi0:0:0:0: Command not found
> aic7xxx_dev_reset returns 0x2002
> scsi0:0:0:0: Attempting to queue an ABORT message
> CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> scsi0:0:0:0: Command already completed
> aic7xxx_abort returns 0x2002
> [EMAIL PROTECTED] root]# dmesg
> id 0, lun 0
> sr0: scsi-1 drive
> Uniform CD-ROM driver Revision: 3.12
> Attached scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0
> Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
> Attached scsi generic sg1 at scsi0, channel 0, id 6, lun 0, type 5
> mice: PS/2 mouse device common for all mice
> input: PS/2 Generic Mouse on isa0060/serio1
> serio: i8042 AUX port at 0x60,0x64 irq 12
> input: AT Set 2 keyboard on isa0060/serio0
> serio: i8042 KBD port at 0x60,0x64 irq 1
> NET: Registered protocol family 2
> IP: routing cache hash table of 512 buckets, 4Kbytes
> TCP: Hash tables configured (established 8192 bind 16384)
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> EXT3-fs: INFO: recovery required on readonly filesystem.
> EXT3-fs: write access will be enabled during recovery.
> kjournald starting. Commit interval 5 seconds
> EXT3-fs: recovery complete.
> EXT3-fs: mounted filesystem with ordered data mode.
> VFS: Mounted root (ext3 filesystem) readonly.
> Freeing unused kernel memory: 304k freed
> pcwd_pci: PCI-PC Watchdog driver, v1.00 (07/09/2003)
> pcwd_pci: Found card at port 0xe400 (Firmware: 1.50) with temp option.
> pcwd_pci: No previous trip detected - Cold boot or reset
> pcwd_pci: initialized. timeout=2 sec (nowayout=0)
> EXT3 FS on sda1, internal journal
> Adding 265064k swap on /dev/sda2. Priority:-1 extents:1
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> (scsi0:A:0:0): CDB: 0x12 0x1 0x80 0x0 0x60 0x0
> (scsi0:A:0:0): Saw underflow (76 of 96 bytes). Treated as error
> ip_tables: (C) 2000-2002 Netfilter core team
> ip_tables: (C) 2000-2002 Netfilter core team
> eth0: link up, 10Mbps, half-duplex, lpa 0x0000
> ip_tables: (C) 2000-2002 Netfilter core team
> drivers/usb/core/usb.c: registered new driver usbfs
> drivers/usb/core/usb.c: registered new driver hub
> drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1
> PCI: Found IRQ 11 for device 0000:00:07.2
> PCI: Sharing IRQ 11 with 0000:00:0b.0
> uhci-hcd 0000:00:07.2: UHCI Host Controller
> irq 11: nobody cared!
> Call Trace:
> [<c010c96b>] __report_bad_irq+0x2b/0x90
> [<c010ca56>] note_interrupt+0x66/0xa0
> [<c010cc60>] do_IRQ+0xf0/0x100
> [<c010b18c>] common_interrupt+0x18/0x20
> [<c011dd7d>] do_softirq+0x4d/0xc0
> [<c010cc47>] do_IRQ+0xd7/0x100
> [<c010b18c>] common_interrupt+0x18/0x20
> [<c01a81c8>] pci_bus_write_config_word+0x58/0x60
> [<c885d0e0>] uhci_reset+0x40/0x60 [uhci_hcd]
> [<c8876325>] usb_hcd_pci_probe+0x205/0x480 [usbcore]
> [<c017bead>] sysfs_new_inode+0x5d/0xa0
> [<c017bf54>] sysfs_create+0x64/0x90
> [<c01aa38d>] pci_device_probe_static+0x4d/0x60
> [<c01aa4cc>] __pci_device_probe+0x3c/0x50
> [<c01aa50c>] pci_device_probe+0x2c/0x50
> [<c01cea6d>] bus_match+0x3d/0x70
> [<c01cebd0>] driver_attach+0x70/0xb0
> [<c01cee90>] bus_add_driver+0x90/0xb0
> [<c01cf2c1>] driver_register+0x31/0x40
> [<c01aa75f>] pci_register_driver+0x5f/0x90
> [<c88420db>] uhci_hcd_init+0xdb/0x13d [uhci_hcd]
> [<c012f022>] sys_init_module+0x102/0x1d0
> [<c010afcd>] sysenter_past_esp+0x52/0x71
>
> handlers:
> [<c020b9a0>] (ahc_linux_isr+0x0/0x280)
> Disabling IRQ #11
> uhci-hcd 0000:00:07.2: irq 11, io base 0000e000
> uhci-hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
> drivers/usb/host/uhci-hcd.c: detected 2 ports
> hub 1-0:0: USB hub found
> hub 1-0:0: 2 ports detected
> scsi0:0:0:0: Attempting to queue an ABORT message
> CDB: 0x2a 0x0 0x0 0x2 0x87 0x3f 0x0 0x0 0x8 0x0
> scsi0:0:0:0: Command already completed
> aic7xxx_abort returns 0x2002
> scsi0:0:0:0: Attempting to queue an ABORT message
> CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> scsi0:0:0:0: Command already completed
> aic7xxx_abort returns 0x2002
> scsi0:0:0:0: Attempting to queue a TARGET RESET message
> CDB: 0x2a 0x0 0x0 0x2 0x87 0x3f 0x0 0x0 0x8 0x0
> scsi0:0:0:0: Command not found
> aic7xxx_dev_reset returns 0x2002
> scsi0:0:0:0: Attempting to queue an ABORT message
> CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> scsi0:0:0:0: Command already completed
> aic7xxx_abort returns 0x2002
> scsi0:0:0:0: Attempting to queue an ABORT message
> CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> scsi0: At time of recovery, card was paused
> >>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
> scsi0: Dumping Card State in Message-out phase, at SEQADDR 0x171
> Card was paused
> ACCUM = 0xa0, SINDEX = 0x61, DINDEX = 0xc0, ARG_2 = 0x8
> HCNT = 0x0 SCBPTR = 0x3
> SCSISIGI[0xb6]:(REQI|BSYI|ATNI|MSGI|CDI) ERROR[0x0]
> SCSIBUSL[0xc0] LASTPHASE[0xa0]:(MSGI|CDI) SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI)
> SBLKCTL[0x2]:(SELWIDE) SCSIRATE[0x0] SEQCTL[0x10]:(FASTMODE)
> SEQ_FLAGS[0x40]:(NO_CDB_SENT) SSTAT0[0x7]:(DMADONE|SPIORDY|SDONE)
> SSTAT1[0x3]:(REQINIT|PHASECHG) SSTAT2[0x0] SSTAT3[0x0]
> SIMODE0[0x0] SIMODE1[0xac]:(ENSCSIPERR|ENBUSFREE|ENSCSIRST|ENSELTIMO)
> SXFRCTL0[0x88]:(SPIOEN|DFON) DFCNTRL[0x4]:(DIRECTION)
> DFSTATUS[0x6d]:(FIFOEMP|DFTHRESH|HDONE|FIFOQWDEMP|DFCACHETH)
> STACK: 0xe4 0x0 0x169 0x199
> SCB count = 160
> Kernel NEXTQSCB = 21
> Card NEXTQSCB = 21
> QINFIFO entries:
> Waiting Queue entries:
> Disconnected Queue entries:
> QOUTFIFO entries:
> Sequencer Free SCB List: 6 11 14 10 12 15 0 9 8 4 5 2 1 13 7
> Sequencer SCB Info:
> 0 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 1 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 2 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 3 SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]
> SCB_TAG[0x20]
> 4 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 5 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 6 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 7 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 8 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 9 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 10 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 11 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 12 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 13 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 14 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 15 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> Pending list:
> 32 SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]
> Kernel Free SCB list: 25 4 3 19 26 28 39 13 17 11 27 14 12 36 0 20 24 10 31 18 1 7
> 35 30 8 43 29 156 15 2 33 9 6 16 37 5 34 22 38 23 157 158 159 152 153 154 155 148
> 149 150 151 144 145 146 147 140 141 142 143 136 137 138 139 132 133 134 135 128 129
> 130 131 124 125 126 127 120 121 122 123 116 117 118 119 112 113 114 115 108 109 110
> 111 104 105 106 107 100 101 102 103 96 97 98 99 92 93 94 95 88 89 90 91 84 85 86 87
> 80 81 82 83 76 77 78 79 72 73 74 75 68 69 70 71 64 65 66 67 60 61 62 63 56 57 58 59
> 52 53 54 55 48 49 50 51 44 45 46 47 40 41 42
> DevQ(0:0:0): 0 waiting
> DevQ(0:6:0): 0 waiting
>
> <<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
> scsi0:0:0:0: Device is active, asserting ATN
> Recovery code sleeping
> Recovery code awake
> Timer Expired
> aic7xxx_abort returns 0x2003
> scsi: Device offlined - not ready after error recovery: host 0 channel 0 id 0 lun 0
> SCSI error : <0 0 0 0> return code = 0x6000000
> end_request: I/O error, dev sda, sector 165695
> Buffer I/O error on device sda1, logical block 20704
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 393225
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 393216
> lost page write due to I/O error on sda1
> Buffer I/O error on device sda1, logical block 393217
> lost page write due to I/O error on sda1
> Buffer I/O error on device sda1, logical block 393218
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 393376
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 393377
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 393395
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 393399
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 393723
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 425986
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 425997
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 426043
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 426071
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 458808
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 360479
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 327696
> lost page write due to I/O error on sda1
> Buffer I/O error on device sda1, logical block 327697
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 327695
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 327689
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 229423
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 229420
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 229407
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 229396
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 229395
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 229390
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 229384
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 164035
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 131229
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 131161
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 65801
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 65787
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 32787
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 0
> lost page write due to I/O error on sda1
> Buffer I/O error on device sda1, logical block 1
> lost page write due to I/O error on sda1
> Buffer I/O error on device sda1, logical block 2
> lost page write due to I/O error on sda1
> scsi0 (0:0): rejecting I/O to offline device
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 1731
> lost page write due to I/O error on sda1
> Aborting journal on device sda1.
> ext3_reserve_inode_write: aborting transaction: Journal has aborted in
> __ext3_journal_get_write_access<2>EXT3-fs error (device sda1) in
> ext3_reserve_inode_write: Journal has aborted
> buffer layer error at fs/buffer.c:1260
> Call Trace:
> [<c014bf54>] mark_buffer_dirty+0x54/0x60
> [<c018b69d>] ext3_commit_super+0x4d/0x80
> [<c0188dd1>] ext3_handle_error+0x81/0xc0
> [<c0188f5b>] __ext3_std_error+0x4b/0x60
> [<c0184a59>] ext3_reserve_inode_write+0x59/0xd0
> [<c0184af8>] ext3_mark_inode_dirty+0x28/0x60
> [<c0184bb1>] ext3_dirty_inode+0x81/0x90
> [<c01668b6>] __mark_inode_dirty+0xc6/0xd0
> [<c0161206>] update_atime+0xd6/0xe0
> [<c0156307>] link_path_walk+0x4a7/0x810
> [<c0115fe6>] do_page_fault+0x156/0x4ac
> [<c0156fc7>] open_namei+0x87/0x400
> [<c0148c21>] filp_open+0x41/0x70
> [<c0149035>] sys_open+0x55/0x90
> [<c010b01f>] syscall_call+0x7/0xb
>
> buffer layer error at fs/buffer.c:2664
> Call Trace:
> [<c014e05f>] submit_bh+0x12f/0x180
> [<c014e1b9>] sync_dirty_buffer+0x69/0xd0
> [<c0188dd1>] ext3_handle_error+0x81/0xc0
> [<c0188f5b>] __ext3_std_error+0x4b/0x60
> [<c0184a59>] ext3_reserve_inode_write+0x59/0xd0
> [<c0184af8>] ext3_mark_inode_dirty+0x28/0x60
> [<c0184bb1>] ext3_dirty_inode+0x81/0x90
> [<c01668b6>] __mark_inode_dirty+0xc6/0xd0
> [<c0161206>] update_atime+0xd6/0xe0
> [<c0156307>] link_path_walk+0x4a7/0x810
> [<c0115fe6>] do_page_fault+0x156/0x4ac
> [<c0156fc7>] open_namei+0x87/0x400
> [<c0148c21>] filp_open+0x41/0x70
> [<c0149035>] sys_open+0x55/0x90
> [<c010b01f>] syscall_call+0x7/0xb
>
> scsi0 (0:0): rejecting I/O to offline device
> Buffer I/O error on device sda1, logical block 0
> lost page write due to I/O error on sda1
> journal commit I/O error
> ext3_abort called.
> EXT3-fs abort (device sda1): ext3_journal_start: Detected aborted journal
> Remounting filesystem read-only
> EXT3-fs error (device sda1) in start_transaction: Journal has aborted
> EXT3-fs error (device sda1) in ext3_dirty_inode: Journal has aborted
> [EMAIL PROTECTED] root]# exit
> logout
> -bash: /root/.bash_logout: Input/output error
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf
_______________________________________________
[EMAIL PROTECTED]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
