Greets; I haven't tried 2.6.1 plain, but I've lost my scanner and a few other things on the usb bus with 2.6.1-mm1. They've not been working for several days now. With all modules builtin, dmesg reports:
Linux version 2.6.1-mm1 ([EMAIL PROTECTED]) (gcc version 3.2 20020903 (Red Hat Linux 8.0 3.2-7)) #1 Fri Jan 9 11:46:45 EST 2004 [...] Linux video capture interface: v1.00 bttv: driver version 0.9.12 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). bttv0: Bt878 (rev 17) at 0000:00:09.0, irq: 5, latency: 32, mmio: 0xe3004000 bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb bttv0: using: Hauppauge (bt878) [card=10,autodetected] bttv0: Hauppauge/Voodoo msp34xx: reset line init [5] bttv0: Hauppauge eeprom: model=44811, tuner=Temic 4039FR5 (21), radio=yes bttv0: using tuner=21 bttv0: i2c: checking for MSP34xx @ 0x80... not found bttv0: i2c: checking for TDA9875 @ 0xb0... not found bttv0: i2c: checking for TDA7432 @ 0x8a... not found bttv0: registered device video0 bttv0: registered device vbi0 bttv0: registered device radio0 bttv0: PLL: 28636363 => 35468950 .. ok tvaudio: TV audio decoder + audio/video mux driver tvaudio: known chips: tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c54 (PV951),ta8874z tuner: chip found @ 0xc2 tuner: type set to 21 (Temic NTSC (4039 FR5)) registering 0-0061 [...] uhci_hcd 0000:00:11.2: UHCI Host Controller uhci_hcd 0000:00:11.2: irq 11, io base 0000dc00 uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected uhci_hcd 0000:00:11.3: UHCI Host Controller uhci_hcd 0000:00:11.3: irq 11, io base 0000e000 uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected uhci_hcd 0000:00:11.4: UHCI Host Controller uhci_hcd 0000:00:11.4: irq 11, io base 0000e400 uhci_hcd 0000:00:11.4: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected drivers/usb/core/usb.c: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... drivers/usb/core/usb.c: registered new driver usb-storage USB Mass Storage support registered. drivers/usb/core/usb.c: registered new driver hiddev drivers/usb/core/usb.c: registered new driver hid drivers/usb/input/hid-core.c: v2.0:USB HID core driver drivers/usb/core/usb.c: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0 drivers/usb/serial/usb-serial.c: Had to override the write_room usb serial operation with the generic one. drivers/usb/serial/usb-serial.c: Had to override the chars_in_buffer usb serial operation with the generic one. drivers/usb/serial/usb-serial.c: USB Serial support registered for PL-2303 drivers/usb/core/usb.c: registered new driver pl2303 drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver v0.10 mice: PS/2 mouse device common for all mice input: PC Speaker serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 input: AT Translated Set 2 keyboard on isa0060/serio0 i2c /dev entries driver tuner: type already set (21) registering 0-0050 tuner: type already set (21) registering 0-0051 tuner: type already set (21) registering 0-0052 tuner: type already set (21) registering 0-0053 tuner: type already set (21) registering 0-0054 tuner: type already set (21) registering 0-0055 tuner: type already set (21) registering 0-0056 tuner: type already set (21) registering 0-0057 registering 1-0050 registering 1-0051 [...] btaudio: driver version 0.7 loaded [digital+analog] btaudio: Bt878 (rev 17) at 00:09.1, irq: 5, latency: 32, mmio: 0xe3005000 btaudio: using card config "default" btaudio: registered device dsp1 [digital] btaudio: registered device dsp2 [analog] btaudio: registered device mixer1 Advanced Linux Sound Architecture Driver Version 1.0.1 (Tue Dec 30 10:04:14 2003 UTC). can't register device seq unable to register OSS mixer device 0:0 ALSA device list: #0: Virtual MIDI Card 1 [...] hub 3-0:1.0: new USB device on port 2, assigned address 2 hub 3-2:1.0: USB hub found hub 3-2:1.0: 4 ports detected hub 3-2:1.0: new USB device on port 1, assigned address 3 drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x04B8 pid 0x0005 hub 3-2:1.0: new USB device on port 3, assigned address 4 drivers/usb/serial/usb-serial.c: descriptor matches drivers/usb/serial/usb-serial.c: found interrupt in drivers/usb/serial/usb-serial.c: found bulk out drivers/usb/serial/usb-serial.c: found bulk in pl2303 3-2.3:1.0: PL-2303 converter detected drivers/usb/serial/usb-serial.c: get_free_serial 1 drivers/usb/serial/usb-serial.c: get_free_serial - minor base = 0 drivers/usb/serial/usb-serial.c: usb_serial_probe - setting up 1 port structures for this device drivers/usb/serial/usb-serial.c: usb_serial_probe - registering ttyUSB0 usb 3-2.3: PL-2303 converter now attached to ttyUSB0 (or usb/tts/0 for devfs) hub 3-2:1.0: new USB device on port 4, assigned address 5 drivers/usb/core/config.c: couldn't get all of config descriptors usb 3-2.4: can't read configurations, error -110 hub 3-2:1.0: new USB device on port 4, assigned address 6 hub 2-0:1.0: new USB device on port 2, assigned address 2 hub 1-0:1.0: new USB device on port 1, assigned address 2 input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:11.2-1 hub 1-0:1.0: new USB device on port 2, assigned address 3 drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x04B8 pid 0x0005 [...] request_module: failed /usr/local/sbin/modprobe -- block-major-8-1. error = 256 hdc: DMA disabled ------------------------------ Yes, there are two usb printers. And dma to hdc did work previously, its my cdr/w drive. Also, the last version of usbutils doesn't show anything because its looking in /proc/bus/usb but everything has now been moved to /sys/bus/usb. I just got this in the messages log for unplugging, and replugging the scanner: Jan 9 12:21:17 coyote kernel: usb 2-2: USB disconnect, address 2 Jan 9 12:21:17 coyote kernel: updfstab: numerical sysctl 1 23 is obsolete. Jan 9 12:21:17 coyote /etc/hotplug/usb.agent: Bad USB agent invocation Jan 9 12:21:43 coyote kernel: hub 2-0:1.0: new USB device on port 2, assigned address 3 Jan 9 12:21:43 coyote /etc/hotplug/usb.agent: Bad USB agent invocation Jan 9 12:21:46 coyote /etc/hotplug/usb.agent: ... no modules for USB product 4b8/10f/100 The installed libusb is now yesterdays cvs. Clues? Do I need a fresher version of usbutils that the 9.7 I just dl'd and ungraded to 10 minutes ago?. Or did I look in the wrong place, it was one of the top choices of a google search. -- Cheers, Gene AMD [EMAIL PROTECTED] 320M [EMAIL PROTECTED] 512M 99.22% setiathome rank, not too shabby for a WV hillbilly Yahoo.com attornies please note, additions to this message by Gene Heskett are: Copyright 2003 by Maurice Eugene Heskett, all rights reserved. ------------------------------------------------------- This SF.net email is sponsored by: Perforce Software. Perforce is the Fast Software Configuration Management System offering advanced branching capabilities and atomic changes on 50+ platforms. Free Eval! http://www.perforce.com/perforce/loadprog.html _______________________________________________ [EMAIL PROTECTED] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
