Hi, i've problem with my Thinkpad A31p, USB and docking station. Without the docking station, USB is working fine, if i plugin my notebook, following errors occur (i remember, that before upgrading to 2.6.3 only one port could be used and with windoze both ports are ok). The error message has occured also with kernels earlier then 2.6.3, but here USB seems to be disabled after identificating one "bad" port.
hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected hub 1-0:1.0: standalone hub hub 1-0:1.0: unknown reserved power switching mode hub 1-0:1.0: individual port over-current protection hub 1-0:1.0: Port indicators are not supported hub 1-0:1.0: power on to power good time: 2ms hub 1-0:1.0: hub controller current requirement: 0mA hub 1-0:1.0: local power source is good hub 1-0:1.0: no over-current condition exists hub 1-0:1.0: enabling power on all ports hub 1-0:1.0: port 1, status 101, change 1, 12 Mb/s uhci_hcd 0000:00:1d.1: root hub device address 1 hub 2-0:1.0: usb_probe_interface hub 2-0:1.0: usb_probe_interface - got id hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected hub 2-0:1.0: standalone hub hub 2-0:1.0: unknown reserved power switching mode hub 2-0:1.0: individual port over-current protection hub 2-0:1.0: Port indicators are not supported hub 2-0:1.0: power on to power good time: 2ms hub 2-0:1.0: hub controller current requirement: 0mA hub 2-0:1.0: local power source is good hub 2-0:1.0: no over-current condition exists hub 2-0:1.0: enabling power on all ports hub 1-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x101 uhci_hcd 0000:00:1d.2: root hub device address 1 hub 1-0:1.0: port 1 not reset yet, waiting 50ms hub 1-0:1.0: port 1 not reset yet, waiting 200ms hub 3-0:1.0: usb_probe_interface hub 3-0:1.0: usb_probe_interface - got id hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected hub 3-0:1.0: standalone hub hub 3-0:1.0: unknown reserved power switching mode hub 3-0:1.0: individual port over-current protection hub 3-0:1.0: Port indicators are not supported hub 3-0:1.0: power on to power good time: 2ms hub 3-0:1.0: hub controller current requirement: 0mA hub 3-0:1.0: local power source is good hub 3-0:1.0: no over-current condition exists hub 3-0:1.0: enabling power on all ports hub 1-0:1.0: port 1 not reset yet, waiting 200ms hub 1-0:1.0: port 1 not reset yet, waiting 200ms hub 1-0:1.0: port 1 not enabled, trying reset again... hub 1-0:1.0: port 1 not reset yet, waiting 200ms hub 1-0:1.0: port 1 not reset yet, waiting 200ms hub 1-0:1.0: port 1 not reset yet, waiting 200ms hub 1-0:1.0: port 1 not enabled, trying reset again... hub 1-0:1.0: port 1 not reset yet, waiting 200ms hub 1-0:1.0: port 1 not reset yet, waiting 200ms hub 1-0:1.0: port 1 not reset yet, waiting 200ms hub 1-0:1.0: port 1 not enabled, trying reset again... hub 1-0:1.0: port 1 not reset yet, waiting 200ms hub 1-0:1.0: port 1 not reset yet, waiting 200ms hub 1-0:1.0: port 1 not reset yet, waiting 200ms hub 1-0:1.0: port 1 not enabled, trying reset again... hub 1-0:1.0: port 1 not reset yet, waiting 200ms hub 1-0:1.0: port 1 not reset yet, waiting 200ms hub 1-0:1.0: port 1 not reset yet, waiting 200ms hub 1-0:1.0: port 1 not enabled, trying reset again... hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad? -- uniorg Solutions GmbH - M�rkische Strasse 237 - 44141 Dortmund [EMAIL PROTECTED] - Tel:0231-9497-262 -- Ein Unternehmen der uniorg-Gruppe ------------------------------------------------------- This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click _______________________________________________ [EMAIL PROTECTED] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
