Hello I am trying to get CardBus running on a PXA-based system. And as a test-card I am using a USB 2.0 CardBus card. Sometimes it works. Or, at least, inserting a USB device produces an expeced result. But sometimes I am getting:
info klogd: cs: cb_alloc(bus 5): vendor 0x1033, device 0x0035 warn klogd: PCI: enabling device 05:00.0 (0000 -> 0002) info klogd: host/usb-ohci-pci.c: usb-05:00.0, PCI device 1033:0035 info klogd: host/usb-ohci.c: USB OHCI at membase 0xc3894000, IRQ 116 info klogd: usb.c: new USB bus registered, assigned bus number 2 info klogd: hub.c: USB hub found info klogd: hub.c: 3 ports detected warn klogd: PCI: enabling device 05:00.1 (0000 -> 0002) info klogd: host/usb-ohci-pci.c: usb-05:00.1, PCI device 1033:0035 info klogd: host/usb-ohci.c: USB OHCI at membase 0xc389a000, IRQ 116 info klogd: usb.c: new USB bus registered, assigned bus number 3 info klogd: hub.c: USB hub found info klogd: hub.c: 2 ports detected warn klogd: PCI: enabling device 05:00.2 (0000 -> 0002) info cardmgr[205]: initializing socket 1 info cardmgr[205]: socket 1: CardBus hotplug device info klogd: hub.c: new USB device 05:00.0-1, assigned address 2 err klogd: host/usb-ohci.c: OHCI Unrecoverable Error, controller usb-05:00.0 disabled warn klogd: usb_control/bulk_msg: timeout err klogd: usb.c: USB device not responding, giving up (error=-108) err klogd: hub.c: Cannot enable port 1 of hub 1, disabling port. err klogd: hub.c: Maybe the USB cable is bad? err klogd: host/usb-ohci.c: 05:00.0 device removed! err klogd: host/usb-ohci.c: 05:00.1 device removed! warn klogd: cs: shutdown_socket(c19b7800) warn klogd: yenta.c.388: map 0, start 0:0, end 1:1 err klogd: ide0: unexpected interrupt, status=0x51, count=11 err klogd: host/usb-ohci.c: 05:00.0 device removed! err klogd: host/usb-ohci.c: 05:00.1 device removed! warn klogd: yenta.c.398: Set io-speed to 0ns info cardmgr[205]: shutting down socket 1 warn klogd: yenta.c.406: offset 0000, map 0, flags 0:0, start 0:0, end 1:1 warn klogd: INTCTL 50, enable 00, IOCTL 00 warn klogd: yenta.c.388: map 1, start 0:0, end 1:1 warn klogd: yenta.c.398: Set io-speed to 0ns warn klogd: yenta.c.406: offset 0000, map 1, flags 0:0, start 0:0, end 1:1 warn klogd: INTCTL 50, enable 00, IOCTL 00 info klogd: usb.c: USB disconnect on device 05:00.0-0 address 1 info klogd: usb.c: USB bus 2 deregistered err klogd: pci_pool_destroy 05:00.0/ohci_td, c38a6000 busy err modprobe: modprobe: Can't locate module char-major-4 info klogd: usb.c: USB disconnect on device 05:00.1-0 address 1 info klogd: usb.c: USB bus 3 deregistered info klogd: cs: cb_free(bus 5) Any idea where to look? Unfortunately, I have no other CardBus cards at the moment, but 16-bit PCMCIA cards work. Thanks Guennadi --------------------------------- Guennadi Liakhovetski, Ph.D. DSA Daten- und Systemtechnik GmbH Pascalstr. 28 D-52076 Aachen Germany ------------------------------------------------------- This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click _______________________________________________ [EMAIL PROTECTED] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
