sumarry: pcmcia usb controler does not work at all

description: NEC USB 2.0 controler on pcmcia (well, it is cardbus exactly) prints 
folowing information
after inserting card into socket:

Jun 22 21:30:15 darkstar PCI: Enabling device 0000:06:00.0 (0000 -> 0002)
Jun 22 21:30:15 darkstar ohci_hcd 0000:06:00.0: NEC Corporation USB
Jun 22 21:30:15 darkstar PCI: Setting latency timer of device 0000:06:00.0 to 64
Jun 22 21:30:15 darkstar ohci_hcd 0000:06:00.0: irq 11, pci mem c8e98000
Jun 22 21:30:15 darkstar ohci_hcd 0000:06:00.0: new USB bus registered, assigned bus 
number 2
Disabling IRQ #11
Jun 22 21:30:15 darkstar hub 2-0:1.0: USB hub found
Jun 22 21:30:15 darkstar hub 2-0:1.0: 3 ports detected
Jun 22 21:30:15 darkstar PCI: Enabling device 0000:06:00.1 (0000 -> 0002)
Jun 22 21:30:15 darkstar ohci_hcd 0000:06:00.1: NEC Corporation USB (#2)
Jun 22 21:30:15 darkstar PCI: Setting latency timer of device 0000:06:00.1 to 64
Jun 22 21:30:15 darkstar ohci_hcd 0000:06:00.1: irq 11, pci mem c8ec0000
Jun 22 21:30:15 darkstar ohci_hcd 0000:06:00.1: new USB bus registered, assigned bus 
number 3
Jun 22 21:30:16 darkstar irq 11: nobody cared!
Jun 22 21:30:16 darkstar [<c010662f>] __report_bad_irq+0x2b/0x67
Jun 22 21:30:16 darkstar [<c01066c7>] note_interrupt+0x43/0x66
Jun 22 21:30:16 darkstar [<c01068cf>] do_IRQ+0x95/0xf9
Jun 22 21:30:16 darkstar [<c01053d4>] common_interrupt+0x18/0x20
Jun 22 21:30:16 darkstar
Jun 22 21:30:16 darkstar handlers:
Jun 22 21:30:16 darkstar [<c8e016dc>] (yenta_interrupt+0x0/0x21 [yenta_socket])
Jun 22 21:30:16 darkstar [<c8cebf5c>] (usb_hcd_irq+0x0/0x4b [usbcore])
Jun 22 21:30:16 darkstar [<c8cebf5c>] (usb_hcd_irq+0x0/0x4b [usbcore])
Jun 22 21:30:16 darkstar Disabling IRQ #11
Jun 22 21:30:16 darkstar hub 3-0:1.0: USB hub found
Jun 22 21:30:16 darkstar hub 3-0:1.0: 2 ports detected
Jun 22 21:30:17 darkstar PCI: Enabling device 0000:06:00.2 (0000 -> 0002)
Jun 22 21:30:17 darkstar ehci_hcd 0000:06:00.2: NEC Corporation USB 2.0
Jun 22 21:30:17 darkstar ehci_hcd 0000:06:00.2: irq 11, pci mem c8ef9000
Jun 22 21:30:17 darkstar ehci_hcd 0000:06:00.2: new USB bus registered, assigned bus 
number 4
Jun 22 21:30:17 darkstar ehci_hcd 0000:06:00.2: USB 2.0 enabled, EHCI 1.00, driver 
2004-May-10
Jun 22 21:30:17 darkstar hub 4-0:1.0: USB hub found
Jun 22 21:30:17 darkstar hub 4-0:1.0: 5 ports detected

when i try to connect some device (kingston pen drive and logitech usb mouse) to it i 
get:

Jun 22 21:31:52 darkstar usb 2-1: new full speed USB device using address 2
Jun 22 21:31:57 darkstar usb 2-1: control timeout on ep0out

and connected device does not work - mouse does not light (it is optical mouse)
nor i can see any scsi devices in dev for usb drive (all necesary modules loaded 
already)

kernel version: 2.6.7 vanilla
distribution: Gentoo Linux 1.4.16

additional information:

cat /proc/version
Linux version 2.6.7 ([EMAIL PROTECTED]) (gcc version 3.4.0 20040601 (Gentoo Hardened 
Linux 3.4.0-r6, ssp-3.4-2, pie-8.7.6.3)) #2 Tue Jun 22 20:14:26 CEST 2004

cat /proc/cpuinfo
processor       : 0
vendor_id       : GenuineIntel
cpu family      : 6
model           : 8
model name      : Pentium III (Coppermine)
stepping        : 3
cpu MHz         : 747.433
cache size      : 256 KB
fdiv_bug        : no
hlt_bug         : no
f00f_bug        : no
coma_bug        : no
fpu             : yes
fpu_exception   : yes
cpuid level     : 2
wp              : yes
flags           : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 
mmx fxsr sse
bogomips        : 1474.56

cat /proc/modules
ds 16708 4 - Live 0xc8f32000
ipt_TOS 2304 16 - Live 0xc8ecd000
usbhid 27680 0 - Live 0xc8f2a000
ipt_LOG 5568 231 - Live 0xc8f06000
ipt_limit 2336 231 - Live 0xc8ef7000
ipt_state 1952 7 - Live 0xc8ef5000
ip_conntrack 30664 1 ipt_state, Live 0xc8efd000
iptable_mangle 2720 1 - Live 0xc8e9a000
iptable_filter 2656 1 - Live 0xc8d2e000
ip_tables 15936 6 ipt_TOS,ipt_LOG,ipt_limit,ipt_state,iptable_mangle,iptable_filter, 
Live 0xc8eed000
ohci_hcd 18564 0 - Live 0xc8ec7000
ehci_hcd 26820 0 - Live 0xc8ee5000
snd_cs46xx 81960 0 - Live 0xc8ecf000
snd_rawmidi 22532 1 snd_cs46xx, Live 0xc8e9c000
snd_ac97_codec 58372 1 snd_cs46xx, Live 0xc8ea8000
gameport 4320 1 snd_cs46xx, Live 0xc8e91000
8250_pci 16704 0 - Live 0xc8e62000
8250 18368 1 8250_pci, Live 0xc8e88000
serial_core 20160 1 8250, Live 0xc8e69000
e100 28032 0 - Live 0xc8e80000
mii 4576 1 e100, Live 0xc8e5f000
yenta_socket 18208 1 - Live 0xc8e01000
pcmcia_core 59284 2 ds,yenta_socket, Live 0xc8e70000
intel_agp 17372 1 - Live 0xc8e0f000
agpgart 29992 1 intel_agp, Live 0xc8e45000
snd_seq_oss 28352 0 - Live 0xc8e07000
snd_seq_midi_event 7200 1 snd_seq_oss, Live 0xc8d62000
snd_seq 45040 4 snd_seq_oss,snd_seq_midi_event, Live 0xc8e39000
snd_seq_device 7368 3 snd_rawmidi,snd_seq_oss,snd_seq, Live 0xc8d3d000
snd_pcm_oss 47176 0 - Live 0xc8e2c000
snd_pcm 83656 2 snd_cs46xx,snd_pcm_oss, Live 0xc8e16000
snd_page_alloc 10568 2 snd_cs46xx,snd_pcm, Live 0xc8d39000
snd_timer 22308 2 snd_seq,snd_pcm, Live 0xc8de3000
snd_mixer_oss 16576 1 snd_pcm_oss, Live 0xc8ddd000
snd 49412 11 
snd_cs46xx,snd_rawmidi,snd_ac97_codec,snd_seq_oss,snd_seq_midi_event,snd_seq,snd_seq_device,snd_pcm_oss,snd_pcm,sn$soundcore
 9312 1 snd, Live 0xc8d35000
ide_cd 36000 1 - Live 0xc8d58000
cdrom 32668 1 ide_cd, Live 0xc8d4f000
floppy 52752 0 - Live 0xc8d41000
evdev 8576 0 - Live 0xc8d2a000
md5 3936 1 - Live 0xc8d28000
ipv6 212512 6 - Live 0xc8d67000
rtc 11448 0 - Live 0xc8d24000
psmouse 16840 0 - Live 0xc8c92000
sd_mod 18496 1 - Live 0xc8c98000
usb_storage 26656 2 - Live 0xc8cb2000
scsi_mod 68092 2 sd_mod,usb_storage, Live 0xc8d01000
uhci_hcd 27632 0 - Live 0xc8caa000
usbcore 97088 7 usbhid,ohci_hcd,ehci_hcd,usb_storage,uhci_hcd, Live 0xc8ce8000
loop 54792 16 - Live 0xc8cbb000
dm_mod 38144 20 - Live 0xc8c9f000

cat /proc/ioports
0000-001f : dma1
0020-0021 : pic1
0040-005f : timer
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : serial
0376-0376 : ide1
03c0-03df : vesafb
03f6-03f6 : ide0
03f8-03ff : serial
04d0-04d1 : pnp 00:0b
0cf8-0cff : PCI conf1
1000-103f : 0000:00:07.3
  1000-103f : pnp 00:0b
1040-105f : 0000:00:07.3
  1040-104f : pnp 00:0b
15e8-15ef : pnp 00:00
1800-183f : 0000:00:03.0
  1800-183f : e100
1840-1847 : 0000:00:03.1
1850-185f : 0000:00:07.1
  1850-1857 : ide0
  1858-185f : ide1
1860-187f : 0000:00:07.2
  1860-187f : uhci_hcd
2000-2fff : PCI Bus #01
  2000-20ff : 0000:01:00.0
4000-40ff : PCI CardBus #02
4400-44ff : PCI CardBus #02
4800-48ff : PCI CardBus #06
4c00-4cff : PCI CardBus #06

[EMAIL PROTECTED] ~ % cat /proc/iomem
00000000-0009f7ff : System RAM
0009f800-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000cffff : Video ROM
000d0000-000d17ff : Adapter ROM
000e0000-000effff : Extension ROM
000f0000-000fffff : System ROM
00100000-07feffff : System RAM
  00100000-0028e641 : Kernel code
  0028e642-00342adf : Kernel data
07ff0000-07ffebff : ACPI Tables
07ffec00-07ffffff : ACPI Non-volatile Storage
10000000-103fffff : PCI CardBus #02
10400000-107fffff : PCI CardBus #02
10800000-10bfffff : PCI CardBus #06
10c00000-10ffffff : PCI CardBus #06
  10c00000-10c00fff : 0000:06:00.0
    10c00000-10c00fff : ohci_hcd
  10c01000-10c01fff : 0000:06:00.1
    10c01000-10c01fff : ohci_hcd
  10c02000-10c020ff : 0000:06:00.2
    10c02000-10c020ff : ehci_hcd
50000000-50000fff : 0000:00:02.0
  50000000-50000fff : yenta_socket
50100000-50100fff : 0000:00:02.1
  50100000-50100fff : yenta_socket
f4000000-f40fffff : 0000:00:05.0
  f4000000-f4002fff : CS46xx_BA1_data0
  f4010000-f40137ff : CS46xx_BA1_data1
  f4020000-f4026fff : CS46xx_BA1_pmem
  f4030000-f40300ff : CS46xx_BA1_reg
f4100000-f411ffff : 0000:00:03.0
  f4100000-f411ffff : e100
f4120000-f4120fff : 0000:00:03.0
  f4120000-f4120fff : e100
f4121000-f4121fff : 0000:00:03.1
f4122000-f4122fff : 0000:00:05.0
  f4122000-f4122fff : CS46xx_BA0
f4200000-f5ffffff : PCI Bus #01
  f4200000-f4200fff : 0000:01:00.0
  f5000000-f5ffffff : 0000:01:00.0
    f5000000-f547ffff : vesafb
f8000000-fbffffff : 0000:00:00.0
fff80000-ffffffff : reserved

lspci -vvv
0000:00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort+ >SERR- <PERR-
        Latency: 64
        Region 0: Memory at f8000000 (32-bit, prefetchable)
        Capabilities: [a0] AGP version 1.0
                Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- 
FW- AGP3- Rate=x1,x2
                Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

0000:00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) 
(prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- 
SERR- FastB2B-
        Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
        Latency: 128
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
        I/O behind bridge: 00002000-00002fff
        Memory behind bridge: f4200000-f5ffffff
        Prefetchable memory behind bridge: fff00000-000fffff
        Expansion ROM at 00002000 [disabled] [size=4K]
        BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B+

0000:00:02.0 CardBus bridge: Texas Instruments PCI1450 (rev 03)
        Subsystem: IBM: Unknown device 0130
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
        Latency: 168, cache line size 08
        Interrupt: pin A routed to IRQ 9
        Region 0: Memory at 50000000 (32-bit, non-prefetchable)
        Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
        Memory window 0: 10000000-103ff000 (prefetchable)
        Memory window 1: 10400000-107ff000
        I/O window 0: 00004000-000040ff
        I/O window 1: 00004400-000044ff
        BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
        16-bit legacy interface ports at 0001

0000:00:02.1 CardBus bridge: Texas Instruments PCI1450 (rev 03)
        Subsystem: IBM: Unknown device 0130
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
        Latency: 168, cache line size 08
        Interrupt: pin B routed to IRQ 11
        Region 0: Memory at 50100000 (32-bit, non-prefetchable)
        Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
        Memory window 0: 10800000-10bff000 (prefetchable)
        Memory window 1: 10c00000-10fff000
        I/O window 0: 00004800-000048ff
        I/O window 1: 00004c00-00004cff
        BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
        16-bit legacy interface ports at 0001

0000:00:03.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 09)
        Subsystem: Intel Corp. EtherExpress PRO/100+ MiniPCI
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- 
SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
        Latency: 66 (2000ns min, 14000ns max), cache line size 08
        Interrupt: pin A routed to IRQ 10
        Region 0: Memory at f4120000 (32-bit, non-prefetchable)
        Region 1: I/O ports at 1800 [size=64]
        Region 2: Memory at f4100000 (32-bit, non-prefetchable) [size=128K]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA 
PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable+ DSel=0 DScale=2 PME-

0000:00:03.1 Serial controller: Xircom Mini-PCI V.90 56k Modem (prog-if 02 [16550])
        Subsystem: Intel Corp.: Unknown device 2408
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
        Interrupt: pin A routed to IRQ 10
        Region 0: I/O ports at 1840
        Region 1: Memory at f4121000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA 
PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-

0000:00:05.0 Multimedia audio controller: Cirrus Logic CS 4614/22/24 [CrystalClear 
SoundFusion Audio Accelerator] (rev 01)
        Subsystem: IBM: Unknown device 0153
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
        Latency: 64 (1000ns min, 6000ns max)
        Interrupt: pin A routed to IRQ 9
        Region 0: Memory at f4122000 (32-bit, non-prefetchable)
        Region 1: Memory at f4000000 (32-bit, non-prefetchable) [size=1M]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:07.0 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
        Latency: 0

0000:00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 
[Master])
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
        Latency: 64
        Region 4: I/O ports at 1850 [size=16]

0000:00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 
[UHCI])
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort+ >SERR- <PERR-
        Latency: 64
        Interrupt: pin D routed to IRQ 5
        Region 4: I/O ports at 1860 [size=32]

0000:00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 03)
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
        Interrupt: pin ? routed to IRQ 9

0000:01:00.0 VGA compatible controller: ATI Technologies Inc Rage Mobility P/M AGP 2x 
(rev 64) (prog-if 00 [VGA])
        Subsystem: IBM ThinkPad A20m
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ 
SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
        Latency: 66 (2000ns min), cache line size 08
        Interrupt: pin A routed to IRQ 9
        Region 0: Memory at f5000000 (32-bit, non-prefetchable)
        Region 1: I/O ports at 2000 [size=256]
        Region 2: Memory at f4200000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [50] AGP version 1.0
                Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- 
FW- AGP3- Rate=x1,x2
                Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
        Capabilities: [5c] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:06:00.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
        Subsystem: NEC Corporation USB
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
        Latency: 64 (250ns min, 10500ns max)
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at 10c00000 (32-bit, non-prefetchable)
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:06:00.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
        Subsystem: NEC Corporation USB
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
        Latency: 64 (250ns min, 10500ns max)
        Interrupt: pin B routed to IRQ 11
        Region 0: Memory at 10c01000 (32-bit, non-prefetchable)
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:06:00.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20 [EHCI])
        Subsystem: Unknown device 1838:1074
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- 
SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
        Latency: 68 (4000ns min, 8500ns max), cache line size 08
        Interrupt: pin C routed to IRQ 11
        Region 0: Memory at 10c02000 (32-bit, non-prefetchable)
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

output of ver_linux:

Linux darkstar 2.6.7 #2 Tue Jun 22 20:14:26 CEST 2004 i686 Pentium III (Coppermine) 
GenuineIntel GNU/Linux

Gnu C                  3.4.0
Gnu make               3.80
binutils               2.15.91.0.1
util-linux             2.12
mount                  2.12a
module-init-tools      3.0
e2fsprogs              1.35
jfsutils               1.1.5
xfsprogs               2.6.3
pcmcia-cs              3.2.5
PPP                    2.4.1
nfs-utils              1.0.6
Linux C Library        2.3.4
Dynamic linker (ldd)   2.3.4
Procps                 3.2.1
Net-tools              1.60
Kbd                    1.12
Sh-utils               5.2.0
Modules Loaded         ds ipt_TOS usbhid ipt_LOG ipt_limit ipt_state ip_conntrack 
iptable_mangle iptable_filter ip_tables ohci_hcd ehci_hcd snd_cs46xx snd_rawmidi 
snd_ac97_codec gameport 8250_pci 8250 serial_core e100 mii yenta_socket pcmcia_core 
intel_agp agpgart snd_seq_oss snd_seq_midi_event snd_seq snd_seq_device snd_pcm_oss 
snd_pcm snd_page_alloc snd_timer snd_mixer_oss snd soundcore ide_cd cdrom floppy evdev 
md5 ipv6 rtc psmouse sd_mod usb_storage scsi_mod uhci_hcd usbcore loop dm_mod


please CC me, i am not subscribed

Albeiro



-------------------------------------------------------
This SF.Net email sponsored by Black Hat Briefings & Training.
Attend Black Hat Briefings & Training, Las Vegas July 24-29 - 
digital self defense, top technical experts, no vendor pitches, 
unmatched networking opportunities. Visit www.blackhat.com
_______________________________________________
[EMAIL PROTECTED]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel

Reply via email to