Am Dienstag, 4. Januar 2005 16:02 schrieb Alan Stern:
> On Mon, 3 Jan 2005, Oliver Neukum wrote:
>
> > Hi,
> >
> > with 2.6.10 (i386/UP/UHCI)
> > 0000:00:1d.0 USB Controller: Intel Corp. 82801DB USB (Hub #1) (rev 03)
> > 0000:00:1d.1 USB Controller: Intel Corp. 82801DB USB (Hub #2) (rev 03)
> > 0000:00:1d.2 USB Controller: Intel Corp. 82801DB USB (Hub #3) (rev 03)
> > 0000:00:1d.7 USB Controller: Intel Corp. 82801DB USB2 (rev 03)
> >
> > my mouse will not work after resumption. Replugging will fix it.
>
> Before suspending, load the UHCI driver with the "debug=3" module
> parameter setting (and make sure you have set CONFIG_USB_DEBUG!). Then
> post the contents of /proc/driver/uhci/... (whichever file corresponds to
> the controller your mouse is plugged into):
>
> before the suspend (and then don't touch the mouse),
HC status
usbcmd = 00c1 Maxp64 CF RS
usbstat = 0000
usbint = 000f
usbfrnum = (1)9d0
flbaseadd = 0c5449d0
sof = 40
stat1 = 01a5 LowSpeed Enabled Connected
stat2 = 0080
Frame List
Skeleton QH's
- skel_int128_qh
[ccbcc000] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int64_qh
[ccbcc030] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int32_qh
[ccbcc060] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int16_qh
[ccbcc090] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int8_qh
[ccbcc0c0] link (0cbcc272) element (00000001)
urbp == NULL
[ccbcc270] link (0cbcc152) element (0ca84040)
0: [cca84040] link (00000001) e3 LS IOC Active NAK Length=7ff MaxLen=5
DT0 EndPt=1 Dev=2, PID=69(IN) (buf=0c0c6000)
- skel_int4_qh
[ccbcc0f0] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int2_qh
[ccbcc120] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int1_qh
[ccbcc150] link (0cbcc182) element (00000001)
urbp == NULL
- skel_ls_control_qh
[ccbcc180] link (0cbcc1b2) element (00000001)
urbp == NULL
- skel_fs_control_qh
[ccbcc1b0] link (0cbcc1e2) element (00000001)
urbp == NULL
- skel_bulk_qh
[ccbcc1e0] link (0cbcc212) element (00000001)
urbp == NULL
- skel_term_qh
[ccbcc210] link (00000001) element (0c4bd000)
urbp == NULL
Main list URBs:
1: urb_priv [cc0e435c] urb [def7db80] qh [ccbcc270] Dev=2 EP=1(IN) INT TDs=1
queued URBs=0
Remove list URBs: Empty
Complete list URBs: Empty
>
> after the suspend (before touching the mouse),
HC status
usbcmd = 0008 Maxp32 EGSM
usbstat = 0020 HCHalted
usbint = 000f
usbfrnum = (1)0a0
flbaseadd = 0c5440a0
sof = 40
stat1 = 0080
stat2 = 0080
Frame List
Skeleton QH's
- skel_int128_qh
[ccbcc000] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int64_qh
[ccbcc030] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int32_qh
[ccbcc060] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int16_qh
[ccbcc090] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int8_qh
[ccbcc0c0] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int4_qh
[ccbcc0f0] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int2_qh
[ccbcc120] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int1_qh
[ccbcc150] link (0cbcc182) element (00000001)
urbp == NULL
- skel_ls_control_qh
[ccbcc180] link (0cbcc1b2) element (00000001)
urbp == NULL
- skel_fs_control_qh
[ccbcc1b0] link (0cbcc1e2) element (00000001)
urbp == NULL
- skel_bulk_qh
[ccbcc1e0] link (0cbcc212) element (00000001)
urbp == NULL
- skel_term_qh
[ccbcc210] link (00000001) element (0c4bd000)
urbp == NULL
Main list URBs: Empty
Remove list URBs: Empty
Complete list URBs: Empty
>
> after moving the mouse.
HC status
usbcmd = 0008 Maxp32 EGSM
usbstat = 0020 HCHalted
usbint = 000f
usbfrnum = (1)0a0
flbaseadd = 0c5440a0
sof = 40
stat1 = 0080
stat2 = 0080
Frame List
Skeleton QH's
- skel_int128_qh
[ccbcc000] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int64_qh
[ccbcc030] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int32_qh
[ccbcc060] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int16_qh
[ccbcc090] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int8_qh
[ccbcc0c0] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int4_qh
[ccbcc0f0] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int2_qh
[ccbcc120] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int1_qh
[ccbcc150] link (0cbcc182) element (00000001)
urbp == NULL
- skel_ls_control_qh
[ccbcc180] link (0cbcc1b2) element (00000001)
urbp == NULL
- skel_fs_control_qh
[ccbcc1b0] link (0cbcc1e2) element (00000001)
urbp == NULL
- skel_bulk_qh
[ccbcc1e0] link (0cbcc212) element (00000001)
urbp == NULL
- skel_term_qh
[ccbcc210] link (00000001) element (0c4bd000)
urbp == NULL
Main list URBs: Empty
Remove list URBs: Empty
Complete list URBs: Empty
After a replug
HC status
usbcmd = 00c1 Maxp64 CF RS
usbstat = 0000
usbint = 000f
usbfrnum = (0)dd0
flbaseadd = 0c544dd0
sof = 40
stat1 = 01a5 LowSpeed Enabled Connected
stat2 = 0080
Frame List
Skeleton QH's
- skel_int128_qh
[ccbcc000] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int64_qh
[ccbcc030] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int32_qh
[ccbcc060] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int16_qh
[ccbcc090] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int8_qh
[ccbcc0c0] link (0cbcc272) element (00000001)
urbp == NULL
[ccbcc270] link (0cbcc152) element (0ca84080)
0: [cca84080] link (00000001) e3 LS IOC Active NAK Length=7ff MaxLen=5
DT0 EndPt=1 Dev=3, PID=69(IN) (buf=0c0c6000)
- skel_int4_qh
[ccbcc0f0] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int2_qh
[ccbcc120] link (0cbcc152) element (00000001)
urbp == NULL
- skel_int1_qh
[ccbcc150] link (0cbcc182) element (00000001)
urbp == NULL
- skel_ls_control_qh
[ccbcc180] link (0cbcc1b2) element (00000001)
urbp == NULL
- skel_fs_control_qh
[ccbcc1b0] link (0cbcc1e2) element (00000001)
urbp == NULL
- skel_bulk_qh
[ccbcc1e0] link (0cbcc212) element (00000001)
urbp == NULL
- skel_term_qh
[ccbcc210] link (00000001) element (0c4bd000)
urbp == NULL
Main list URBs:
1: urb_priv [d178335c] urb [de1efa80] qh [ccbcc270] Dev=3 EP=1(IN) INT TDs=1
queued URBs=0
Remove list URBs: Empty
Complete list URBs: Empty
> There may be a clue in the debug info.
Syslog is looking better:
Jan 4 20:03:41 macbeth kernel: hub 1-0:1.0: USB hub found
Jan 4 20:03:41 macbeth kernel: hub 1-0:1.0: 2 ports detected
Jan 4 20:03:41 macbeth kernel: hub 1-0:1.0: standalone hub
Jan 4 20:03:41 macbeth kernel: hub 1-0:1.0: no power switching (usb 1.0)
Jan 4 20:03:41 macbeth kernel: hub 1-0:1.0: individual port over-current
protection
Jan 4 20:03:41 macbeth kernel: hub 1-0:1.0: power on to power good time: 2ms
Jan 4 20:03:41 macbeth kernel: hub 1-0:1.0: local power source is good
Jan 4 20:03:41 macbeth /etc/hotplug/usb.agent[14296]: need a device for this
command
Jan 4 20:03:41 macbeth kernel: ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 11
(level, low) -> IRQ 11
Jan 4 20:03:41 macbeth kernel: uhci_hcd 0000:00:1d.1: Intel Corp.
82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2
Jan 4 20:03:41 macbeth kernel: hub 1-0:1.0: state 5 ports 2 chg ffff evt ffff
Jan 4 20:03:41 macbeth kernel: uhci_hcd 0000:00:1d.0: port 1 portsc 01a3,00
Jan 4 20:03:41 macbeth kernel: hub 1-0:1.0: port 1, status 0301, change 0001,
1.5 Mb/s
Jan 4 20:03:41 macbeth kernel: PCI: Setting latency timer of device
0000:00:1d.1 to 64
Jan 4 20:03:41 macbeth kernel: uhci_hcd 0000:00:1d.1: irq 11, io base 0x1220
Jan 4 20:03:41 macbeth kernel: uhci_hcd 0000:00:1d.1: new USB bus registered,
assigned bus number 2
Jan 4 20:03:41 macbeth kernel: uhci_hcd 0000:00:1d.1: detected 2 ports
Jan 4 20:03:41 macbeth kernel: usb usb2: new device strings: Mfr=3, Product=2,
SerialNumber=1
Jan 4 20:03:41 macbeth kernel: usb usb2: default language 0x0409
Jan 4 20:03:41 macbeth kernel: usb usb2: Product: Intel Corp. 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2
Jan 4 20:03:41 macbeth kernel: usb usb2: Manufacturer: Linux 2.6.10 uhci_hcd
Jan 4 20:03:41 macbeth kernel: usb usb2: SerialNumber: 0000:00:1d.1
Jan 4 20:03:41 macbeth kernel: usb usb2: hotplug
Jan 4 20:03:41 macbeth kernel: usb usb2: adding 2-0:1.0 (config #1, interface
0)
Jan 4 20:03:41 macbeth kernel: usb 2-0:1.0: hotplug
Jan 4 20:03:41 macbeth kernel: hub 2-0:1.0: usb_probe_interface
Jan 4 20:03:41 macbeth kernel: hub 2-0:1.0: usb_probe_interface - got id
Jan 4 20:03:41 macbeth kernel: hub 2-0:1.0: USB hub found
Jan 4 20:03:41 macbeth kernel: hub 2-0:1.0: 2 ports detected
Jan 4 20:03:41 macbeth kernel: hub 2-0:1.0: standalone hub
Jan 4 20:03:41 macbeth kernel: hub 2-0:1.0: no power switching (usb 1.0)
Jan 4 20:03:41 macbeth kernel: hub 2-0:1.0: individual port over-current
protection
Jan 4 20:03:41 macbeth kernel: hub 2-0:1.0: power on to power good time: 2ms
Jan 4 20:03:41 macbeth kernel: hub 2-0:1.0: local power source is good
Jan 4 20:03:41 macbeth /etc/hotplug/usb.agent[14331]: need a device for this
command
Jan 4 20:03:41 macbeth kernel: hub 1-0:1.0: debounce: port 1: total 100ms
stable 100ms status 0x301
Jan 4 20:03:41 macbeth kernel: ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 11
(level, low) -> IRQ 11
Jan 4 20:03:41 macbeth kernel: uhci_hcd 0000:00:1d.2: Intel Corp.
82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3
Jan 4 20:03:41 macbeth kernel: usb 1-1: new low speed USB device using
uhci_hcd and address 2
Jan 4 20:03:41 macbeth kernel: usb 1-1: skipped 1 descriptor after interface
Jan 4 20:03:41 macbeth kernel: usb 1-1: new device strings: Mfr=1, Product=2,
SerialNumber=0
Jan 4 20:03:41 macbeth kernel: usb 1-1: default language 0x0409
Jan 4 20:03:41 macbeth kernel: usb 1-1: Product: Microsoft IntelliMouse®
Explorer
Jan 4 20:03:41 macbeth kernel: usb 1-1: Manufacturer: Microsoft
Jan 4 20:03:41 macbeth kernel: usb 1-1: hotplug
Jan 4 20:03:41 macbeth kernel: usb 1-1: adding 1-1:1.0 (config #1, interface 0)
Jan 4 20:03:41 macbeth kernel: usb 1-1:1.0: hotplug
Jan 4 20:03:41 macbeth /etc/hotplug/usb.agent[14380]: need a device for this
command
Jan 4 20:03:41 macbeth kernel: usbhid 1-1:1.0: usb_probe_interface
Jan 4 20:03:41 macbeth kernel: usbhid 1-1:1.0: usb_probe_interface - got id
Jan 4 20:03:41 macbeth kernel: uhci_hcd 0000:00:1d.0: uhci_result_control:
failed with status 400000
Jan 4 20:03:41 macbeth kernel: [ccbcc270] link (0cbcc1b2) element (0ca84680)
Jan 4 20:03:41 macbeth kernel: Element != First TD
Jan 4 20:03:41 macbeth kernel: 0: [cca84640] link (0ca84680) e3 LS Length=7
MaxLen=7 DT0 EndPt=0 Dev=2, PID=2d(SETUP) (buf=18e65600)
Jan 4 20:03:41 macbeth kernel: 1: [cca84680] link (00000001) e3 LS IOC
Stalled Length=7ff MaxLen=7ff DT1 EndPt=0 Dev=2, PID=69(IN) (buf=00000000)
Jan 4 20:03:41 macbeth kernel:
Jan 4 20:03:41 macbeth kernel: PCI: Setting latency timer of device
0000:00:1d.2 to 64
Jan 4 20:03:41 macbeth kernel: uhci_hcd 0000:00:1d.2: irq 11, io base 0x1240
Jan 4 20:03:41 macbeth kernel: uhci_hcd 0000:00:1d.0: uhci_result_control:
failed with status 400000
Jan 4 20:03:41 macbeth kernel: [ccbcc240] link (0cbcc1b2) element (0ca84040)
Jan 4 20:03:41 macbeth kernel: Element != First TD
Jan 4 20:03:41 macbeth kernel: 0: [cca84000] link (0ca84040) e3 LS Length=7
MaxLen=7 DT0 EndPt=0 Dev=2, PID=2d(SETUP) (buf=1d00bee0)
Jan 4 20:03:41 macbeth kernel: 1: [cca84040] link (00000001) e3 LS IOC
Stalled Length=7ff MaxLen=7ff DT1 EndPt=0 Dev=2, PID=69(IN) (buf=00000000)
Jan 4 20:03:41 macbeth kernel:
Jan 4 20:03:41 macbeth kernel: uhci_hcd 0000:00:1d.0: uhci_result_control:
failed with status 400000
Jan 4 20:03:41 macbeth kernel: [ccbcc240] link (0cbcc1b2) element (0ca84040)
Jan 4 20:03:41 macbeth kernel: Element != First TD
Jan 4 20:03:41 macbeth kernel: 0: [cca84000] link (0ca84040) e3 LS Length=7
MaxLen=7 DT0 EndPt=0 Dev=2, PID=2d(SETUP) (buf=1d00bee0)
Jan 4 20:03:41 macbeth kernel: 1: [cca84040] link (00000001) e3 LS IOC
Stalled Length=7ff MaxLen=7ff DT1 EndPt=0 Dev=2, PID=69(IN) (buf=00000000)
Jan 4 20:03:41 macbeth kernel:
Jan 4 20:03:41 macbeth kernel: input: USB HID v1.11 Mouse [Microsoft Microsoft
IntelliMouse® Explorer] on usb-0000:00:1d.0-1
Jan 4 20:03:41 macbeth kernel: hub 1-0:1.0: port 2, status 0100, change 0000,
12 Mb/s
Jan 4 20:03:41 macbeth kernel: hub 2-0:1.0: state 5 ports 2 chg ffff evt ffff
Jan 4 20:03:41 macbeth kernel: hub 2-0:1.0: port 1, status 0100, change 0000,
12 Mb/s
Jan 4 20:03:41 macbeth kernel: hub 2-0:1.0: port 2, status 0100, change 0000,
12 Mb/s
Jan 4 20:03:41 macbeth kernel: hub 1-0:1.0: state 5 ports 2 chg fffc evt 0002
Jan 4 20:03:41 macbeth kernel: uhci_hcd 0000:00:1d.2: new USB bus registered,
assigned bus number 3
Jan 4 20:03:41 macbeth kernel: uhci_hcd 0000:00:1d.2: detected 2 ports
Jan 4 20:03:41 macbeth kernel: usb usb3: new device strings: Mfr=3, Product=2,
SerialNumber=1
Jan 4 20:03:41 macbeth kernel: usb usb3: default language 0x0409
Jan 4 20:03:41 macbeth kernel: usb usb3: Product: Intel Corp. 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3
Jan 4 20:03:41 macbeth kernel: usb usb3: Manufacturer: Linux 2.6.10 uhci_hcd
Jan 4 20:03:41 macbeth kernel: usb usb3: SerialNumber: 0000:00:1d.2
Jan 4 20:03:41 macbeth kernel: usb usb3: hotplug
Jan 4 20:03:41 macbeth kernel: usb usb3: adding 3-0:1.0 (config #1, interface
0)
Jan 4 20:03:41 macbeth kernel: usb 3-0:1.0: hotplug
Jan 4 20:03:41 macbeth kernel: hub 3-0:1.0: usb_probe_interface
Jan 4 20:03:41 macbeth kernel: hub 3-0:1.0: usb_probe_interface - got id
Jan 4 20:03:41 macbeth kernel: hub 3-0:1.0: USB hub found
Jan 4 20:03:41 macbeth kernel: hub 3-0:1.0: 2 ports detected
Jan 4 20:03:41 macbeth kernel: hub 3-0:1.0: standalone hub
Jan 4 20:03:41 macbeth kernel: hub 3-0:1.0: no power switching (usb 1.0)
Jan 4 20:03:41 macbeth kernel: hub 3-0:1.0: individual port over-current
protection
Jan 4 20:03:41 macbeth kernel: hub 3-0:1.0: power on to power good time: 2ms
Jan 4 20:03:41 macbeth kernel: hub 3-0:1.0: local power source is good
Jan 4 20:03:41 macbeth /etc/hotplug/usb.agent[14477]: need a device for this
command
Jan 4 20:03:41 macbeth kernel: hub 3-0:1.0: state 5 ports 2 chg ffff evt ffff
Jan 4 20:03:41 macbeth kernel: hub 3-0:1.0: port 1, status 0100, change 0000,
12 Mb/s
Jan 4 20:03:41 macbeth kernel: hub 3-0:1.0: port 2, status 0100, change 0000,
12 Mb/s
Jan 4 20:03:43 macbeth kernel: uhci_hcd 0000:00:1d.1: suspend_hc
Jan 4 20:03:43 macbeth kernel: uhci_hcd 0000:00:1d.2: suspend_hc
Jan 4 20:07:37 macbeth su: pam_unix2: session finished for user root, service
su
Jan 4 20:10:09 macbeth smpppd[4382]: terminating on signal 15
Jan 4 20:10:09 macbeth pppd[4077]: Modem hangup
Jan 4 20:10:09 macbeth pppd[4077]: Couldn't increase MTU to 1500
Jan 4 20:10:09 macbeth pppd[4077]: Couldn't increase MRU to 1500
Jan 4 20:10:09 macbeth pppd[4077]: Connection terminated.
Jan 4 20:10:09 macbeth pppd[4077]: Connect time 7.9 minutes.
Jan 4 20:10:09 macbeth pppd[4077]: Sent 167367 bytes, received 464778 bytes.
Jan 4 20:10:10 macbeth pppd[4077]: Script /etc/ppp/ip-down finished (pid
18625), status = 0x0
Jan 4 20:11:07 macbeth kernel: Stopping tasks:
============================================================================|
Jan 4 20:11:07 macbeth kernel: Freeing memory...
^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^Hdone
(76272 pages freed)
Jan 4 20:11:07 macbeth kernel: usb usb3: no poweroff yet, suspending instead
Jan 4 20:11:07 macbeth kernel: usb 1-1: no poweroff yet, suspending instead
Jan 4 20:11:07 macbeth kernel: usb 1-1: usb suspend
Jan 4 20:11:07 macbeth kernel: usb usb2: no poweroff yet, suspending instead
Jan 4 20:11:07 macbeth kernel: usb usb1: no poweroff yet, suspending instead
Jan 4 20:11:07 macbeth kernel: usb usb4: no poweroff yet, suspending instead
Jan 4 20:11:07 macbeth kernel: radeonfb: suspending to state: 3...
Jan 4 20:11:07 macbeth kernel: agpgart: Found an AGP 2.0 compliant device at
0000:00:00.0.
Jan 4 20:11:07 macbeth kernel: agpgart: Putting AGP V2 device at 0000:00:00.0
into 0x mode
Jan 4 20:11:07 macbeth kernel: agpgart: Putting AGP V2 device at 0000:01:00.0
into 0x mode
Jan 4 20:11:07 macbeth kernel: ehci_hcd 0000:00:1d.7: --> PCI D3hot
Jan 4 20:11:08 macbeth kernel: uhci_hcd 0000:00:1d.2: suspend_hc
Jan 4 20:11:08 macbeth kernel: uhci_hcd 0000:00:1d.2: --> PCI D0/legacy
Jan 4 20:11:08 macbeth kernel: uhci_hcd 0000:00:1d.1: suspend_hc
Jan 4 20:11:08 macbeth kernel: uhci_hcd 0000:00:1d.1: --> PCI D0/legacy
Jan 4 20:11:08 macbeth kernel: uhci_hcd 0000:00:1d.0: suspend_hc
Jan 4 20:11:08 macbeth kernel: uhci_hcd 0000:00:1d.0: --> PCI D0/legacy
Jan 4 20:11:08 macbeth kernel:
..............................................swsusp: Need to copy 7698 pages
Jan 4 20:11:08 macbeth kernel: ..<7>uhci_hcd 0000:00:1d.0: resume from PCI D0
(legacy)
Jan 4 20:11:08 macbeth kernel: PCI: Setting latency timer of device
0000:00:1d.0 to 64
Jan 4 20:11:08 macbeth kernel: uhci_hcd 0000:00:1d.1: resume from PCI D0
(legacy)
Jan 4 20:11:08 macbeth kernel: PCI: Setting latency timer of device
0000:00:1d.1 to 64
Jan 4 20:11:08 macbeth kernel: uhci_hcd 0000:00:1d.2: resume from PCI D0
(legacy)
Jan 4 20:11:08 macbeth kernel: PCI: Setting latency timer of device
0000:00:1d.2 to 64
Jan 4 20:11:08 macbeth kernel: ehci_hcd 0000:00:1d.7: resume from PCI D3hot
Jan 4 20:11:08 macbeth kernel: ehci_hcd 0000:00:1d.7: reset command 080002
(park)=0 ithresh=8 period=1024 Reset HALT
Jan 4 20:11:08 macbeth kernel: ehci_hcd 0000:00:1d.7: reset hcs_params
0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6
Jan 4 20:11:08 macbeth kernel: ehci_hcd 0000:00:1d.7: reset hcc_params 6871
thresh 7 uframes 1024 64 bit addr
Jan 4 20:11:08 macbeth kernel: ehci_hcd 0000:00:1d.7: capability 0001 at 68
Jan 4 20:11:08 macbeth kernel: ehci_hcd 0000:00:1d.7: reset command 080002
(park)=0 ithresh=8 period=1024 Reset HALT
Jan 4 20:11:08 macbeth kernel: PCI: cache line size of 32 is not supported by
device 0000:00:1d.7
Jan 4 20:11:08 macbeth kernel: ehci_hcd 0000:00:1d.7: init command 010001
(park)=0 ithresh=1 period=1024 RUN
Jan 4 20:11:08 macbeth kernel: ehci_hcd 0000:00:1d.7: USB 2.0 restarted, EHCI
1.00, driver 26 Oct 2004
Jan 4 20:11:08 macbeth kernel: ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 11
(level, low) -> IRQ 11
Jan 4 20:11:08 macbeth kernel: PCI: Setting latency timer of device
0000:00:1f.5 to 64
Jan 4 20:11:08 macbeth kernel: uhci_hcd 0000:00:1d.0: wakeup_hc
Jan 4 20:11:08 macbeth kernel: uhci_hcd 0000:00:1d.1: wakeup_hc
Jan 4 20:11:08 macbeth kernel: uhci_hcd 0000:00:1d.2: wakeup_hc
Jan 4 20:11:08 macbeth kernel: ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 11
(level, low) -> IRQ 11
Jan 4 20:11:08 macbeth kernel: PCI: Setting latency timer of device
0000:00:1f.6 to 64
Jan 4 20:11:08 macbeth kernel: radeonfb: resumed !
Jan 4 20:11:08 macbeth kernel: ehci_hcd 0000:00:1d.7: resume root hub
Jan 4 20:11:08 macbeth kernel: uhci_hcd 0000:00:1d.0: port 1 portsc 008a,02
Jan 4 20:11:08 macbeth kernel: usb 1-1: RESUME
Jan 4 20:11:08 macbeth kernel: uhci_hcd 0000:00:1d.0: port 1 portsc 008a,01
Jan 4 20:11:08 macbeth kernel: hub 1-0:1.0: port 1 status 0007.0100 after
resume, 0
Jan 4 20:11:08 macbeth kernel: Restarting tasks...<7>hub 4-0:1.0: state 5
ports 6 chg ffc0 evt ffff
Jan 4 20:11:08 macbeth kernel: hub 1-0:1.0: state 5 ports 2 chg fffc evt ffff
Jan 4 20:11:08 macbeth kernel: uhci_hcd 0000:00:1d.0: port 1 portsc 008a,01
Jan 4 20:11:08 macbeth kernel: usb 1-1: RESUME (wakeup)
Jan 4 20:11:08 macbeth kernel: done
Jan 4 20:11:08 macbeth kernel: usb 1-1: usb resume
Jan 4 20:11:08 macbeth kernel: uhci_hcd 0000:00:1d.0: uhci_result_control:
failed with status 440000
Jan 4 20:11:08 macbeth kernel: [ccbcc240] link (0cbcc1b2) element (0ca84000)
Jan 4 20:11:08 macbeth kernel: 0: [cca84000] link (0ca84040) e0 LS Stalled
CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=2, PID=2d(SETUP) (buf=1c1124a0)
Jan 4 20:11:08 macbeth kernel: 1: [cca84040] link (0ca84080) e3 SPD LS
Active Length=0 MaxLen=1 DT1 EndPt=0 Dev=2, PID=69(IN) (buf=17d56640)
Jan 4 20:11:08 macbeth kernel: 2: [cca84080] link (00000001) e3 LS IOC
Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=2, PID=e1(OUT) (buf=00000000)
Jan 4 20:11:08 macbeth kernel:
Jan 4 20:11:08 macbeth kernel: usb 1-1: gone after usb resume? status -71
Jan 4 20:11:08 macbeth kernel: hub 1-0:1.0: resume on port 1, status -71
Jan 4 20:11:08 macbeth kernel: hub 1-0:1.0: port 1, status 0100, change 0007,
12 Mb/s
Jan 4 20:11:08 macbeth kernel: usb 1-1: USB disconnect, address 2
Jan 4 20:11:08 macbeth kernel: usb 1-1: usb_disable_device nuking all URBs
Jan 4 20:11:08 macbeth kernel: usb 1-1: unregistering interface 1-1:1.0
Jan 4 20:11:08 macbeth kernel: uhci_hcd 0000:00:1d.0: suspend_hc
Jan 4 20:11:08 macbeth kernel: uhci_hcd 0000:00:1d.1: suspend_hc
Jan 4 20:11:08 macbeth kernel: uhci_hcd 0000:00:1d.2: suspend_hc
Jan 4 20:11:08 macbeth kernel: usb 1-1:1.0: hotplug
Jan 4 20:11:08 macbeth kernel: usb 1-1: unregistering device
Jan 4 20:11:08 macbeth kernel: usb 1-1: hotplug
Jan 4 20:11:08 macbeth kernel: hub 1-0:1.0: debounce: port 1: total 100ms
stable 100ms status 0x100
Jan 4 20:11:08 macbeth kernel: hub 2-0:1.0: state 5 ports 2 chg fffc evt ffff
Jan 4 20:11:08 macbeth kernel: hub 3-0:1.0: state 5 ports 2 chg fffc evt ffff
Jan 4 20:11:26 macbeth /etc/hotplug/usb.agent[18745]: need a device for this
command
Jan 4 20:11:35 macbeth kernel: e100: eth0: e100_watchdog: link up, 100Mbps,
full-duplex
Jan 4 20:11:35 macbeth ifup: No configuration found for irlan0
Jan 4 20:11:45 macbeth smpppd[19870]: smpppd version 1.16 started
Jan 4 20:11:46 macbeth kernel: eth0: no IPv6 routers present
Jan 4 20:12:21 macbeth kernel: hub 4-0:1.0: state 5 ports 6 chg ffc0 evt 0002
Jan 4 20:12:21 macbeth kernel: ehci_hcd 0000:00:1d.7: GetStatus port 1 status
001002 POWER sig=se0 CSC
Jan 4 20:12:21 macbeth kernel: hub 4-0:1.0: port 1, status 0100, change 0001,
12 Mb/s
Jan 4 20:12:21 macbeth kernel: hub 4-0:1.0: debounce: port 1: total 100ms
stable 100ms status 0x100
Jan 4 20:12:23 macbeth kernel: hub 4-0:1.0: state 5 ports 6 chg ffc0 evt 0002
Jan 4 20:12:23 macbeth kernel: ehci_hcd 0000:00:1d.7: GetStatus port 1 status
001403 POWER sig=k CSC CONNECT
Jan 4 20:12:23 macbeth kernel: hub 4-0:1.0: port 1, status 0501, change 0001,
480 Mb/s
Jan 4 20:12:23 macbeth kernel: hub 4-0:1.0: debounce: port 1: total 100ms
stable 100ms status 0x501
Jan 4 20:12:23 macbeth kernel: ehci_hcd 0000:00:1d.7: port 1 low speed -->
companion
Jan 4 20:12:23 macbeth kernel: ehci_hcd 0000:00:1d.7: GetStatus port 1 status
003002 POWER OWNER sig=se0 CSC
Jan 4 20:12:23 macbeth kernel: uhci_hcd 0000:00:1d.0: wakeup_hc
Jan 4 20:12:23 macbeth kernel: hub 1-0:1.0: state 5 ports 2 chg fffc evt 0002
Jan 4 20:12:23 macbeth kernel: uhci_hcd 0000:00:1d.0: port 1 portsc 0183,00
Jan 4 20:12:23 macbeth kernel: hub 1-0:1.0: port 1, status 0301, change 0001,
1.5 Mb/s
Jan 4 20:12:23 macbeth kernel: hub 1-0:1.0: debounce: port 1: total 100ms
stable 100ms status 0x301
Jan 4 20:12:23 macbeth kernel: usb 1-1: new low speed USB device using
uhci_hcd and address 3
Jan 4 20:12:24 macbeth kernel: usb 1-1: skipped 1 descriptor after interface
Jan 4 20:12:24 macbeth kernel: usb 1-1: new device strings: Mfr=1, Product=2,
SerialNumber=0
Jan 4 20:12:24 macbeth kernel: usb 1-1: default language 0x0409
Jan 4 20:12:24 macbeth kernel: usb 1-1: Product: Microsoft IntelliMouse®
Explorer
Jan 4 20:12:24 macbeth kernel: usb 1-1: Manufacturer: Microsoft
Jan 4 20:12:24 macbeth kernel: usb 1-1: hotplug
Jan 4 20:12:24 macbeth kernel: usb 1-1: adding 1-1:1.0 (config #1, interface 0)
Jan 4 20:12:24 macbeth kernel: usb 1-1:1.0: hotplug
Jan 4 20:12:24 macbeth kernel: usbhid 1-1:1.0: usb_probe_interface
Jan 4 20:12:24 macbeth kernel: usbhid 1-1:1.0: usb_probe_interface - got id
Jan 4 20:12:24 macbeth /etc/hotplug/usb.agent[20313]: need a device for this
command
Jan 4 20:12:24 macbeth kernel: uhci_hcd 0000:00:1d.0: uhci_result_control:
failed with status 400000
Jan 4 20:12:24 macbeth kernel: [ccbcc240] link (0cbcc1b2) element (0ca84040)
Jan 4 20:12:24 macbeth kernel: Element != First TD
Jan 4 20:12:24 macbeth kernel: 0: [cca84000] link (0ca84040) e3 LS Length=7
MaxLen=7 DT0 EndPt=0 Dev=3, PID=2d(SETUP) (buf=17d56640)
Jan 4 20:12:24 macbeth kernel: 1: [cca84040] link (00000001) e3 LS IOC
Stalled Length=7ff MaxLen=7ff DT1 EndPt=0 Dev=3, PID=69(IN) (buf=00000000)
Jan 4 20:12:24 macbeth kernel:
Jan 4 20:12:24 macbeth kernel: uhci_hcd 0000:00:1d.0: uhci_result_control:
failed with status 400000
Jan 4 20:12:24 macbeth kernel: [ccbcc240] link (0cbcc1b2) element (0ca84040)
Jan 4 20:12:24 macbeth kernel: Element != First TD
Jan 4 20:12:24 macbeth kernel: 0: [cca84000] link (0ca84040) e3 LS Length=7
MaxLen=7 DT0 EndPt=0 Dev=3, PID=2d(SETUP) (buf=194aff20)
Jan 4 20:12:24 macbeth kernel: 1: [cca84040] link (00000001) e3 LS IOC
Stalled Length=7ff MaxLen=7ff DT1 EndPt=0 Dev=3, PID=69(IN) (buf=00000000)
Jan 4 20:12:24 macbeth kernel:
Jan 4 20:12:24 macbeth kernel: uhci_hcd 0000:00:1d.0: uhci_result_control:
failed with status 400000
Jan 4 20:12:24 macbeth kernel: [ccbcc240] link (0cbcc1b2) element (0ca84040)
Jan 4 20:12:24 macbeth kernel: Element != First TD
Jan 4 20:12:24 macbeth kernel: 0: [cca84000] link (0ca84040) e3 LS Length=7
MaxLen=7 DT0 EndPt=0 Dev=3, PID=2d(SETUP) (buf=194aff20)
Jan 4 20:12:24 macbeth kernel: 1: [cca84040] link (00000001) e3 LS IOC
Stalled Length=7ff MaxLen=7ff DT1 EndPt=0 Dev=3, PID=69(IN) (buf=00000000)
Jan 4 20:12:24 macbeth kernel:
Jan 4 20:12:24 macbeth kernel: input: USB HID v1.11 Mouse [Microsoft Microsoft
IntelliMouse® Explorer] on usb-0000:00:1d.0-1
Jan 4 20:12:24 macbeth kernel: hub 1-0:1.0: state 5 ports 2 chg fffc evt 0002
Jan 4 20:15:43 macbeth pppd[4077]: Starting link
Regards
Oliver
-------------------------------------------------------
The SF.Net email is sponsored by: Beat the post-holiday blues
Get a FREE limited edition SourceForge.net t-shirt from ThinkGeek.
It's fun and FREE -- well, almost....http://www.thinkgeek.com/sfshirt
_______________________________________________
[email protected]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
