Begin forwarded message:
Date: Fri, 11 Mar 2005 01:12:48 -0800 From: [EMAIL PROTECTED] To: [EMAIL PROTECTED] Subject: [Bugme-new] [Bug 4325] New: freeze under load - system partialy continues working but no response on keyboard/mouse http://bugme.osdl.org/show_bug.cgi?id=4325 Summary: freeze under load - system partialy continues working but no response on keyboard/mouse Kernel Version: 2.6.10, 2.6.11 (mm,ac, suse patched too) Status: NEW Severity: normal Owner: [EMAIL PROTECTED] Submitter: [EMAIL PROTECTED] Distribution: LFS (www.linuxfromscratch.org) Hardware Environment: everything except Radeon 9200 integrated on MB GA-7N400-Pro2 lspci: 00:00.0 Host bridge: nVidia Corporation nForce2 AGP (different version?) (rev c1) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M] Capabilities: [40] AGP version 3.0 Status: RQ=32 Iso- ArqSz=2 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4 Capabilities: [60] #08 [2001] 00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 1 (rev c1) Subsystem: nVidia Corporation: Unknown device 0c17 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev c1) Subsystem: nVidia Corporation: Unknown device 0c17 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:00.3 RAM memory: nVidia Corporation nForce2 Memory Controller 3 (rev c1) Subsystem: nVidia Corporation: Unknown device 0c17 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:00.4 RAM memory: nVidia Corporation nForce2 Memory Controller 2 (rev c1) Subsystem: nVidia Corporation: Unknown device 0c17 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:00.5 RAM memory: nVidia Corporation nForce2 Memory Controller 5 (rev c1) Subsystem: nVidia Corporation: Unknown device 0c17 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a4) Subsystem: Giga-byte Technology: Unknown device 0c11 Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [48] #08 [01e1] 00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2) Subsystem: Giga-byte Technology: Unknown device 0c11 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 7 Region 0: I/O ports at e000 [size=32] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4) (prog-if 10 [OHCI]) Subsystem: Giga-byte Technology: Unknown device 5004 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 5 Region 0: Memory at e8003000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4) (prog-if 10 [OHCI]) Subsystem: Giga-byte Technology: Unknown device 5004 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin B routed to IRQ 11 Region 0: Memory at e8004000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4) (prog-if 20 [EHCI]) Subsystem: Giga-byte Technology: Unknown device 5004 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin C routed to IRQ 9 Region 0: Memory at e8005000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] #0a [2080] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:06.0 Multimedia audio controller: nVidia Corporation nForce2 AC97 Audio Controler (MCP) (rev a1) Subsystem: Giga-byte Technology: Unknown device a002 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (500ns min, 1250ns max) Interrupt: pin A routed to IRQ 3 Region 0: I/O ports at d000 [size=256] Region 1: I/O ports at d400 [size=128] Region 2: Memory at e8001000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:08.0 PCI bridge: nVidia Corporation nForce2 External PCI Bridge (rev a3) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 00009000-0000bfff Memory behind bridge: e6000000-e7ffffff Prefetchable memory behind bridge: fff00000-000fffff BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- 00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2) (prog-if 8a [Master SecP PriP]) Subsystem: Giga-byte Technology: Unknown device 5002 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Region 4: I/O ports at f000 [size=16] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev c1) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: e4000000-e5ffffff Prefetchable memory behind bridge: d0000000-dfffffff BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- 01:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10) Subsystem: Giga-byte Technology GA-K8VT800 Pro Motherboard Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (8000ns min, 16000ns max), cache line size 10 Interrupt: pin A routed to IRQ 5 Region 0: I/O ports at 9000 [size=256] Region 1: Memory at e7006000 (32-bit, non-prefetchable) [size=256] Expansion ROM at <unassigned> [disabled] [size=64K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 01:0d.0 Unknown mass storage controller: Silicon Image, Inc. (formerly CMD Technology Inc) SiI 3112 [SATALink/SAT Subsystem: Silicon Image, Inc. (formerly CMD Technology Inc) SiI 3112 SATALink Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at a800 [size=8] Region 1: I/O ports at ac00 [size=4] Region 2: I/O ports at b000 [size=8] Region 3: I/O ports at b400 [size=4] Region 4: I/O ports at b800 [size=16] Region 5: Memory at e7004000 (32-bit, non-prefetchable) [size=512] Expansion ROM at <unassigned> [disabled] [size=512K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME- 01:0e.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI Subsystem: Giga-byte Technology: Unknown device 1000 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (500ns min, 1000ns max), cache line size 08 Interrupt: pin A routed to IRQ 5 Region 0: Memory at e7005000 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at e7000000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME+ 02:00.0 VGA compatible controller: ATI Technologies Inc RV280 [Radeon 9200] (rev 01) (prog-if 00 [VGA]) Subsystem: Giga-byte Technology Gigabyte Radeon 9200 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2000ns min), cache line size 08 Interrupt: pin A routed to IRQ 19 Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M] Region 1: I/O ports at c000 [size=256] Region 2: Memory at e5000000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [58] AGP version 3.0 Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 Command: RQ=32 ArqSz=2 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 02:00.1 Display controller: ATI Technologies Inc RV280 [Radeon 9200] (Secondary) (rev 01) Subsystem: Giga-byte Technology: Unknown device 4019 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2000ns min), cache line size 08 Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M] Region 1: Memory at e5010000 (32-bit, non-prefetchable) [size=64K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- HID: (in non conflicting port) usb 3-1.1: new low speed USB device using ohci_hcd and address 3 usb 3-1.2: new low speed USB device using ohci_hcd and address 4 input: USB HID v1.00 Mouse [KYE Genius USB Wheel Mouse] on usb-0000:00:02.1-1.1 input: USB HID v1.10 Keyboard [CHICONY USB Keyboard] on usb-0000:00:02.1-1.2 interrupts: 0: 4440474 IO-APIC-edge timer 2: 0 XT-PIC cascade 3: 1193 IO-APIC-edge NVidia nForce2 ****** probably the problem ?? ****** 5: 27926 IO-APIC-edge ohci1394, ohci_hcd:usb2, eth0 ************************************* 8: 27042 IO-APIC-edge rtc 9: 0 XT-PIC ehci_hcd:usb1 11: 59151 IO-APIC-edge libata, ohci_hcd:usb3 14: 19 IO-APIC-edge ide0 15: 4506 IO-APIC-edge ide1 19: 200000 IO-APIC-level [EMAIL PROTECTED]:2:0:0 NMI: 0 LOC: 4440242 ERR: 0 MIS: 0 Software Environment: (seems not depending on that, tried also newer) Gnu C 3.2.1 Gnu make 3.80 binutils 2.13.2.1 util-linux 2.11y mount 2.11y module-init-tools 3.0 e2fsprogs 1.32 reiserfsprogs 3.6.19 reiser4progs line Linux C Library 2.3.1 Dynamic linker (ldd) 2.3.1 Linux C++ Library 5.0.1 Procps 3.1.5 Net-tools 1.60 Kbd 1.08 Sh-utils 2.0 Problem Description: System stops responsig to user interface and also network connections are broken when heavily using network (ssh upload/download) AND using mouse (i.g.quickly randomly moving) at the same time. The problem doesn't occur when kernel is compiled without ohci_hcd (ehci_hcd is on). In this case mouse(usb) still has basic functionality(no wheel support), even if not shown as HID device by dmesg. I suppose there is some problem with sharing IRQ5 by eth0 and ohci. Tehre are 6 usb ports available. Only two of them cause the problem, probably those which are handled by controller sharing the IRQ5. Steps to reproduce: Start any type downlod/upload of large file(e.g. via gftp ssh connection). Start moving the mouse anytime during the transfer -> system stops resposing and transfer interrupts. The rest of system seems to work unaffected(e.g. clock, animations, cursor blinking, cpu load monitor... ) ------- You are receiving this mail because: ------- You are on the CC list for the bug, or are watching someone who is. ------------------------------------------------------- SF email is sponsored by - The IT Product Guide Read honest & candid reviews on hundreds of IT Products from real users. Discover which products truly live up to the hype. Start reading now. http://ads.osdn.com/?ad_id=6595&alloc_id=14396&op=click _______________________________________________ linux-usb-devel@lists.sourceforge.net To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
