Hi list,
when I plug an external usb-disk (LaCie triple Interface, 160GB), the
following kernel(2.6.14.4) error messages appear:
(I can only provide this information, because it is not my disk and I
have to give it back tomorrow, nevertheless I hope you find this bug
report useful..)
(when replying, please cc me, as I am not subscribed.)
---------clip-------
[ 549.467513] hub 1-0:1.0: state 5 ports 8 chg 0000 evt 0004
[ 549.467522] ehci_hcd 0000:00:10.4: GetStatus port 2 status 001803
POWER sig=j CSC CONNECT
[ 549.467528] hub 1-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
[ 549.518708] hub 1-0:1.0: debounce: port 2: total 100ms stable
100ms status 0x501
[ 549.541207] ehci_hcd 0000:00:10.4: port 2 full speed --> companion
[ 549.541211] ehci_hcd 0000:00:10.4: GetStatus port 2 status 003801
POWER OWNER sig=j CONNECT
[ 549.541222] uhci_hcd 0000:00:10.0: wakeup_rh (auto-start)
[ 549.541234] hub 2-0:1.0: state 5 ports 2 chg 0000 evt 0004
[ 549.541238] uhci_hcd 0000:00:10.0: port 2 portsc 0093,00
[ 549.541242] hub 2-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
[ 549.592310] hub 2-0:1.0: debounce: port 2: total 100ms stable
100ms status 0x101
[ 549.637111] usb 2-2: new full speed USB device using uhci_hcd and
address 2
[ 549.638428] uhci_hcd 0000:00:10.0: uhci_result_control: failed
with status 440000
[ 549.638445] [ffff810002a86300] link (02a86242) element (02a85060)
[ 549.638448] 0: [ffff810002a85060] link (02a850c0) e0 Stalled
CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP)
(buf=5bebf700)
[ 549.638451] 1: [ffff810002a850c0] link (02a85120) e3 SPD Active
Length=0 MaxLen=3f DT1 EndPt=0 Dev=0, PID=69(IN) (buf=4f2ae480)
[ 549.638454] 2: [ffff810002a85120] link (00000001) e3 IOC Active
Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=e1(OUT) (buf=00000000)
[ 549.638457]
[ 549.640027] uhci_hcd 0000:00:10.0: uhci_result_control: failed
with status 440000
[ 549.640041] [ffff810002a86340] link (02a86242) element (02a85180)
[ 549.640044] 0: [ffff810002a85180] link (02a851e0) e0 Stalled
CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP)
(buf=5bebf700)
[ 549.640047] 1: [ffff810002a851e0] link (02a85240) e3 SPD Active
Length=0 MaxLen=3f DT1 EndPt=0 Dev=0, PID=69(IN) (buf=4f2ae480)
[ 549.640051] 2: [ffff810002a85240] link (00000001) e3 IOC Active
Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=e1(OUT) (buf=00000000)
[ 549.640053]
[ 549.641627] uhci_hcd 0000:00:10.0: uhci_result_control: failed
with status 440000
[ 549.641641] [ffff810002a86300] link (02a86242) element (02a85060)
[ 549.641644] 0: [ffff810002a85060] link (02a850c0) e0 Stalled
CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP)
(buf=5bebf700)
[ 549.641647] 1: [ffff810002a850c0] link (02a85120) e3 SPD Active
Length=0 MaxLen=3f DT1 EndPt=0 Dev=0, PID=69(IN) (buf=4f2ae480)
[ 549.641650] 2: [ffff810002a85120] link (00000001) e3 IOC Active
Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=e1(OUT) (buf=00000000)
[ 549.641653]
[ 549.685111] usb 2-2: device descriptor read/64, error -71
[ 549.728029] uhci_hcd 0000:00:10.0: uhci_result_control: failed
with status 440000
[ 549.728045] [ffff810002a86300] link (02a86242) element (02a85060)
[ 549.728048] 0: [ffff810002a85060] link (02a850c0) e0 Stalled
CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP)
(buf=5bebf700)
[ 549.728051] 1: [ffff810002a850c0] link (02a85120) e3 SPD Active
Length=0 MaxLen=3f DT1 EndPt=0 Dev=0, PID=69(IN) (buf=4f2ae480)
[ 549.728055] 2: [ffff810002a85120] link (00000001) e3 IOC Active
Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=e1(OUT) (buf=00000000)
[ 549.728057]
[ 549.729627] uhci_hcd 0000:00:10.0: uhci_result_control: failed
with status 440000
[ 549.729641] [ffff810002a86340] link (02a86242) element (02a85180)
[ 549.729644] 0: [ffff810002a85180] link (02a851e0) e0 Stalled
CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP)
(buf=5bebf700)
[ 549.729647] 1: [ffff810002a851e0] link (02a85240) e3 SPD Active
Length=0 MaxLen=3f DT1 EndPt=0 Dev=0, PID=69(IN) (buf=4f2ae480)
[ 549.729651] 2: [ffff810002a85240] link (00000001) e3 IOC Active
Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=e1(OUT) (buf=00000000)
[ 549.729653]
[ 549.731227] uhci_hcd 0000:00:10.0: uhci_result_control: failed
with status 440000
[ 549.731241] [ffff810002a86300] link (02a86242) element (02a85060)
[ 549.731244] 0: [ffff810002a85060] link (02a850c0) e0 Stalled
CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP)
(buf=5bebf700)
[ 549.731247] 1: [ffff810002a850c0] link (02a85120) e3 SPD Active
Length=0 MaxLen=3f DT1 EndPt=0 Dev=0, PID=69(IN) (buf=4f2ae480)
[ 549.731250] 2: [ffff810002a85120] link (00000001) e3 IOC Active
Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=e1(OUT) (buf=00000000)
[ 549.731253]
[ 549.774714] usb 2-2: device descriptor read/64, error -71
[ 549.838728] hub 2-0:1.0: state 5 ports 2 chg 0000 evt 0004
[ 550.246727] uhci_hcd 0000:00:10.0: suspend_rh (auto-stop)
[ 551.886774] hub 1-0:1.0: state 5 ports 8 chg 0000 evt 0004
[ 551.886782] ehci_hcd 0000:00:10.4: GetStatus port 2 status 001803
POWER sig=j CSC CONNECT
[ 551.886789] hub 1-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
[ 551.937970] hub 1-0:1.0: debounce: port 2: total 100ms stable
100ms status 0x501
[ 551.960480] ehci_hcd 0000:00:10.4: port 2 high speed
[ 551.960485] ehci_hcd 0000:00:10.4: GetStatus port 2 status 001005
POWER sig=se0 PE CONNECT
[ 551.982772] usb 1-2: new high speed USB device using ehci_hcd and
address 3
[ 552.005285] ehci_hcd 0000:00:10.4: port 2 high speed
[ 552.005289] ehci_hcd 0000:00:10.4: GetStatus port 2 status 001005
POWER sig=se0 PE CONNECT
[ 552.036543] usb 1-2: default language 0x0409
[ 552.037243] usb 1-2: new device strings: Mfr=1, Product=2,
SerialNumber=3
[ 552.037246] usb 1-2: Product: USB 2.0 LaCie d2 HD
[ 552.037248] usb 1-2: Manufacturer: LaCie
[ 552.037250] usb 1-2: SerialNumber: 19A00E000885F8AE
[ 552.037263] usb 1-2: hotplug
[ 552.037845] usb 1-2: adding 1-2:1.0 (config #1, interface 0)
[ 552.037853] usb 1-2:1.0: hotplug
[ 552.037987] usb-storage 1-2:1.0: usb_probe_interface
[ 552.037990] usb-storage 1-2:1.0: usb_probe_interface - got id
[ 552.037992] usb-storage: USB Mass Storage device detected
[ 552.038007] usb-storage: -- associate_dev
[ 552.038010] usb-storage: Vendor: 0x059f, Product: 0x0421,
Revision: 0x9abc
[ 552.038012] usb-storage: Interface Subclass: 0x06, Protocol: 0x50
[ 552.038016] usb-storage: Transport: Bulk
[ 552.038018] usb-storage: Protocol: Transparent SCSI
[ 552.038021] usb-storage: usb_stor_control_msg: rq=fe rqtype=a1
value=0000 index=00 len=1
[ 552.038196] usb-storage: GetMaxLUN command result is -32, data is 0
[ 552.038199] usb-storage: usb_stor_control_msg: rq=01 rqtype=02
value=0000 index=81 len=0
[ 552.038445] usb-storage: usb_stor_clear_halt: result = 0
[ 552.038447] usb-storage: usb_stor_control_msg: rq=01 rqtype=02
value=0000 index=01 len=0
[ 552.038644] usb-storage: usb_stor_clear_halt: result = 0
[ 552.052380] scsi6 : SCSI emulation for USB Mass Storage devices
[ 552.052637] usb-storage: *** thread sleeping.
[ 552.052986] usb-storage: device found at 3
[ 552.053029] usb-storage: waiting for device to settle before scanning
[ 554.051650] usb-storage: queuecommand called
[ 554.051656] usb-storage: *** thread awakened.
[ 554.051658] usb-storage: Command INQUIRY (6 bytes)
[ 554.051660] usb-storage: 12 00 00 00 24 00
[ 554.051665] usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F
128 Trg 0 LUN 0 CL 6
[ 554.051668] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
[ 554.051715] usb-storage: Status code 0; transferred 31/31
[ 554.051717] usb-storage: -- transfer complete
[ 554.051719] usb-storage: Bulk command transfer result=0
[ 554.051721] usb-storage: usb_stor_bulk_transfer_sglist: xfer 36
bytes, 1 entries
[ 554.051814] usb-storage: Status code 0; transferred 36/36
[ 554.051816] usb-storage: -- transfer complete
[ 554.051818] usb-storage: Bulk data transfer result 0x0
[ 554.051819] usb-storage: Attempting to get CSW...
[ 554.051821] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
[ 554.051861] usb-storage: Status code 0; transferred 13/13
[ 554.051863] usb-storage: -- transfer complete
[ 554.051865] usb-storage: Bulk status result = 0
[ 554.051867] usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0
[ 554.051869] usb-storage: scsi cmd done, result=0x0
[ 554.051872] usb-storage: *** thread sleeping.
[ 554.052346] Vendor: WDC WD16 Model: 00BB-55FTA0 Rev: 15.0
[ 554.052353] Type: Direct-Access ANSI
SCSI revision: 04
[ 554.052987] usb-storage: queuecommand called
[ 554.052991] usb-storage: *** thread awakened.
[ 554.052993] usb-storage: Command TEST_UNIT_READY (6 bytes)
[ 554.052995] usb-storage: 00 00 00 00 00 00
[ 554.052999] usb-storage: Bulk Command S 0x43425355 T 0x2 L 0 F 0
Trg 0 LUN 0 CL 6
[ 554.053001] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
[ 554.053064] usb-storage: Status code 0; transferred 31/31
[ 554.053066] usb-storage: -- transfer complete
[ 554.053068] usb-storage: Bulk command transfer result=0
[ 554.053070] usb-storage: Attempting to get CSW...
[ 554.053072] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
[ 554.064366] usb-storage: Status code 0; transferred 13/13
[ 554.064368] usb-storage: -- transfer complete
[ 554.064370] usb-storage: Bulk status result = 0
[ 554.064372] usb-storage: Bulk Status S 0x53425355 T 0x2 R 0 Stat 0x0
[ 554.064375] usb-storage: scsi cmd done, result=0x0
[ 554.064377] usb-storage: *** thread sleeping.
[ 554.064456] usb-storage: queuecommand called
[ 554.064822] usb-storage: *** thread awakened.
[ 554.064825] usb-storage: Command READ_CAPACITY (10 bytes)
[ 554.064827] usb-storage: 25 00 00 00 00 00 00 00 00 00
[ 554.064832] usb-storage: Bulk Command S 0x43425355 T 0x3 L 8 F
128 Trg 0 LUN 0 CL 10
[ 554.064835] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
[ 554.064944] usb-storage: Status code 0; transferred 31/31
[ 554.064946] usb-storage: -- transfer complete
[ 554.064948] usb-storage: Bulk command transfer result=0
[ 554.064950] usb-storage: usb_stor_bulk_transfer_sglist: xfer 8
bytes, 1 entries
[ 554.065016] usb-storage: Status code 0; transferred 8/8
[ 554.065018] usb-storage: -- transfer complete
[ 554.065019] usb-storage: Bulk data transfer result 0x0
[ 554.065021] usb-storage: Attempting to get CSW...
[ 554.065023] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
[ 554.065064] usb-storage: Status code 0; transferred 13/13
[ 554.065066] usb-storage: -- transfer complete
[ 554.065067] usb-storage: Bulk status result = 0
[ 554.065069] usb-storage: Bulk Status S 0x53425355 T 0x3 R 0 Stat 0x0
[ 554.065071] usb-storage: scsi cmd done, result=0x0
[ 554.065073] usb-storage: *** thread sleeping.
[ 554.065859] SCSI device sde: 312581808 512-byte hdwr sectors
(160042 MB)
[ 554.065862] sde: assuming drive cache: write through
[ 554.066398] usb-storage: queuecommand called
[ 554.066402] usb-storage: *** thread awakened.
[ 554.066404] usb-storage: Command TEST_UNIT_READY (6 bytes)
[ 554.066406] usb-storage: 00 00 00 00 00 00
[ 554.066410] usb-storage: Bulk Command S 0x43425355 T 0x4 L 0 F 0
Trg 0 LUN 0 CL 6
[ 554.066413] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
[ 554.066465] usb-storage: Status code 0; transferred 31/31
[ 554.066467] usb-storage: -- transfer complete
[ 554.066469] usb-storage: Bulk command transfer result=0
[ 554.066470] usb-storage: Attempting to get CSW...
[ 554.066472] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
[ 554.066915] usb-storage: Status code 0; transferred 13/13
[ 554.066917] usb-storage: -- transfer complete
[ 554.066919] usb-storage: Bulk status result = 0
[ 554.066921] usb-storage: Bulk Status S 0x53425355 T 0x4 R 0 Stat 0x0
[ 554.066923] usb-storage: scsi cmd done, result=0x0
[ 554.066925] usb-storage: *** thread sleeping.
[ 554.067093] usb-storage: queuecommand called
[ 554.067095] usb-storage: *** thread awakened.
[ 554.067097] usb-storage: Command READ_CAPACITY (10 bytes)
[ 554.067099] usb-storage: 25 00 00 00 00 00 00 00 00 00
[ 554.067104] usb-storage: Bulk Command S 0x43425355 T 0x5 L 8 F
128 Trg 0 LUN 0 CL 10
[ 554.067106] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
[ 554.067164] usb-storage: Status code 0; transferred 31/31
[ 554.067166] usb-storage: -- transfer complete
[ 554.067167] usb-storage: Bulk command transfer result=0
[ 554.067169] usb-storage: usb_stor_bulk_transfer_sglist: xfer 8
bytes, 1 entries
[ 554.067215] usb-storage: Status code 0; transferred 8/8
[ 554.067217] usb-storage: -- transfer complete
[ 554.067218] usb-storage: Bulk data transfer result 0x0
[ 554.067220] usb-storage: Attempting to get CSW...
[ 554.067222] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
[ 554.067263] usb-storage: Status code 0; transferred 13/13
[ 554.067265] usb-storage: -- transfer complete
[ 554.067267] usb-storage: Bulk status result = 0
[ 554.067269] usb-storage: Bulk Status S 0x53425355 T 0x5 R 0 Stat 0x0
[ 554.067271] usb-storage: scsi cmd done, result=0x0
[ 554.067273] usb-storage: *** thread sleeping.
[ 554.067636] SCSI device sde: 312581808 512-byte hdwr sectors
(160042 MB)
[ 554.067638] sde: assuming drive cache: write through
[ 554.067640] sde:<7>usb-storage: queuecommand called
[ 554.067656] usb-storage: *** thread awakened.
[ 554.067658] usb-storage: Command READ_10 (10 bytes)
[ 554.067663] usb-storage: 28 00 00 00 00 00 00 00 08 00
[ 554.067668] usb-storage: Bulk Command S 0x43425355 T 0x6 L 4096 F
128 Trg 0 LUN 0 CL 10
[ 554.067670] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
[ 554.067714] usb-storage: Status code 0; transferred 31/31
[ 554.067715] usb-storage: -- transfer complete
[ 554.067717] usb-storage: Bulk command transfer result=0
[ 554.067719] usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096
bytes, 1 entries
[ 554.069914] usb-storage: Status code 0; transferred 4096/4096
[ 554.069916] usb-storage: -- transfer complete
[ 554.069918] usb-storage: Bulk data transfer result 0x0
[ 554.069920] usb-storage: Attempting to get CSW...
[ 554.069922] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
[ 554.069964] usb-storage: Status code 0; transferred 13/13
[ 554.069966] usb-storage: -- transfer complete
[ 554.069967] usb-storage: Bulk status result = 0
[ 554.069970] usb-storage: Bulk Status S 0x53425355 T 0x6 R 0 Stat 0x0
[ 554.069972] usb-storage: scsi cmd done, result=0x0
[ 554.069974] usb-storage: *** thread sleeping.
[ 554.070236] sde1 sde2
[ 554.071025] Attached scsi disk sde at scsi6, channel 0, id 0, lun 0
[ 554.071403] Attached scsi generic sg4 at scsi6, channel 0, id 0,
lun 0, type 0
[ 554.071775] usb-storage: queuecommand called
[ 554.071778] usb-storage: *** thread awakened.
[ 554.071780] usb-storage: Command (unknown command) (12 bytes)
[ 554.071782] usb-storage: a0 00 00 00 00 00 00 00 10 00 00 00
[ 554.071788] usb-storage: Bulk Command S 0x43425355 T 0x7 L 4096 F
128 Trg 0 LUN 0 CL 12
[ 554.071791] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
[ 554.071815] usb-storage: Status code 0; transferred 31/31
[ 554.071817] usb-storage: -- transfer complete
[ 554.071818] usb-storage: Bulk command transfer result=0
[ 554.071821] usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096
bytes, 1 entries
Dec 18 23:06:45 brain scsi.agent[9316]: disk at
/devices/pci0000:00/0000:00:10.4/usb1/1-2/1-2:1.0/host6/target6:0:0/6:0:0:0
[ 554.537133] usb-storage: Status code -32; transferred 0/4096
[ 554.537137] usb-storage: clearing endpoint halt for pipe 0xc0008380
[ 554.537140] usb-storage: usb_stor_control_msg: rq=01 rqtype=02
value=0000 index=81 len=0
[ 554.993544] usb-storage: usb_stor_clear_halt: result = -32
[ 554.993548] usb-storage: Bulk data transfer result 0x4
[ 554.993550] usb-storage: -- transport indicates error, resetting
[ 555.016537] ehci_hcd 0000:00:10.4: port 2 high speed
[ 555.016542] ehci_hcd 0000:00:10.4: GetStatus port 2 status 001005
POWER sig=se0 PE CONNECT
[ 555.038845] usb 1-2: reset high speed USB device using ehci_hcd
and address 3
[ 555.771721] usb 1-2: usb-storage timed out on ep0in len=0/64
[ 556.171699] usb 1-2: usb-storage timed out on ep0in len=0/64
[ 556.194194] ehci_hcd 0000:00:10.4: port 2 high speed
[ 556.194199] ehci_hcd 0000:00:10.4: GetStatus port 2 status 001005
POWER sig=se0 PE CONNECT
[ 556.216474] usb 1-2: device descriptor read/64, error -110
[ 556.470881] usb-storage: command_abort called
[ 557.059810] ehci_hcd 0000:00:10.4: port 2 high speed
[ 557.059816] ehci_hcd 0000:00:10.4: GetStatus port 2 status 001005
POWER sig=se0 PE CONNECT
[ 557.082096] usb 1-2: device descriptor read/64, error -32
[ 557.146221] ehci_hcd 0000:00:10.4: port 2 high speed
[ 557.146226] ehci_hcd 0000:00:10.4: GetStatus port 2 status 001005
POWER sig=se0 PE CONNECT
[ 557.168499] usb 1-2: reset high speed USB device using ehci_hcd
and address 3
[ 557.568536] usb 1-2: usb-storage timed out on ep0in len=0/64
[ 557.650188] ehci_hcd 0000:00:10.4: port 2 high speed
[ 557.650193] ehci_hcd 0000:00:10.4: GetStatus port 2 status 001005
POWER sig=se0 PE CONNECT
[ 557.672511] usb 1-2: device descriptor read/64, error -32
[ 558.631019] ehci_hcd 0000:00:10.4: port 2 high speed
[ 558.631025] ehci_hcd 0000:00:10.4: GetStatus port 2 status 001005
POWER sig=se0 PE CONNECT
[ 558.653338] usb 1-2: device descriptor read/64, error -32
[ 558.717430] ehci_hcd 0000:00:10.4: port 2 high speed
[ 558.717435] ehci_hcd 0000:00:10.4: GetStatus port 2 status 001005
POWER sig=se0 PE CONNECT
[ 558.739737] usb 1-2: reset high speed USB device using ehci_hcd
and address 3
[ 560.071421] usb 1-2: device descriptor read/8, error -32
[ 562.914100] usb 1-2: device descriptor read/8, error -32
[ 562.976748] ehci_hcd 0000:00:10.4: port 2 high speed
[ 562.976754] ehci_hcd 0000:00:10.4: GetStatus port 2 status 001005
POWER sig=se0 PE CONNECT
[ 562.999042] usb 1-2: reset high speed USB device using ehci_hcd
and address 3
[ 563.933735] usb 1-2: device descriptor read/8, error -32
[ 565.320421] usb 1-2: device descriptor read/8, error -32
[ 565.360705] hub 1-0:1.0: logical disconnect on port 2
[ 565.360712] hub 1-0:1.0: state 5 ports 8 chg 0004 evt 0000
[ 565.360717] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
[ 565.360722] usb 1-2: USB disconnect, address 3
[ 565.360724] usb 1-2: usb_disable_device nuking all URBs
[ 565.360729] usb 1-2: unregistering interface 1-2:1.0
[ 565.360744] usb-storage: storage_disconnect() called
[ 565.360746] usb-storage: usb_stor_stop_transport called
[ 565.360749] usb-storage: usb_reset_device returns -19
[ 565.360751] usb-storage: usb_stor_Bulk_reset called
[ 565.360753] usb-storage: No reset during disconnect
[ 565.360756] usb-storage: scsi cmd done, result=0x70000
[ 565.360760] usb-storage: queuecommand called
[ 565.360762] usb-storage: Fail command during disconnect
[ 565.360765] usb-storage: device_reset called
[ 565.360768] usb-storage: usb_stor_Bulk_reset called
[ 565.360770] usb-storage: No reset during disconnect
[ 565.360771] usb-storage: bus_reset called
[ 565.360773] usb-storage: No reset during disconnect
[ 565.360776] scsi: Device offlined - not ready after error
recovery: host 6 channel 0 id 0 lun 0
[ 565.360785] scsi6 (0:0): rejecting I/O to offline device
[ 565.360791] scsi6 (0:0): rejecting I/O to offline device
[ 565.360795] Buffer I/O error on device sde2, logical block 66814080
[ 565.360799] Buffer I/O error on device sde2, logical block 66814081
[ 565.360802] Buffer I/O error on device sde2, logical block 66814082
[ 565.360805] Buffer I/O error on device sde2, logical block 66814083
[ 565.360808] Buffer I/O error on device sde2, logical block 66814084
[ 565.360811] Buffer I/O error on device sde2, logical block 66814085
[ 565.360815] Buffer I/O error on device sde2, logical block 66814086
[ 565.360818] Buffer I/O error on device sde2, logical block 66814087
[ 565.360824] usb-storage: *** thread sleeping.
[ 565.360832] scsi6 (0:0): rejecting I/O to offline device
[ 565.360836] scsi6 (0:0): rejecting I/O to offline device
[ 565.360861] usb-storage: queuecommand called
[ 565.360863] usb-storage: Fail command during disconnect
[ 565.361815] scsi6 (0:0): rejecting I/O to offline device
[ 565.361819] Buffer I/O error on device sde2, logical block 66814080
[ 565.361822] Buffer I/O error on device sde2, logical block 66814081
[ 565.361842] scsi6 (0:0): rejecting I/O to offline device
[ 565.361852] scsi6 (0:0): rejecting I/O to offline device
...etc
--------------- my environment: -------------------------------
Linux brain 2.6.14.4 #4 PREEMPT Sun Dec 18 22:11:40 CET 2005 x86_64
AMD Athlon(tm) 64 Processor 3200+ AuthenticAMD GNU/Linux
--------------- lspci -v | grep HCI
0000:00:0d.0 FireWire (IEEE 1394): Agere Systems FW323 (rev 61)
(prog-if 10 [OHCI])
0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 81) (prog-if 00 [UHCI])
0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 81) (prog-if 00 [UHCI])
0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 81) (prog-if 00 [UHCI])
0000:00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 81) (prog-if 00 [UHCI])
0000:00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
(prog-if 20 [EHCI])
--------------- boot messages:
[ 35.481662] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 35.481690] ehci_hcd 0000:00:10.4: reset hcs_params 0x4208 dbg=0
cc=4 pcc=2 ordered !ppc ports=8
[ 35.481694] ehci_hcd 0000:00:10.4: reset hcc_params 6872 thresh 7
uframes 256/512/1024
[ 35.481703] ehci_hcd 0000:00:10.4: capability 0001 at 68
[ 35.481801] ehci_hcd 0000:00:10.4: new USB bus registered, assigned
bus number 1
[ 35.481837] ehci_hcd 0000:00:10.4: irq 18, io mem 0xf0000400
[ 35.481876] ehci_hcd 0000:00:10.4: reset command 080002 (park)=0
ithresh=8 period=1024 Reset HALT
[ 35.481885] ehci_hcd 0000:00:10.4: init command 010009 (park)=0
ithresh=1 period=256 RUN
[ 35.481890] ehci_hcd 0000:00:10.4: USB 2.0 initialized, EHCI 1.00,
driver 10 Dec 2004
[ 35.481925] ehci_hcd 0000:00:10.4: supports USB remote wakeup
[ 35.481942] usb usb1: default language 0x0409
[ 35.481947] usb usb1: new device strings: Mfr=3, Product=2,
SerialNumber=1
[ 35.481949] usb usb1: Product: EHCI Host Controller
[ 35.481968] usb usb1: Manufacturer: Linux 2.6.14.4 ehci_hcd
[ 35.481987] usb usb1: SerialNumber: 0000:00:10.4
[ 35.482016] usb usb1: hotplug
[ 35.482042] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 35.482050] usb 1-0:1.0: hotplug
[ 35.482068] hub 1-0:1.0: usb_probe_interface
[ 35.482070] hub 1-0:1.0: usb_probe_interface - got id
[ 35.482072] hub 1-0:1.0: USB hub found
[ 35.482111] hub 1-0:1.0: 8 ports detected
[ 35.482128] hub 1-0:1.0: standalone hub
[ 35.482130] hub 1-0:1.0: no power switching (usb 1.0)
[ 35.482132] hub 1-0:1.0: individual port over-current protection
[ 35.482134] hub 1-0:1.0: Single TT
[ 35.482136] hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
[ 35.482138] hub 1-0:1.0: power on to power good time: 20ms
[ 35.482142] hub 1-0:1.0: local power source is good
[ 35.586093] hub 1-0:1.0: state 5 ports 8 chg 0000 evt 0000
[ 35.586138] USB Universal Host Controller Interface driver v2.3
[ 35.586200] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level,
low) -> IRQ 18
[ 35.586236] PCI: Via IRQ fixup for 0000:00:10.0, from 10 to 2
[ 35.586276] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 35.586297] uhci_hcd 0000:00:10.0: detected 2 ports
[ 35.586317] uhci_hcd 0000:00:10.0: check_and_reset_hc: legsup = 0x2000
[ 35.586319] uhci_hcd 0000:00:10.0: Performing full reset
[ 35.586350] uhci_hcd 0000:00:10.0: new USB bus registered, assigned
bus number 2
[ 35.586382] uhci_hcd 0000:00:10.0: irq 18, io base 0x00002c00
[ 35.586426] uhci_hcd 0000:00:10.0: supports USB remote wakeup
[ 35.586433] usb usb2: default language 0x0409
[ 35.586438] usb usb2: new device strings: Mfr=3, Product=2,
SerialNumber=1
[ 35.586440] usb usb2: Product: UHCI Host Controller
[ 35.586458] usb usb2: Manufacturer: Linux 2.6.14.4 uhci_hcd
[ 35.586478] usb usb2: SerialNumber: 0000:00:10.0
[ 35.586502] usb usb2: hotplug
[ 35.586522] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[ 35.586526] usb 2-0:1.0: hotplug
[ 35.586544] hub 2-0:1.0: usb_probe_interface
[ 35.586546] hub 2-0:1.0: usb_probe_interface - got id
[ 35.586548] hub 2-0:1.0: USB hub found
[ 35.586568] hub 2-0:1.0: 2 ports detected
[ 35.586585] hub 2-0:1.0: standalone hub
[ 35.586587] hub 2-0:1.0: no power switching (usb 1.0)
[ 35.586589] hub 2-0:1.0: individual port over-current protection
[ 35.586591] hub 2-0:1.0: power on to power good time: 2ms
[ 35.586594] hub 2-0:1.0: local power source is good
[ 35.690093] hub 2-0:1.0: state 5 ports 2 chg 0000 evt 0000
...etc. (5 hubs)
-------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc. Do you grep through log files
for problems? Stop! Download the new AJAX search engine that makes
searching your log files as easy as surfing the web. DOWNLOAD SPLUNK!
http://ads.osdn.com/?ad_id=7637&alloc_id=16865&op=click
_______________________________________________
linux-usb-devel@lists.sourceforge.net
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
