>> >Can you send the dmesg log for the situation where you boot with the
>> >keyboard and mouse plugged into the computer and the computer
>> >attached to the docking station?
>>
>> Attached as dmesg.init3
>> corresponding devices.init3 attached as well.
>>
>> However, while gathering the dmesg I realized that the
>> keyboard started working some time after I logged in
>> (via network and serial console, not using console kbd)
>>
>> After I realized the keyboard was working I looked in that
>> file again and the keyboard had appeard (devices.init3.diff)
>
>Can you resend this logs from message, perhaps inline? Your
>(or Intel's) Symantec Mail Security program deleted the attachments.
dmesg.init3:
Bootdata ok (command line is root=/dev/hda4 console=tty0 console=ttyS0,115200n8
debug)
Linux version 2.6.15-rc6-gbb44f116 ([EMAIL PROTECTED]) (gcc version 4.0.2
20050901 (prerelease) (SUSE Linux)) #21 SMP Wed Dec 21 00:19:56 EST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ff70000 (usable)
BIOS-e820: 000000001ff70000 - 000000001ff7f000 (ACPI data)
BIOS-e820: 000000001ff7f000 - 000000001ff80000 (ACPI NVS)
BIOS-e820: 000000001ff80000 - 0000000020000000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
ACPI: RSDP (v000 PTLTD ) @ 0x00000000000f7280
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @
0x000000001ff7a87e
ACPI: FADT (v001 NVIDIA CK8 0x06040000 PTL_ 0x000f4240) @
0x000000001ff7ee13
ACPI: MADT (v001 NVIDIA NV_APIC_ 0x06040000 LTP 0x00000000) @
0x000000001ff7ee87
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @
0x000000001ff7eee1
ACPI: SSDT (v001 PTLTD POWERNOW 0x06040000 LTP 0x00000001) @
0x000000001ff7ef09
ACPI: DSDT (v001 NVIDIA CK8 0x06040000 MSFT 0x0100000e) @
0x0000000000000000
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 000000001ff70000
Using 63 for the hash shift.
Using node hash shift of 63
Bootmem setup node 0 0000000000000000-000000001ff70000
No mptable found.
On node 0 totalpages: 127312
DMA zone: 2709 pages, LIFO batch:0
DMA32 zone: 124603 pages, LIFO batch:31
Normal zone: 0 pages, LIFO batch:0
HighMem zone: 0 pages, LIFO batch:0
Nvidia board detected. Ignoring ACPI timer override.
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:4 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: IRQ9 used by override.
Setting APIC routing to physical flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dff80000)
Checking aperture...
CPU 0: aperture @ e8000000 size 128 MB
SMP: Allowing 3 CPUs, 2 hotplug CPUs
Built 1 zonelists
Kernel command line: root=/dev/hda4 console=tty0 console=ttyS0,115200n8 debug
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 65536 bytes)
time.c: Using 3.579545 MHz PM timer.
time.c: Detected 797.953 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Memory: 508260k/523712k available (2948k kernel code, 15064k reserved, 1184k
data, 216k init)
Calibrating delay using timer specific routine.. 1598.12 BogoMIPS (lpj=3196247)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0(1) -> Node 0 -> Core 0
mtrr: v2.0 (20020519)
tbxface-0109 [02] load_tables : ACPI Tables successfully acquired
Parsing all Control
Methods:.............................................................................................................................................................................................................
Table [DSDT](id 0006) - 650 Objects with 66 Devices 205 Methods 24 Regions
Parsing all Control Methods:.
Table [SSDT](id 0004) - 3 Objects with 0 Devices 1 Methods 0 Regions
ACPI Namespace successfully loaded at root ffffffff80554f80
evxfevnt-0091 [03] enable : Transition to ACPI mode successful
Using local APIC timer interrupts.
Detected 12.468 MHz APIC timer.
Brought up 1 CPUs
time.c: Using PIT/TSC based timekeeping.
testing NMI watchdog ... OK.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
evgpeblk-0988 [06] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9
evgpeblk-0996 [06] ev_create_gpe_block : Found 5 Wake, Enabled 1 Runtime GPEs
in this block
evgpeblk-0988 [06] ev_create_gpe_block : GPE 20 to 5F [_GPE] 8 regs on int 0x9
evgpeblk-0996 [06] ev_create_gpe_block : Found 0 Wake, Enabled 1 Runtime GPEs
in this block
Completing Region/Field/Buffer/Package
initialization:.....................................................................
Initialized 24/24 Regions 2/2 Fields 29/29 Buffers 14/21 Packages (662 nodes)
Executing all Device _STA and_INI
methods:......................................................................
70 Devices found containing: 70 _STA, 1 _INI methods
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC0] (gpe 33)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 16 18 19) *0
ACPI: PCI Interrupt Link [LNK2] (IRQs 16 18 19) *0
ACPI: PCI Interrupt Link [LNK3] (IRQs 17) *0
ACPI: PCI Interrupt Link [LNK4] (IRQs 16 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 16 18 19) *0
ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [LMCI] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [LPID] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0C01
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0200
pnp: ACPI device : hid PNP0800
pnp: ACPI device : hid PNP0B00
pnp: ACPI device : hid PNP0C04
pnp: ACPI device : hid PNP0303
pnp: ACPI device : hid PNP0F13
pnp: ACPI device : hid PNP0A05
pnp: ACPI device : hid PNP0700
pnp: ACPI device : hid PNP0501
pnp: ACPI device : hid PNP0401
pnp: PnP ACPI: found 13 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.
agpgart: AGP aperture is 128M @ 0xe8000000
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
pnp: the driver 'system' has been registered
pnp: match found with the PnP device '00:00' and the driver 'system'
pnp: 00:00: ioport range 0x8000-0x807f could not be reserved
pnp: 00:00: ioport range 0x8080-0x80ff has been reserved
pnp: 00:00: ioport range 0x8400-0x847f has been reserved
pnp: 00:00: ioport range 0x8480-0x84ff could not be reserved
pnp: 00:00: ioport range 0x8800-0x887f has been reserved
pnp: 00:00: ioport range 0x8880-0x88ff has been reserved
pnp: 00:00: ioport range 0x2040-0x207f has been reserved
pnp: 00:00: ioport range 0x2000-0x203f has been reserved
pnp: match found with the PnP device '00:01' and the driver 'system'
pnp: match found with the PnP device '00:02' and the driver 'system'
PCI: Failed to allocate mem resource #10:[EMAIL PROTECTED] for 0000:02:04.0
Losing some ticks... checking if CPU frequency changed.
PCI: Failed to allocate mem resource #10:[EMAIL PROTECTED] for 0000:02:04.1
PCI: Bus 3, cardbus bridge: 0000:02:04.0
IO window: 00003000-000030ff
IO window: 00003400-000034ff
PREFETCH window: 30000000-31ffffff
PCI: Bus 7, cardbus bridge: 0000:02:04.1
IO window: 00003800-000038ff
IO window: 00003c00-00003cff
PREFETCH window: 32000000-33ffffff
PCI: Bridge: 0000:00:0a.0
IO window: 3000-7fff
MEM window: e0100000-e17fffff
PREFETCH window: 30000000-33ffffff
PCI: Bridge: 0000:00:0b.0
IO window: disabled.
MEM window: e2000000-e2ffffff
PREFETCH window: f0000000-f80fffff
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 19
GSI 16 sharing vector 0xB1 and IRQ 16
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNK1] -> GSI 19 (level, low) ->
IRQ 177
ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 18
GSI 17 sharing vector 0xB9 and IRQ 17
ACPI: PCI Interrupt 0000:02:04.1[B] -> Link [LNK2] -> GSI 18 (level, low) ->
IRQ 185
Simple Boot Flag at 0x37 set to 0x1
IA-32 Microcode Update Driver: v1.14 <[EMAIL PROTECTED]>
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
ACPI: PCI Interrupt Link [LNK5] enabled at IRQ 16
GSI 18 sharing vector 0xC1 and IRQ 18
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNK5] -> GSI 16 (level, low) ->
IRQ 193
nvidiafb: nVidia device/chipset 10DE0179
nvidiafb: CRTC0 analog not found
nvidiafb: CRTC1 analog not found
nvidiafb: CRTC 1 is currently programmed for DFP
nvidiafb: Using DFP on CRTC 1
Panel size is 1280 x 800
nvidiafb: MTRR set to ON
fbcvt: [EMAIL PROTECTED]: CVT Name - 1.024MA-R
nvidiafb: PCI nVidia NV17 framebuffer (64MB @ 0xF0000000)
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Lid Switch [LID]
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
ACPI: CPU0 (power states: C1[C1] C2[C2])
acpi_thermal-0417 [26] thermal_get_trip_point: Invalid active threshold [0]
ACPI: Thermal Zone [THRM] (41 C)
ibm_acpi: ec object not found
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
pnp: the driver 'i8042 kbd' has been registered
pnp: match found with the PnP device '00:07' and the driver 'i8042 kbd'
pnp: the driver 'i8042 aux' has been registered
pnp: match found with the PnP device '00:08' and the driver 'i8042 aux'
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
pnp: the driver 'serial' has been registered
pnp: match found with the PnP device '00:0b' and the driver 'serial'
00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
acpi_bus-0201 [21] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt Link [LMCI] enabled at IRQ 22
GSI 19 sharing vector 0xC9 and IRQ 19
ACPI: PCI Interrupt 0000:00:06.1[B] -> Link [LMCI] -> GSI 22 (level, low) ->
IRQ 201
ACPI: PCI interrupt for device 0000:00:06.1 disabled
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 6.1.16-k2
Copyright (c) 1999-2005 Intel Corporation.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-150: IDE controller at PCI slot 0000:00:08.0
acpi_bus-0201 [21] bus_set_power : Device is not power manageable
NFORCE3-150: chipset revision 165
NFORCE3-150: not 100% native mode: will probe irqs later
NFORCE3-150: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-150: 0000:00:08.0 (rev a5) UDMA133 controller
ide0: BM-DMA at 0x2080-0x2087, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x2088-0x208f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: HTE726040M9AT00, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-STCD-RW/DVD DRIVE GCC-4241N, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 78140160 sectors (40007 MB) w/7877KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
megaraid cmm: 2.20.2.6 (Release Date: Mon Mar 7 00:01:03 EST 2005)
megaraid: 2.20.4.6 (Release Date: Mon Mar 07 12:27:22 EST 2005)
libata version 1.20 loaded.
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNK1] -> GSI 19 (level, low) ->
IRQ 177
Yenta: CardBus bridge found at 0000:02:04.0 [103c:006d]
PCI: Bus 3, cardbus bridge: 0000:02:04.0
IO window: 00003000-000030ff
IO window: 00003400-000034ff
PREFETCH window: 30000000-31ffffff
MEM window: e0400000-e07fffff
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x01111d22, devctl 0x64
Yenta: ISA IRQ mask 0x0ce8, PCI irq 177
Socket status: 30000086
pcmcia: parent PCI bridge I/O window: 0x3000 - 0x7fff
pcmcia: parent PCI bridge Memory window: 0xe0100000 - 0xe17fffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x33ffffff
ACPI: PCI Interrupt 0000:02:04.1[B] -> Link [LNK2] -> GSI 18 (level, low) ->
IRQ 185
Yenta: CardBus bridge found at 0000:02:04.1 [103c:006d]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.1, mfunc 0x01111d22, devctl 0x64
Yenta: ISA IRQ mask 0x0ce8, PCI irq 185
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x3000 - 0x7fff
pcmcia: parent PCI bridge Memory window: 0xe0100000 - 0xe17fffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x33ffffff
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 3, 32768 bytes)
TCP established hash table entries: 16384 (order: 7, 524288 bytes)
TCP bind hash table entries: 16384 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
input: AT Translated Set 2 keyboard as /class/input/input0
NET: Registered protocol family 17
ACPI wakeup devices:
USB0 USB1 USB2 PS2K PS2M UAR1 MAC0
ACPI: (supports S0 S3 S4 S5)
ReiserFS: hda4: found reiserfs format "3.6" with standard journal
input: PS/2 Mouse as /class/input/input1
input: AlpsPS/2 ALPS GlidePoint as /class/input/input2
ReiserFS: hda4: using ordered data mode
ReiserFS: hda4: journal params: device hda4, size 8192, journal first block 18,
max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda4: checking transaction log (hda4)
ReiserFS: hda4: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 216k freed
Adding 1052248k swap on /dev/hda3. Priority:-1 extents:1 across:1052248k
lp: driver loaded but no devices found
ip_tables: (C) 2000-2002 Netfilter core team
cdrom: open failed.
i2c_adapter i2c-3: nForce2 SMBus adapter at 0x2040
i2c_adapter i2c-4: nForce2 SMBus adapter at 0x2000
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 80 td 96
acpi_bus-0201 [21] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 21
GSI 20 sharing vector 0xD1 and IRQ 20
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 21 (level, low) ->
IRQ 209
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 209, io mem 0xe0000000
ohci_hcd 0000:00:02.0: resetting from state 'reset', control = 0x600
ohci_hcd 0000:00:02.0: OHCI controller state
ohci_hcd 0000:00:02.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:02.0: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:02.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:02.0: intrstatus 0x00000044 RHSC SF
ohci_hcd 0000:00:02.0: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:02.0: hcca frame #0003
ohci_hcd 0000:00:02.0: roothub.a 01000203 POTPGT=1 NPS NDP=3(3)
ohci_hcd 0000:00:02.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:02.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:02.0: roothub.portstatus [0] 0x00010301 CSC LSDA PPS CCS
ohci_hcd 0000:00:02.0: roothub.portstatus [1] 0x00010301 CSC LSDA PPS CCS
ohci_hcd 0000:00:02.0: roothub.portstatus [2] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:02.0: created debug files
ohci_hcd 0000:00:02.0: supports USB remote wakeup
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.15-rc6-gbb44f116 ohci_hcd
usb usb1: SerialNumber: 0000:00:02.0
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
drivers/usb/core/inode.c: creating file '001'
acpi_bus-0201 [21] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 20
GSI 21 sharing vector 0xD9 and IRQ 21
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS1] -> GSI 20 (level, low) ->
IRQ 217
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: OHCI Host Controller
drivers/usb/core/inode.c: creating file '002'
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.1: irq 217, io mem 0xe0001000
ohci_hcd 0000:00:02.1: resetting from state 'reset', control = 0x600
hub 1-0:1.0: state 5 ports 3 chg 0000 evt 0000
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA
PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
ohci_hcd 0000:00:02.1: OHCI controller state
ohci_hcd 0000:00:02.1: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:02.1: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:02.1: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:02.1: intrstatus 0x00000004 SF
ohci_hcd 0000:00:02.1: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:02.1: hcca frame #0003
ohci_hcd 0000:00:02.1: roothub.a 01000203 POTPGT=1 NPS NDP=3(3)
ohci_hcd 0000:00:02.1: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:02.1: roothub.status 00008000 DRWE
ohci_hcd 0000:00:02.1: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:02.1: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:02.1: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:02.1: created debug files
ohci_hcd 0000:00:02.1: supports USB remote wakeup
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.15-rc6-gbb44f116 ohci_hcd
usb usb2: SerialNumber: 0000:00:02.1
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
drivers/usb/core/inode.c: creating file '001'
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA
PPS PES CCS
usb 1-1: new low speed USB device using ohci_hcd and address 2
ohci_hcd 0000:00:02.1: suspend root hub
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA
PPS PES CCS
usb 1-1: skipped 1 descriptor after interface
usb 1-1: default language 0x0409
usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1: Product: USB-PS/2 Optical Mouse
usb 1-1: Manufacturer: Logitech
usb 1-1: hotplug
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: hotplug
drivers/usb/core/inode.c: creating file '002'
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [1] = 0x00010301 CSC LSDA
PPS CCS
hub 1-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301
acpi_bus-0201 [21] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt Link [LACI] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LACI] -> GSI 22 (level, low) ->
IRQ 201
PCI: Setting latency timer of device 0000:00:06.0 to 64
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA
PPS PES CCS
ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
acpi_bus-0201 [21] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [LUS2] -> GSI 21 (level, low) ->
IRQ 209
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: reset hcs_params 0x102486 dbg=1 cc=2 pcc=4 !ppc ports=6
ehci_hcd 0000:00:02.2: reset portroute 0 0 1 1 1 0
ehci_hcd 0000:00:02.2: reset hcc_params a086 caching frame 256/512/1024 park
ehci_hcd 0000:00:02.2: park 0
ehci_hcd 0000:00:02.2: capability 1000001 at a0
PCI: cache line size of 64 is not supported by device 0000:00:02.2
drivers/usb/core/inode.c: creating file '003'
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:02.2: irq 209, io mem 0xe0004000
ehci_hcd 0000:00:02.2: reset command 080b02 park=3 ithresh=8 period=1024 Reset
HALT
ehci_hcd 0000:00:02.2: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: EHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.15-rc6-gbb44f116 ehci_hcd
usb usb3: SerialNumber: 0000:00:02.2
usb usb3: hotplug
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: hotplug
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: Single TT
hub 3-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 3-0:1.0: power on to power good time: 20ms
hub 3-0:1.0: local power source is good
usb 1-2: new low speed USB device using ohci_hcd and address 3
ohci_hcd 0000:00:02.0: urb ffff81001c8b84d0 path 2 ep0in 5ec20000 cc 5 -->
status -110
ohci_hcd 0000:00:02.0: urb ffff81001c8b84d0 path 2 ep0in 5ec20000 cc 5 -->
status -110
ohci_hcd 0000:00:02.0: urb ffff81001c8b84d0 path 2 ep0in 5ec20000 cc 5 -->
status -110
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [1] = 0x00030300 PESC CSC
LSDA PPS
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [2] = 0x00010100 CSC PPS
hub 1-0:1.0: port 3, status 0100, change 0001, 12 Mb/s
drivers/usb/core/inode.c: creating file '001'
hub 1-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x100
hub 2-0:1.0: state 5 ports 3 chg 0000 evt 0000
usbhid 1-1:1.0: usb_probe_interface
usbhid 1-1:1.0: usb_probe_interface - got id
ohci_hcd 0000:00:02.0: urb ffff81001c96a3b8 path 1 ep0out 5ec20000 cc 5 -->
status -110
ohci_hcd 0000:00:02.0: urb ffff81001c96a3b8 path 1 ep0in 5ec20000 cc 5 -->
status -110
ohci_hcd 0000:00:02.0: urb ffff81001c96a3b8 path 1 ep0in 5ec20000 cc 5 -->
status -110
ohci_hcd 0000:00:02.0: urb ffff81001c96a3b8 path 1 ep0in 5ec20000 cc 5 -->
status -110
ohci_hcd 0000:00:02.0: urb ffff81001c96a3b8 path 1 ep0in 5ec20000 cc 5 -->
status -110
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
hub 1-0:1.0: state 5 ports 3 chg 0000 evt 0006
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [0] = 0x00030300 PESC CSC
LSDA PPS
hub 1-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
usb 1-1: USB disconnect, address 2
usb 1-1: usb_disable_device nuking all URBs
usb 1-1: unregistering interface 1-1:1.0
usb 1-1:1.0: hotplug
usb 1-1: unregistering device
usb 1-1: hotplug
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [1] = 0x00030300 PESC CSC
LSDA PPS
hub 1-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
intel8x0_measure_ac97_clock: measured 54881 usecs
intel8x0: clocking to 47465
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300
hub 3-0:1.0: state 5 ports 6 chg 0000 evt 0026
ehci_hcd 0000:00:02.2: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 3-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
ohci_hcd 0000:00:02.0: suspend root hub
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:02.2: port 1 low speed --> companion
ehci_hcd 0000:00:02.2: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
ehci_hcd 0000:00:02.2: GetStatus port 2 status 001403 POWER sig=k CSC CONNECT
hub 3-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:02.2: port 2 low speed --> companion
ehci_hcd 0000:00:02.2: GetStatus port 2 status 003402 POWER OWNER sig=k CSC
ehci_hcd 0000:00:02.2: GetStatus port 5 status 001803 POWER sig=j CSC CONNECT
hub 3-0:1.0: port 5, status 0501, change 0001, 480 Mb/s
hub 3-0:1.0: debounce: port 5: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:02.2: port 5 high speed
ehci_hcd 0000:00:02.2: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT
usb 3-5: new high speed USB device using ehci_hcd and address 4
ohci1394: $Rev: 1313 $ Ben Collins <[EMAIL PROTECTED]>
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNK1] -> GSI 19 (level, low) ->
IRQ 177
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[177] MMIO=[e0108000-e01087ff]
Max Packet=[2048]
usb 3-5: khubd timed out on ep0in len=0/64
8139too Fast Ethernet driver 0.9.27
acpi_bus-0201 [21] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNK2] -> GSI 18 (level, low) ->
IRQ 185
eth0: RealTek RTL8139 at 0x7000, 00:0f:b0:0b:bc:36, IRQ 185
eth0: Identified 8139 chip type 'RTL-8101'
usb 3-5: khubd timed out on ep0in len=0/64
ieee1394: Host added: ID:BUS[0-00:1023] GUID[493f0200493f0200]
usb 3-5: khubd timed out on ep0in len=0/64
ehci_hcd 0000:00:02.2: port 5 high speed
ehci_hcd 0000:00:02.2: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT
usb 3-5: device descriptor read/64, error -110
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
usb 3-5: khubd timed out on ep0in len=0/64
microcode: CPU0 not a capable Intel processor
microcode: No new microcode data for CPU0
usb 3-5: khubd timed out on ep0in len=0/64
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.4)
powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x2 (1500 mV)
powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0xa (1300 mV)
powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x12 (1100 mV)
cpu_init done, current fid 0x0, vid 0x12
eth0: no IPv6 routers present
usb 3-5: khubd timed out on ep0in len=0/64
ehci_hcd 0000:00:02.2: port 5 high speed
ehci_hcd 0000:00:02.2: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT
usb 3-5: device descriptor read/64, error -110
ehci_hcd 0000:00:02.2: port 5 high speed
ehci_hcd 0000:00:02.2: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT
usb 3-5: new high speed USB device using ehci_hcd and address 5
usb 3-5: khubd timed out on ep0in len=0/64
usb 3-5: khubd timed out on ep0in len=0/64
usb 3-5: khubd timed out on ep0in len=0/64
ehci_hcd 0000:00:02.2: port 5 high speed
ehci_hcd 0000:00:02.2: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT
usb 3-5: device descriptor read/64, error -110
usb 3-5: khubd timed out on ep0in len=0/64
usb 3-5: khubd timed out on ep0in len=0/64
usb 3-5: khubd timed out on ep0in len=0/64
ehci_hcd 0000:00:02.2: port 5 high speed
ehci_hcd 0000:00:02.2: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT
usb 3-5: device descriptor read/64, error -110
ehci_hcd 0000:00:02.2: port 5 high speed
ehci_hcd 0000:00:02.2: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT
usb 3-5: new high speed USB device using ehci_hcd and address 6
usb 3-5: khubd timed out on ep0out len=0/0
usb 3-5: khubd timed out on ep0out len=0/0
usb 3-5: device not accepting address 6, error -110
ehci_hcd 0000:00:02.2: port 5 high speed
ehci_hcd 0000:00:02.2: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT
usb 3-5: new high speed USB device using ehci_hcd and address 7
usb 3-5: khubd timed out on ep0out len=0/0
usb 3-5: khubd timed out on ep0out len=0/0
usb 3-5: device not accepting address 7, error -110
hub 1-0:1.0: state 5 ports 3 chg 0000 evt 0000, resume root
ohci_hcd 0000:00:02.0: wakeup
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA
PPS CCS
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [1] = 0x00010301 CSC LSDA
PPS CCS
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA
PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA
PPS PES CCS
usb 1-1: new low speed USB device using ohci_hcd and address 4
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA
PPS PES CCS
usb 1-1: skipped 1 descriptor after interface
usb 1-1: default language 0x0409
usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1: Product: USB-PS/2 Optical Mouse
usb 1-1: Manufacturer: Logitech
usb 1-1: hotplug
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: hotplug
usbhid 1-1:1.0: usb_probe_interface
usbhid 1-1:1.0: usb_probe_interface - got id
input: Logitech USB-PS/2 Optical Mouse as /class/input/input3
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on
usb-0000:00:02.0-1
drivers/usb/core/inode.c: creating file '004'
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [1] = 0x00010301 CSC LSDA
PPS CCS
hub 1-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA
PPS PES CCS
usb 1-2: new low speed USB device using ohci_hcd and address 5
ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA
PPS PES CCS
usb 1-2: skipped 1 descriptor after interface
usb 1-2: skipped 1 descriptor after interface
usb 1-2: skipped 1 descriptor after interface
usb 1-2: default language 0x0409
usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-2: Product: HP Wireless Receiver
usb 1-2: Manufacturer: Chicony
usb 1-2: hotplug
usb 1-2: adding 1-2:1.0 (config #1, interface 0)
usb 1-2:1.0: hotplug
usbhid 1-2:1.0: usb_probe_interface
usbhid 1-2:1.0: usb_probe_interface - got id
input: Chicony HP Wireless Receiver as /class/input/input4
input: USB HID v1.10 Keyboard [Chicony HP Wireless Receiver] on
usb-0000:00:02.0-2
usb 1-2: adding 1-2:1.1 (config #1, interface 1)
usb 1-2:1.1: hotplug
usbhid 1-2:1.1: usb_probe_interface
usbhid 1-2:1.1: usb_probe_interface - got id
usb 1-2: khubd timed out on ep0out len=0/0
drivers/usb/input/hid-core.c: usb_submit_urb(ctrl) failed
drivers/usb/input/hid-core.c: timeout initializing reports
input: Chicony HP Wireless Receiver as /class/input/input5
input: USB HID v1.10 Device [Chicony HP Wireless Receiver] on usb-0000:00:02.0-2
usb 1-2: adding 1-2:1.2 (config #1, interface 2)
usb 1-2:1.2: hotplug
usbhid 1-2:1.2: usb_probe_interface
usbhid 1-2:1.2: usb_probe_interface - got id
input: Chicony HP Wireless Receiver as /class/input/input6
input: USB HID v1.10 Mouse [Chicony HP Wireless Receiver] on usb-0000:00:02.0-2
drivers/usb/core/inode.c: creating file '005'
hub 3-0:1.0: state 5 ports 6 chg 0000 evt 0000
hub 1-0:1.0: state 5 ports 3 chg 0000 evt 0004
devices.init3:
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 6
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.15-rc6-gbb44f116 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=0000:00:02.2
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 3
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.15-rc6-gbb44f116 ohci_hcd
S: Product=OHCI Host Controller
S: SerialNumber=0000:00:02.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 3
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.15-rc6-gbb44f116 ohci_hcd
S: Product=OHCI Host Controller
S: SerialNumber=0000:00:02.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
devices.init3.diff:
25c25
< B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
---
> B: Alloc= 28/900 us ( 3%), #Int= 2, #Iso= 0
33a34,55
>
> T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=1.5 MxCh= 0
> D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
> P: Vendor=046d ProdID=c00e Rev=11.10
> S: Manufacturer=Logitech
> S: Product=USB-PS/2 Optical Mouse
> C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 98mA
> I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=02 Driver=usbhid
> E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=10ms
>
> T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 5 Spd=1.5 MxCh= 0
> D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
> P: Vendor=049f ProdID=008d Rev= 1.00
> S: Manufacturer=Chicony
> S: Product=HP Wireless Receiver
> C:* #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=100mA
> I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=01 Driver=usbhid
> E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=10ms
> I: If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid
> E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=10ms
> I: If#= 2 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=02 Driver=usbhid
> E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl=10ms
-------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc. Do you grep through log files
for problems? Stop! Download the new AJAX search engine that makes
searching your log files as easy as surfing the web. DOWNLOAD SPLUNK!
http://ads.osdn.com/?ad_idv37&alloc_id865&op=click
_______________________________________________
linux-usb-devel@lists.sourceforge.net
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
