Hi, i have a similar card. I somehow figured out that this card in fact has 1k sectors, not 512 bytes (i don't remember how, perhaps with a windows tool or my palm ...). This happens with at least three different card readers which is interesting, because my digital camera when being used as a card reader reports the very same card as having only 512 bytes/sector and twice the number of total sectors. The card works fine when being read through the camera.
Till Am Freitag, 2. Februar 2007 05:25 schrieb Andrew Morton: > Apparently this is a usb-storage problem. > > > Begin forwarded message: > > Date: Thu, 1 Feb 2007 14:00:15 +0100 > From: "Kobajashi Zaghi" <[EMAIL PROTECTED]> > To: [EMAIL PROTECTED] > Cc: [email protected] > Subject: 2 GB SD card problem vs. 2.6.20-rc7 (FAT: Filesystem panic (dev > sdc1)) > > > Hi Pierre! > > I have two 2GB capacity SD card (Kingston, noname). When i put either > of them to a card reader, kernel recognize, but "see" only 1GB > capacity, and when i try to access, FAT filesystem paniced. > > dmesg: > -------- > > [snip] > [ 216.408000] usb 4-3: new high speed USB device using ehci_hcd and > address 3 [ 216.537000] usb 4-3: configuration #1 chosen from 1 choice > [ 216.650000] usbcore: registered new interface driver libusual > [ 216.664000] Initializing USB Mass Storage driver... > [ 216.664000] scsi0 : SCSI emulation for USB Mass Storage devices > [ 216.664000] usbcore: registered new interface driver usb-storage > [ 216.664000] USB Mass Storage support registered. > [ 216.664000] usb-storage: device found at 3 > [ 216.664000] usb-storage: waiting for device to settle before scanning > [ 221.668000] scsi 0:0:0:0: Direct-Access GENERIC USB > Storage-SMC I16A PQ: 0 ANSI: 0 CCS > [ 221.673000] scsi 0:0:0:1: Direct-Access GENERIC USB > Storage-CFC I16A PQ: 0 ANSI: 0 CCS > [ 221.678000] scsi 0:0:0:2: Direct-Access GENERIC USB > Storage-SDC I16A PQ: 0 ANSI: 0 CCS > [ 221.683000] scsi 0:0:0:3: Direct-Access GENERIC USB > Storage-MSC I16A PQ: 0 ANSI: 0 CCS > [ 221.691000] usb-storage: device scan complete > [ 221.792000] sd 0:0:0:0: Attached scsi removable disk sda > [ 221.794000] sd 0:0:0:1: Attached scsi removable disk sdb > [ 221.798000] SCSI device sdc: 1992704 512-byte hdwr sectors (1020 MB) > [ 221.812000] sdc: Write Protect is off > [ 221.812000] sdc: Mode Sense: 00 00 00 00 > [ 221.812000] sdc: assuming drive cache: write through > [ 221.837000] SCSI device sdc: 1992704 512-byte hdwr sectors (1020 MB) > [ 221.849000] sdc: Write Protect is off > [ 221.849000] sdc: Mode Sense: 00 00 00 00 > [ 221.849000] sdc: assuming drive cache: write through > [ 221.849000] sdc: sdc1 > [ 221.851000] sdc: p1 exceeds device capacity > [ 221.852000] sd 0:0:0:2: Attached scsi removable disk sdc > [ 221.854000] sd 0:0:0:3: Attached scsi removable disk sdd > [ 221.878000] sd 0:0:0:0: Attached scsi generic sg0 type 0 > [ 221.879000] sd 0:0:0:1: Attached scsi generic sg1 type 0 > [ 221.879000] sd 0:0:0:2: Attached scsi generic sg2 type 0 > [ 221.879000] sd 0:0:0:3: Attached scsi generic sg3 type 0 > [ 222.030000] attempt to access beyond end of device > [ 222.030000] sdc: rw=0, want=3985272, limit=1992704 > [ 222.030000] Buffer I/O error on device sdc1, logical block 3985024 > [ 222.031000] attempt to access beyond end of device > [ 222.031000] sdc: rw=0, want=3985273, limit=1992704 > [ 222.031000] Buffer I/O error on device sdc1, logical block 3985025 > [ 222.031000] attempt to access beyond end of device > [ 222.031000] sdc: rw=0, want=3985274, limit=1992704 > [ 222.031000] Buffer I/O error on device sdc1, logical block 3985026 > [ 222.031000] attempt to access beyond end of device > [ 222.031000] sdc: rw=0, want=3985275, limit=1992704 > [ 222.031000] Buffer I/O error on device sdc1, logical block 3985027 > [ 222.032000] attempt to access beyond end of device > [ 222.032000] sdc: rw=0, want=3985276, limit=1992704 > [ 222.032000] Buffer I/O error on device sdc1, logical block 3985028 > [...] > [snip] > > lsusb: > ------- > > Bus 004 Device 003: ID 07c4:a600 Datafab Systems, Inc. > Bus 004 Device 001: ID 0000:0000 > Bus 003 Device 001: ID 0000:0000 > Bus 002 Device 001: ID 0000:0000 > Bus 001 Device 003: ID 045e:0040 Microsoft Corp. Wheel Mouse Optical > Bus 001 Device 001: ID 0000:0000 > > lspci > ------ > > 00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML > Express Processor to DRAM Controller (rev 04) > 00:01.0 PCI bridge: Intel Corporation Mobile 915GM/PM Express PCI > Express Root Port (rev 04) > 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > Family) High Definition Audio Controller (rev 04) > 00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > Family) PCI Express Port 1 (rev 04) > 00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > Family) USB UHCI #1 (rev 04) > 00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > Family) USB UHCI #2 (rev 04) > 00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > Family) USB UHCI #3 (rev 04) > 00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > Family) USB2 EHCI Controller (rev 04) > 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d4) > 00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface > Bridge (rev 04) > 00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > Family) IDE Controller (rev 04) > 00:1f.2 IDE interface: Intel Corporation 82801FBM (ICH6M) SATA > Controller (rev 04) > 00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) > SMBus Controller (rev 04) > 01:00.0 VGA compatible controller: ATI Technologies Inc Radeon > Mobility X700 (PCIE) > 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 > PCI-E Gigabit Ethernet Controller (rev 15) > 06:02.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 > IEEE-1394a-2000 Controller (PHY/Link) > 06:03.0 Network controller: Intel Corporation PRO/Wireless 2915ABG > Network Connection (rev 05) > 06:04.0 CardBus bridge: Texas Instruments PCI1620 PC Card Controller (rev > 01) 06:04.1 CardBus bridge: Texas Instruments PCI1620 PC Card Controller > (rev 01) 06:04.2 System peripheral: Texas Instruments PCI1620 Firmware > Loading Function (rev 01) > > cfdisk /dev/sdc > ------------------- > > FATAL ERROR: Bad primary partition 0: Partition ends after end-of-disk > Press > any key to exit cfdisk > > > fdisk /dev/sdc > ----------------- > > The number of cylinders for this disk is set to 2454. > There is nothing wrong with that, but this is larger than 1024, > and could in certain setups cause problems with: > 1) software that runs at boot time (e.g., old versions of LILO) > 2) booting and partitioning software from other OSs > (e.g., DOS FDISK, OS/2 FDISK) > > Command (m for help): p > > Disk /dev/sdc: 1020 MB, 1020264448 bytes > 29 heads, 28 sectors/track, 2454 cylinders > Units = cylinders of 812 * 512 = 415744 bytes > > Device Boot Start End Blocks Id System > /dev/sdc1 1 4909 1992580+ b W95 FAT32 > > > mount -t vfat /dev/sdc1 /media/ > ------------------------------------- > > Feb 1 07:47:03 localhost kernel: [ 421.426000] FAT: Filesystem panic > (dev sdc1) > Feb 1 07:47:03 localhost kernel: [ 421.426000] fat_get_cluster: > invalid cluster chain (i_pos 0) > Feb 1 07:47:03 localhost kernel: [ 421.427000] FAT: Filesystem panic > (dev sdc1) > Feb 1 07:47:03 localhost kernel: [ 421.427000] fat_get_cluster: > invalid cluster chain (i_pos 0) > Feb 1 07:47:34 localhost kernel: [ 452.049000] FAT: Filesystem panic > (dev sdc1) > Feb 1 07:47:34 localhost kernel: [ 452.049000] fat_get_cluster: > invalid cluster chain (i_pos 0) > Feb 1 07:47:34 localhost kernel: [ 452.049000] FAT: Filesystem panic > (dev sdc1) > Feb 1 07:47:34 localhost kernel: [ 452.049000] fat_get_cluster: > invalid cluster chain (i_pos 0) > Feb 1 07:47:34 localhost kernel: [ 452.049000] FAT: Filesystem panic > (dev sdc1) > Feb 1 07:47:34 localhost kernel: [ 452.049000] fat_get_cluster: > invalid cluster chain (i_pos 0) > > dmesg > -------- > > [ 0.000000] Linux version 2.6.20-rc7 ([EMAIL PROTECTED]) (gcc version > 4.1.2 20060928 (prerelease) (Ubuntu 4.1.1-13ubuntu5)) #1 SMP Wed Jan > 31 21:05:44 CET 2007 > [ 0.000000] BIOS-provided physical RAM map: > [ 0.000000] sanitize start > [ 0.000000] sanitize end > [ 0.000000] copy_e820_map() start: 0000000000000000 size: > 000000000009f800 end: 000000000009f800 type: 1 > [ 0.000000] copy_e820_map() type is E820_RAM > [ 0.000000] copy_e820_map() start: 000000000009f800 size: > 0000000000000800 end: 00000000000a0000 type: 2 > [ 0.000000] copy_e820_map() start: 00000000000ce000 size: > 0000000000002000 end: 00000000000d0000 type: 2 > [ 0.000000] copy_e820_map() start: 00000000000dc000 size: > 0000000000024000 end: 0000000000100000 type: 2 > [ 0.000000] copy_e820_map() start: 0000000000100000 size: > 000000003fde0000 end: 000000003fee0000 type: 1 > [ 0.000000] copy_e820_map() type is E820_RAM > [ 0.000000] copy_e820_map() start: 000000003fee0000 size: > 000000000000a000 end: 000000003feea000 type: 3 > [ 0.000000] copy_e820_map() start: 000000003feea000 size: > 0000000000016000 end: 000000003ff00000 type: 4 > [ 0.000000] copy_e820_map() start: 000000003ff00000 size: > 0000000000100000 end: 0000000040000000 type: 2 > [ 0.000000] copy_e820_map() start: 00000000e0000000 size: > 0000000010006000 end: 00000000f0006000 type: 2 > [ 0.000000] copy_e820_map() start: 00000000f0008000 size: > 0000000000004000 end: 00000000f000c000 type: 2 > [ 0.000000] copy_e820_map() start: 00000000fed00000 size: > 0000000000000400 end: 00000000fed00400 type: 2 > [ 0.000000] copy_e820_map() start: 00000000fed20000 size: > 0000000000070000 end: 00000000fed90000 type: 2 > [ 0.000000] copy_e820_map() start: 00000000ff000000 size: > 0000000001000000 end: 0000000100000000 type: 2 > [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable) > [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) > [ 0.000000] BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved) > [ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved) > [ 0.000000] BIOS-e820: 0000000000100000 - 000000003fee0000 (usable) > [ 0.000000] BIOS-e820: 000000003fee0000 - 000000003feea000 (ACPI data) > [ 0.000000] BIOS-e820: 000000003feea000 - 000000003ff00000 (ACPI NVS) > [ 0.000000] BIOS-e820: 000000003ff00000 - 0000000040000000 (reserved) > [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0006000 (reserved) > [ 0.000000] BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved) > [ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved) > [ 0.000000] BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved) > [ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved) > [ 0.000000] 126MB HIGHMEM available. > [ 0.000000] 896MB LOWMEM available. > [ 0.000000] Entering add_active_range(0, 0, 261856) 0 entries of 256 > used [ 0.000000] Zone PFN ranges: > [ 0.000000] DMA 0 -> 4096 > [ 0.000000] Normal 4096 -> 229376 > [ 0.000000] HighMem 229376 -> 261856 > [ 0.000000] early_node_map[1] active PFN ranges > [ 0.000000] 0: 0 -> 261856 > [ 0.000000] On node 0 totalpages: 261856 > [ 0.000000] DMA zone: 32 pages used for memmap > [ 0.000000] DMA zone: 0 pages reserved > [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 > [ 0.000000] Normal zone: 1760 pages used for memmap > [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 > [ 0.000000] HighMem zone: 253 pages used for memmap > [ 0.000000] HighMem zone: 32227 pages, LIFO batch:7 > [ 0.000000] DMI present. > [ 0.000000] ACPI: RSDP (v000 PTLTD > ) @ 0x000f63f0 > [ 0.000000] ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP > 0x00000000) @ 0x3fee4cf5 > [ 0.000000] ACPI: MADT (v001 INTEL ALVISO 0x06040000 LOHR > 0x0000005f) @ 0x3fee9e88 > [ 0.000000] ACPI: FADT (v001 INTEL ALVISO 0x06040000 LOHR > 0x0000005f) @ 0x3fee9ef0 > [ 0.000000] ACPI: HPET (v001 INTEL ALVISO 0x06040000 LOHR > 0x0000005f) @ 0x3fee9f64 > [ 0.000000] ACPI: MCFG (v001 INTEL ALVISO 0x06040000 LOHR > 0x0000005f) @ 0x3fee9f9c > [ 0.000000] ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP > 0x00000001) @ 0x3fee9fd8 > [ 0.000000] ACPI: SSDT (v001 SataRe SataPri 0x00001000 INTL > 0x20030224) @ 0x3fee5b87 > [ 0.000000] ACPI: SSDT (v001 SataRe SataSec 0x00001000 INTL > 0x20030224) @ 0x3fee54eb > [ 0.000000] ACPI: SSDT (v001 PmRef Cpu0Ist 0x00003000 INTL > 0x20030224) @ 0x3fee50a6 > [ 0.000000] ACPI: SSDT (v001 PmRef Cpu0Cst 0x00003001 INTL > 0x20030224) @ 0x3fee4f5a > [ 0.000000] ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL > 0x20030224) @ 0x3fee4d41 > [ 0.000000] ACPI: DSDT (v001 INTEL ALVISO 0x06040000 INTL > 0x20030224) @ 0x00000000 > [ 0.000000] ACPI: PM-Timer IO Port: 0x1008 > [ 0.000000] ACPI: Local APIC address 0xfee00000 > [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) > [ 0.000000] Processor #0 6:13 APIC version 20 > [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled) > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) > [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) > [ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI > 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl > dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high > level) [ 0.000000] ACPI: IRQ0 used by override. > [ 0.000000] ACPI: IRQ2 used by override. > [ 0.000000] ACPI: IRQ9 used by override. > [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs > [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0x0 > [ 0.000000] Using ACPI (MADT) for SMP configuration information > [ 0.000000] Allocating PCI resources starting at 50000000 (gap: > 40000000:a0000000) > [ 0.000000] Detected 1729.177 MHz processor. > [ 16.440639] Built 1 zonelists. Total pages: 259811 > [ 16.440643] Kernel command line: > root=UUID=3b6c3c49-cca7-4e4e-a451-e577a29a8dc6 ro vga=791 > [ 16.440799] mapped APIC to ffffd000 (fee00000) > [ 16.440801] mapped IOAPIC to ffffc000 (fec00000) > [ 16.440805] Enabling fast FPU save and restore... done. > [ 16.440807] Enabling unmasked SIMD FPU exception support... done. > [ 16.440816] Initializing CPU#0 > [ 16.440890] PID hash table entries: 4096 (order: 12, 16384 bytes) > [ 16.441012] Console: colour dummy device 80x25 > [ 16.441433] Dentry cache hash table entries: 131072 (order: 7, 524288 > bytes) [ 16.441849] Inode-cache hash table entries: 65536 (order: 6, > 262144 bytes) [ 16.472311] Memory: 1027704k/1047424k available (1950k > kernel code, 18980k reserved, 878k data, 316k init, 129920k highmem) > [ 16.472326] virtual kernel memory layout: > [ 16.472327] fixmap : 0xfff4f000 - 0xfffff000 ( 704 kB) > [ 16.472329] pkmap : 0xff800000 - 0xffc00000 (4096 kB) > [ 16.472330] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) > [ 16.472331] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) > [ 16.472332] .init : 0xc03ca000 - 0xc0419000 ( 316 kB) > [ 16.472334] .data : 0xc02e7b50 - 0xc03c36d4 ( 878 kB) > [ 16.472335] .text : 0xc0100000 - 0xc02e7b50 (1950 kB) > [ 16.472351] Checking if this processor honours the WP bit even in > supervisor mode... Ok. > [ 16.531845] Calibrating delay using timer specific routine.. > 3460.15 BogoMIPS (lpj=1730075) > [ 16.531884] Security Framework v1.0.0 initialized > [ 16.531893] SELinux: Disabled at boot. > [ 16.531908] Mount-cache hash table entries: 512 > [ 16.532025] CPU: After generic identify, caps: afe9fbff 00100000 > 00000000 00000000 00000180 00000000 00000000 > [ 16.532036] CPU: L1 I cache: 32K, L1 D cache: 32K > [ 16.532041] CPU: L2 cache: 2048K > [ 16.532045] CPU: After all inits, caps: afe9fbff 00100000 00000000 > 00002040 00000180 00000000 00000000 > [ 16.532053] Compat vDSO mapped to ffffe000. > [ 16.532065] Checking 'hlt' instruction... OK. > [ 16.535925] SMP alternatives: switching to UP code > [ 16.536099] Freeing SMP alternatives: 12k freed > [ 16.536103] ACPI: Core revision 20060707 > [ 16.543659] CPU0: Intel(R) Pentium(R) M processor 1.73GHz stepping 08 > [ 16.543685] Total of 1 processors activated (3460.15 BogoMIPS). > [ 16.543881] ENABLING IO-APIC IRQs > [ 16.544079] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 > [ 16.658811] Brought up 1 CPUs > [ 16.659048] NET: Registered protocol family 16 > [ 16.659122] EISA bus registered > [ 16.659128] ACPI: bus type pci registered > [ 16.659138] PCI: Using MMCONFIG > [ 16.659787] Setting up standard PCI resources > [ 16.668332] ACPI: Interpreter enabled > [ 16.668336] ACPI: Using IOAPIC for interrupt routing > [ 16.668944] ACPI: PCI Root Bridge [PCI0] (0000:00) > [ 16.668951] PCI: Probing PCI hardware (bus 00) > [ 16.669968] PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO > [ 16.669974] PCI quirk: region 1180-11bf claimed by ICH6 GPIO > [ 16.670167] Boot video device is 0000:01:00.0 > [ 16.670700] PCI: Transparent bridge - 0000:00:1e.0 > [ 16.670788] PCI: Bus #07 (-#0a) is hidden behind transparent bridge > #06 (-#06) (try 'pci=assign-busses') > [ 16.670794] Please report the result to linux-kernel to fix this > permanently [ 16.670836] PCI: Bus #0b (-#0e) is hidden behind transparent > bridge #06 (-#06) (try 'pci=assign-busses') > [ 16.670842] Please report the result to linux-kernel to fix this > permanently [ 16.670873] ACPI: PCI Interrupt Routing Table > [\_SB_.PCI0._PRT] [ 16.672744] ACPI: PCI Interrupt Routing Table > [\_SB_.PCI0.PEGP._PRT] [ 16.673121] ACPI: PCI Interrupt Routing Table > [\_SB_.PCI0.RP01._PRT] [ 16.673351] ACPI: PCI Interrupt Routing Table > [\_SB_.PCI0.PCIB._PRT] [ 16.673860] ACPI: PCI Interrupt Link [LNKA] (IRQs > 1 3 *4 5 6 7 10 12 14 15) [ 16.674073] ACPI: PCI Interrupt Link [LNKB] > (IRQs 1 3 4 5 6 7 *11 12 14 15) [ 16.674292] ACPI: PCI Interrupt Link > [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 > [ 16.674501] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 > 14 15) *10 > [ 16.674709] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 *10 12 14 > 15) [ 16.674921] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 > 14 15) *10 > [ 16.675129] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 > 14 15) *0, disabled. > [ 16.675340] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 *5 6 7 11 12 14 > 15) [ 16.676954] Linux Plug and Play Support v0.97 (c) Adam Belay > [ 16.676967] pnp: PnP ACPI init > [ 16.679339] pnp: PnP ACPI: found 12 devices > [ 16.679345] PnPBIOS: Disabled by ACPI PNP > [ 16.679385] PCI: Using ACPI for IRQ routing > [ 16.679390] PCI: If a device doesn't work, try "pci=routeirq". If > it helps, post a report > [ 16.679783] PCI: Bridge: 0000:00:01.0 > [ 16.679787] IO window: 2000-2fff > [ 16.679791] MEM window: c0100000-c01fffff > [ 16.679796] PREFETCH window: d0000000-d7ffffff > [ 16.679800] PCI: Bridge: 0000:00:1c.0 > [ 16.679804] IO window: 3000-3fff > [ 16.679810] MEM window: c4000000-c7ffffff > [ 16.679815] PREFETCH window: d8000000-dbffffff > [ 16.679832] PCI: Bus 7, cardbus bridge: 0000:06:04.0 > [ 16.679836] IO window: 00004400-000044ff > [ 16.679842] IO window: 00004800-000048ff > [ 16.679849] PREFETCH window: 50000000-53ffffff > [ 16.679855] MEM window: 58000000-5bffffff > [ 16.679861] PCI: Bus 11, cardbus bridge: 0000:06:04.1 > [ 16.679865] IO window: 00004c00-00004cff > [ 16.679870] IO window: 00001400-000014ff > [ 16.679877] PREFETCH window: 54000000-57ffffff > [ 16.679884] MEM window: 5c000000-5fffffff > [ 16.679890] PCI: Bridge: 0000:00:1e.0 > [ 16.679894] IO window: 4000-4fff > [ 16.679900] MEM window: c8000000-c80fffff > [ 16.679905] PREFETCH window: 50000000-57ffffff > [ 16.679917] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, > low) -> IRQ 16 > [ 16.679924] PCI: Setting latency timer of device 0000:00:01.0 to 64 > [ 16.679939] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, > low) -> IRQ 17 > [ 16.679947] PCI: Setting latency timer of device 0000:00:1c.0 to 64 > [ 16.679957] PCI: Setting latency timer of device 0000:00:1e.0 to 64 > [ 16.679972] PCI: Enabling device 0000:06:04.0 (0000 -> 0003) > [ 16.679978] ACPI: PCI Interrupt 0000:06:04.0[A] -> GSI 22 (level, > low) -> IRQ 18 > [ 16.680000] PCI: Enabling device 0000:06:04.1 (0000 -> 0003) > [ 16.680007] ACPI: PCI Interrupt 0000:06:04.1[B] -> GSI 21 (level, > low) -> IRQ 19 > [ 16.680017] PCI: Setting latency timer of device 0000:06:04.1 to 64 > [ 16.680034] NET: Registered protocol family 2 > [ 16.689706] IP route cache hash table entries: 32768 (order: 5, 131072 > bytes) [ 16.689814] TCP established hash table entries: 131072 (order: 8, > 1048576 bytes) > [ 16.690740] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) > [ 16.691371] TCP: Hash tables configured (established 131072 bind 65536) > [ 16.691378] TCP reno registered > [ 16.693925] checking if image is initramfs... it is > [ 17.267064] Freeing initrd memory: 6366k freed > [ 17.267347] Simple Boot Flag at 0x37 set to 0x1 > [ 17.267562] audit: initializing netlink socket (disabled) > [ 17.267579] audit(1170315603.011:1): initialized > [ 17.267646] highmem bounce pool size: 64 pages > [ 17.267705] VFS: Disk quotas dquot_6.5.1 > [ 17.267726] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > [ 17.267777] io scheduler noop registered > [ 17.267781] io scheduler anticipatory registered > [ 17.267785] io scheduler deadline registered > [ 17.267796] io scheduler cfq registered (default) > [ 17.268139] PCI: Setting latency timer of device 0000:00:01.0 to 64 > [ 17.268164] assign_interrupt_mode Found MSI capability > [ 17.268195] Allocate Port Service[0000:00:01.0:pcie00] > [ 17.268224] Allocate Port Service[0000:00:01.0:pcie03] > [ 17.268278] PCI: Setting latency timer of device 0000:00:1c.0 to 64 > [ 17.268313] assign_interrupt_mode Found MSI capability > [ 17.268343] Allocate Port Service[0000:00:1c.0:pcie00] > [ 17.268370] Allocate Port Service[0000:00:1c.0:pcie02] > [ 17.268396] Allocate Port Service[0000:00:1c.0:pcie03] > [ 17.268532] isapnp: Scanning for PnP cards... > [ 17.625458] isapnp: No Plug & Play device found > [ 17.645453] Real Time Clock Driver v1.12ac > [ 17.645650] hpet_acpi_add: no address or irqs in _CRS > [ 17.645664] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, > IRQ sharing enabled > [ 17.646677] RAMDISK driver initialized: 16 RAM disks of 65536K size > 1024 blocksize > [ 17.646772] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 > [ 17.646778] ide: Assuming 33MHz system bus speed for PIO modes; > override with idebus=xx > [ 17.647034] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at > 0x60,0x64 irq 1,12 > [ 17.648931] i8042.c: Detected active multiplexing controller, rev 1.1. > [ 17.650165] serio: i8042 KBD port at 0x60,0x64 irq 1 > [ 17.650171] serio: i8042 AUX0 port at 0x60,0x64 irq 12 > [ 17.650175] serio: i8042 AUX1 port at 0x60,0x64 irq 12 > [ 17.650179] serio: i8042 AUX2 port at 0x60,0x64 irq 12 > [ 17.650183] serio: i8042 AUX3 port at 0x60,0x64 irq 12 > [ 17.650371] mice: PS/2 mouse device common for all mice > [ 17.650454] EISA: Probing bus 0 at eisa.0 > [ 17.650464] Cannot allocate resource for EISA slot 1 > [ 17.650468] Cannot allocate resource for EISA slot 2 > [ 17.650472] Cannot allocate resource for EISA slot 3 > [ 17.650475] Cannot allocate resource for EISA slot 4 > [ 17.650495] EISA: Detected 0 cards. > [ 17.680583] TCP cubic registered > [ 17.680593] NET: Registered protocol family 1 > [ 17.680600] NET: Registered protocol family 8 > [ 17.680603] NET: Registered protocol family 20 > [ 17.680665] Using IPI No-Shortcut mode > [ 17.680714] ACPI: (supports S0 S3 S4 S5) > [ 17.680911] Freeing unused kernel memory: 316k freed > [ 17.681185] Time: tsc clocksource has been installed. > [ 17.694413] input: AT Translated Set 2 keyboard as /class/input/input0 > [ 17.749894] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) > [ 17.749903] ACPI: Processor [CPU0] (supports 8 throttling states) > [ 17.749912] ACPI Exception (acpi_processor-0677): AE_NOT_FOUND, > Processor Device is not present [20060707] > [ 1.210000] Time: acpi_pm clocksource has been installed. > [ 1.274000] ACPI: Invalid passive threshold > [ 1.276000] ACPI: Thermal Zone [THM0] (50 C) > [ 1.556000] ICH6: IDE controller at PCI slot 0000:00:1f.1 > [ 1.556000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, > low) -> IRQ 20 > [ 1.556000] ICH6: chipset revision 4 > [ 1.556000] ICH6: not 100% native mode: will probe irqs later > [ 1.556000] ide0: BM-DMA at 0x1860-0x1867, BIOS settings: > hda:DMA, hdb:DMA > [ 1.556000] Probing IDE interface ide0... > [ 1.820000] hda: SAMSUNG MP0804H, ATA DISK drive > [ 2.534000] hdb: MATSHITAUJ-840D, ATAPI CD/DVD-ROM drive > [ 2.585000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > [ 2.589000] hda: max request size: 512KiB > [ 2.599000] hda: 156368016 sectors (80060 MB) w/8192KiB Cache, > CHS=16383/255/63, UDMA(100) > [ 2.599000] hda: cache flushes supported > [ 2.599000] hda: hda1 hda2 hda3 hda4 > [ 2.624000] hdb: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB > Cache, UDMA(33) > [ 2.624000] Uniform CD-ROM driver Revision: 3.20 > [ 2.936000] Probing IDE interface ide1... > [ 2.967000] usbcore: registered new interface driver usbfs > [ 2.967000] usbcore: registered new interface driver hub > [ 2.967000] usbcore: registered new device driver usb > [ 2.968000] USB Universal Host Controller Interface driver v3.0 > [ 2.968000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, > low) -> IRQ 21 > [ 2.968000] PCI: Setting latency timer of device 0000:00:1d.0 to 64 > [ 2.968000] uhci_hcd 0000:00:1d.0: UHCI Host Controller > [ 2.968000] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned > bus number 1 > [ 2.968000] uhci_hcd 0000:00:1d.0: irq 21, io base 0x00001800 > [ 2.968000] usb usb1: configuration #1 chosen from 1 choice > [ 2.968000] hub 1-0:1.0: USB hub found > [ 2.968000] hub 1-0:1.0: 2 ports detected > [ 3.016000] ieee1394: Initialized config rom entry `ip1394' > [ 3.069000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, > low) -> IRQ 22 > [ 3.069000] PCI: Setting latency timer of device 0000:00:1d.1 to 64 > [ 3.069000] uhci_hcd 0000:00:1d.1: UHCI Host Controller > [ 3.069000] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned > bus number 2 > [ 3.069000] uhci_hcd 0000:00:1d.1: irq 22, io base 0x00001820 > [ 3.069000] usb usb2: configuration #1 chosen from 1 choice > [ 3.070000] hub 2-0:1.0: USB hub found > [ 3.070000] hub 2-0:1.0: 2 ports detected > [ 3.171000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, > low) -> IRQ 20 > [ 3.171000] PCI: Setting latency timer of device 0000:00:1d.2 to 64 > [ 3.171000] uhci_hcd 0000:00:1d.2: UHCI Host Controller > [ 3.171000] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned > bus number 3 > [ 3.171000] uhci_hcd 0000:00:1d.2: irq 20, io base 0x00001840 > [ 3.171000] usb usb3: configuration #1 chosen from 1 choice > [ 3.171000] hub 3-0:1.0: USB hub found > [ 3.171000] hub 3-0:1.0: 2 ports detected > [ 3.272000] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, > low) -> IRQ 21 > [ 3.272000] PCI: Setting latency timer of device 0000:00:1d.7 to 64 > [ 3.272000] ehci_hcd 0000:00:1d.7: EHCI Host Controller > [ 3.272000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned > bus number 4 > [ 3.272000] ehci_hcd 0000:00:1d.7: debug port 1 > [ 3.272000] PCI: cache line size of 32 is not supported by device > 0000:00:1d.7 > [ 3.272000] ehci_hcd 0000:00:1d.7: irq 21, io mem 0xc0004000 > [ 3.276000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, > driver 10 Dec 2004 > [ 3.276000] usb 1-2: new low speed USB device using uhci_hcd and address > 2 [ 3.277000] usb usb4: configuration #1 chosen from 1 choice > [ 3.277000] hub 4-0:1.0: USB hub found > [ 3.277000] hub 4-0:1.0: 6 ports detected > [ 3.378000] ACPI: PCI Interrupt 0000:06:02.0[A] -> GSI 21 (level, > low) -> IRQ 19 > [ 3.437000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] > MMIO=[c8004000-c80047ff] Max Packet=[2048] IR/IT contexts=[4/8] > [ 3.706000] ReiserFS: hda4: found reiserfs format "3.6" with standard > journal [ 3.706000] ReiserFS: hda4: using ordered data mode > [ 3.718000] ReiserFS: hda4: journal params: device hda4, size 8192, > journal first block 18, max trans len 1024, max batch 900, max commit > age 30, max trans age 30 > [ 3.719000] ReiserFS: hda4: checking transaction log (hda4) > [ 3.775000] usb 1-2: new low speed USB device using uhci_hcd and address > 3 [ 3.790000] ReiserFS: hda4: Using r5 hash to sort names > [ 3.944000] usb 1-2: configuration #1 chosen from 1 choice > [ 4.693000] ieee1394: Host added: ID:BUS[0-00:1023] > GUID[0090f50000000003] [ 24.432000] input: PC Speaker as > /class/input/input1 > [ 24.483000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > [ 24.489000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 > [ 24.558000] parport: PnPBIOS parport detected. > [ 24.558000] parport0: PC-style at 0x378 (0x778), irq 7, dma 1 > [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] > [ 24.736000] Yenta: CardBus bridge found at 0000:06:04.0 [1558:04a0] > [ 24.736000] Yenta: Enabling burst memory read transactions > [ 24.736000] Yenta: Using CSCINT to route CSC interrupts to PCI > [ 24.736000] Yenta: Routing CardBus interrupts to PCI > [ 24.736000] Yenta TI: socket 0000:06:04.0, mfunc 0x00000022, devctl 0x64 > [ 24.768000] ieee80211_crypt: registered algorithm 'NULL' > [ 24.770000] ieee80211: 802.11 data/management/control stack, git-1.1.13 > [ 24.770000] ieee80211: Copyright (C) 2004-2005 Intel Corporation > <[EMAIL PROTECTED]> > [ 24.850000] irda_init() > [ 24.850000] NET: Registered protocol family 23 > [ 24.880000] Linux agpgart interface v0.101 (c) Dave Jones > [ 24.882000] agpgart: Detected an Intel 915GM Chipset. > [ 24.899000] agpgart: AGP aperture is 256M @ 0x0 > [ 24.905000] intel_rng: FWH not detected > [ 24.921000] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network > Driver, 1.2.0kmprq > [ 24.921000] ipw2200: Copyright(c) 2003-2006 Intel Corporation > [ 24.963000] Yenta: ISA IRQ mask 0x0000, PCI irq 18 > [ 24.963000] Socket status: 30000010 > [ 24.963000] Yenta: Raising subordinate bus# of parent bus (#06) > from #06 to #0a > [ 24.963000] pcmcia: parent PCI bridge I/O window: 0x4000 - 0x4fff > [ 24.963000] cs: IO port probe 0x4000-0x4fff: clean. > [ 24.964000] pcmcia: parent PCI bridge Memory window: 0xc8000000 - > 0xc80fffff [ 24.964000] pcmcia: parent PCI bridge Memory window: > 0x50000000 - 0x57ffffff [ 24.967000] Yenta: CardBus bridge found at > 0000:06:04.1 [1558:04a0] [ 24.967000] Yenta: Using CSCINT to route CSC > interrupts to PCI > [ 24.967000] Yenta: Routing CardBus interrupts to PCI > [ 24.967000] Yenta TI: socket 0000:06:04.1, mfunc 0x00000022, devctl 0x64 > [ 25.191000] Yenta: ISA IRQ mask 0x0000, PCI irq 19 > [ 25.191000] Socket status: 30000006 > [ 25.191000] Yenta: Raising subordinate bus# of parent bus (#06) > from #0a to #0e > [ 25.191000] pcmcia: parent PCI bridge I/O window: 0x4000 - 0x4fff > [ 25.191000] cs: IO port probe 0x4000-0x4fff: clean. > [ 25.191000] pcmcia: parent PCI bridge Memory window: 0xc8000000 - > 0xc80fffff [ 25.191000] pcmcia: parent PCI bridge Memory window: > 0x50000000 - 0x57ffffff [ 25.191000] ACPI: PCI Interrupt 0000:06:03.0[A] > -> GSI 20 (level, low) -> IRQ 23 > [ 25.191000] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 20 (level, > low) -> IRQ 23 > [ 25.191000] PCI: Setting latency timer of device 0000:00:1b.0 to 64 > [ 25.191000] ipw2200: Detected Intel PRO/Wireless 2915ABG Network > Connection [ 25.200000] input: ImPS/2 Logitech Wheel Mouse as > /class/input/input2 [ 25.205000] nsc_ircc_pnp_probe() : From PnP, found > firbase 0x2F8 ; irq 3 ; dma 0. > [ 25.206000] nsc-ircc, chip->init > [ 25.206000] nsc-ircc, Found chip at base=0x02e > [ 25.206000] nsc-ircc, Wrong chip version ff > [ 25.206000] nsc-ircc, Found chip at base=0x02e > [ 25.206000] nsc-ircc, Wrong chip version ff > [ 25.206000] nsc-ircc, chip->init > [ 25.206000] nsc-ircc, Found chip at base=0x02e > [ 25.206000] nsc-ircc, Wrong chip version ff > [ 25.206000] nsc-ircc, Found chip at base=0x02e > [ 25.206000] nsc-ircc, Wrong chip version ff > [ 25.206000] pnp: Device 00:08 disabled. > [ 25.238000] hda_codec: Unknown model for ALC880, trying auto-probe > from BIOS... > [ 25.552000] ipw2200: Detected geography ZZE (13 802.11bg channels, > 19 802.11a channels) > [ 25.552000] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, > low) -> IRQ 16 > [ 25.552000] PCI: Setting latency timer of device 0000:02:00.0 to 64 > [ 25.552000] sky2 v1.10 addr 0xc4000000 irq 16 Yukon-EC (0xb6) rev 2 > [ 25.553000] sky2 eth1: addr 00:90:f5:46:cd:0f > [ 25.576000] usbcore: registered new interface driver hiddev > [ 25.650000] pccard: PCMCIA card inserted into slot 0 > [ 25.666000] input: Microsoft Microsoft 3-Button Mouse with > IntelliEye(TM) as /class/input/input3 > [ 25.666000] input: USB HID v1.10 Mouse [Microsoft Microsoft > 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:1d.0-2 > [ 25.666000] usbcore: registered new interface driver usbhid > [ 25.666000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver > [ 25.804000] cs: memory probe 0xc8000000-0xc80fffff: excluding > 0xc8000000-0xc800ffff > [ 25.819000] pcmcia: registering new device pcmcia0.0 > [ 25.924000] orinoco 0.15 (David Gibson > <[EMAIL PROTECTED]>, Pavel Roskin <[EMAIL PROTECTED]>, et al) > [ 26.119000] cs: IO port probe 0x100-0x4ff: excluding 0x3c0-0x3df > 0x4d0-0x4d7 [ 26.121000] cs: IO port probe 0xc00-0xcf7: clean. > [ 26.122000] cs: IO port probe 0xa00-0xaff: clean. > [ 26.127000] cs: IO port probe 0x100-0x4ff: excluding 0x3c0-0x3df > 0x4d0-0x4d7 [ 26.130000] cs: IO port probe 0xc00-0xcf7: clean. > [ 26.130000] cs: IO port probe 0xa00-0xaff: clean. > [ 26.156000] orinoco_cs 0.15 (David Gibson > <[EMAIL PROTECTED]>, Pavel Roskin <[EMAIL PROTECTED]>, et al) > [ 26.156000] pcmcia: request for exclusive IRQ could not be fulfilled. > [ 26.156000] pcmcia: the driver needs updating to supported shared IRQ > lines. [ 26.343000] eth1: Hardware identity 8000:0001:0000:0000 > [ 26.343000] eth1: Station identity 001f:0002:0002:0001 > [ 26.344000] eth1: Firmware determined as Symbol V2.51-04 > [ 26.344000] eth1: Ad-hoc demo mode supported > [ 26.344000] eth1: IEEE standard IBSS ad-hoc mode supported > [ 26.344000] eth1: WEP supported, 104-bit key > [ 26.344000] eth1: MAC address 00:02:B3:04:7B:F6 > [ 26.344000] eth1: Station name "Prism I" > [ 26.344000] eth1: ready > [ 26.346000] eth1: orinoco_cs at 0.0, irq 18, io 0x4080-0x40c7 > [ 26.569000] lp0: using parport0 (interrupt-driven). > [ 26.742000] SCSI subsystem initialized > [ 26.988000] Adding 1461904k swap on > /dev/disk/by-uuid/9bf56c5a-2881-4820-879b-9b6db2644a31. Priority:-1 > extents:1 across:1461904k > [ 38.651000] ip_tables: (C) 2000-2006 Netfilter Core Team > [ 39.799000] PPP generic driver version 2.4.2 > [ 39.820000] NET: Registered protocol family 17 > [ 40.768000] Using specific hotkey driver > [ 40.828000] ACPI: AC Adapter [ADP0] (on-line) > [ 40.838000] No dock devices found. > [ 40.872000] toshiba_acpi: Unknown parameter `hotkeys_over_acpi' > [ 40.916000] input: Power Button (FF) as /class/input/input4 > [ 40.927000] ACPI: Power Button (FF) [PWRF] > [ 40.963000] input: Power Button (CM) as /class/input/input5 > [ 40.973000] ACPI: Power Button (CM) [PWRB] > [ 41.002000] input: Lid Switch as /class/input/input6 > [ 41.002000] ACPI: Lid Switch [LID0] > [ 41.018000] input: Sleep Button (CM) as /class/input/input7 > [ 41.018000] ACPI: Sleep Button (CM) [SLPB] > [ 41.096000] ibm_acpi: ec object not found > [ 41.111000] ACPI: Battery Slot [BAT0] (battery present) > [ 41.120000] ACPI: Video Device [VGA] (multi-head: yes rom: no post: > no) [ 41.286000] speedstep-centrino with X86_SPEEDSTEP_CENTRINO_ACPI > config is deprecated. > [ 41.286000] Use X86_ACPI_CPUFREQ (acpi-cpufreq) instead. > [ 44.728000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) > [ 44.728000] apm: overridden by ACPI. > [ 48.985000] mtrr: no more MTRRs available > [ 48.985000] mtrr: no more MTRRs available > [ 48.985000] mtrr: no more MTRRs available > [ 48.985000] mtrr: no more MTRRs available > [ 216.408000] usb 4-3: new high speed USB device using ehci_hcd and > address 3 [ 216.537000] usb 4-3: configuration #1 chosen from 1 choice > [ 216.650000] usbcore: registered new interface driver libusual > [ 216.664000] Initializing USB Mass Storage driver... > [ 216.664000] scsi0 : SCSI emulation for USB Mass Storage devices > [ 216.664000] usbcore: registered new interface driver usb-storage > [ 216.664000] USB Mass Storage support registered. > [ 216.664000] usb-storage: device found at 3 > [ 216.664000] usb-storage: waiting for device to settle before scanning > [ 221.668000] scsi 0:0:0:0: Direct-Access GENERIC USB > Storage-SMC I16A PQ: 0 ANSI: 0 CCS > [ 221.673000] scsi 0:0:0:1: Direct-Access GENERIC USB > Storage-CFC I16A PQ: 0 ANSI: 0 CCS > [ 221.678000] scsi 0:0:0:2: Direct-Access GENERIC USB > Storage-SDC I16A PQ: 0 ANSI: 0 CCS > [ 221.683000] scsi 0:0:0:3: Direct-Access GENERIC USB > Storage-MSC I16A PQ: 0 ANSI: 0 CCS > [ 221.691000] usb-storage: device scan complete > [ 221.792000] sd 0:0:0:0: Attached scsi removable disk sda > [ 221.794000] sd 0:0:0:1: Attached scsi removable disk sdb > [ 221.798000] SCSI device sdc: 1992704 512-byte hdwr sectors (1020 MB) > [ 221.812000] sdc: Write Protect is off > [ 221.812000] sdc: Mode Sense: 00 00 00 00 > [ 221.812000] sdc: assuming drive cache: write through > [ 221.837000] SCSI device sdc: 1992704 512-byte hdwr sectors (1020 MB) > [ 221.849000] sdc: Write Protect is off > [ 221.849000] sdc: Mode Sense: 00 00 00 00 > [ 221.849000] sdc: assuming drive cache: write through > [ 221.849000] sdc: sdc1 > [ 221.851000] sdc: p1 exceeds device capacity > [ 221.852000] sd 0:0:0:2: Attached scsi removable disk sdc > [ 221.854000] sd 0:0:0:3: Attached scsi removable disk sdd > [ 221.878000] sd 0:0:0:0: Attached scsi generic sg0 type 0 > [ 221.879000] sd 0:0:0:1: Attached scsi generic sg1 type 0 > [ 221.879000] sd 0:0:0:2: Attached scsi generic sg2 type 0 > [ 221.879000] sd 0:0:0:3: Attached scsi generic sg3 type 0 > [ 222.030000] attempt to access beyond end of device > [ 222.030000] sdc: rw=0, want=3985272, limit=1992704 > [ 222.030000] Buffer I/O error on device sdc1, logical block 3985024 > [ 222.031000] attempt to access beyond end of device > [ 222.031000] sdc: rw=0, want=3985273, limit=1992704 > [ 222.031000] Buffer I/O error on device sdc1, logical block 3985025 > [ 222.031000] attempt to access beyond end of device > [ 222.031000] sdc: rw=0, want=3985274, limit=1992704 > [ 222.031000] Buffer I/O error on device sdc1, logical block 3985026 > [ 222.031000] attempt to access beyond end of device > [ 222.031000] sdc: rw=0, want=3985275, limit=1992704 > [ 222.031000] Buffer I/O error on device sdc1, logical block 3985027 > [ 222.032000] attempt to access beyond end of device > [ 222.032000] sdc: rw=0, want=3985276, limit=1992704 > [ 222.032000] Buffer I/O error on device sdc1, logical block 3985028 > [ 222.032000] attempt to access beyond end of device > [ 222.032000] sdc: rw=0, want=3985277, limit=1992704 > [ 222.032000] Buffer I/O error on device sdc1, logical block 3985029 > [ 222.033000] attempt to access beyond end of device > [ 222.033000] sdc: rw=0, want=3985278, limit=1992704 > [ 222.033000] Buffer I/O error on device sdc1, logical block 3985030 > [ 222.033000] attempt to access beyond end of device > [ 222.033000] sdc: rw=0, want=3985279, limit=1992704 > [ 222.033000] Buffer I/O error on device sdc1, logical block 3985031 > [ 222.034000] attempt to access beyond end of device > [ 222.034000] sdc: rw=0, want=3985272, limit=1992704 > [ 222.034000] Buffer I/O error on device sdc1, logical block 3985024 > [ 222.034000] attempt to access beyond end of device > [ 222.034000] sdc: rw=0, want=3985273, limit=1992704 > [ 222.034000] Buffer I/O error on device sdc1, logical block 3985025 > [ 222.035000] attempt to access beyond end of device > [ 222.035000] sdc: rw=0, want=3985274, limit=1992704 > [ 222.035000] attempt to access beyond end of device > [ 222.035000] sdc: rw=0, want=3985275, limit=1992704 > [ 222.035000] attempt to access beyond end of device > [ 222.035000] sdc: rw=0, want=3985276, limit=1992704 > [ 222.036000] attempt to access beyond end of device > [ 222.036000] sdc: rw=0, want=3985277, limit=1992704 > [ 222.036000] attempt to access beyond end of device > [ 222.036000] sdc: rw=0, want=3985278, limit=1992704 > [ 222.036000] attempt to access beyond end of device > [ 222.036000] sdc: rw=0, want=3985279, limit=1992704 > [ 222.037000] attempt to access beyond end of device > [ 222.037000] sdc: rw=0, want=3985400, limit=1992704 > [ 222.037000] attempt to access beyond end of device > [ 222.037000] sdc: rw=0, want=3985401, limit=1992704 > [ 222.037000] attempt to access beyond end of device > [ 222.037000] sdc: rw=0, want=3985402, limit=1992704 > [ 222.037000] attempt to access beyond end of device > [ 222.037000] sdc: rw=0, want=3985403, limit=1992704 > [ 222.038000] attempt to access beyond end of device > [ 222.038000] sdc: rw=0, want=3985404, limit=1992704 > [ 222.038000] attempt to access beyond end of device > [ 222.038000] sdc: rw=0, want=3985405, limit=1992704 > [ 222.038000] attempt to access beyond end of device > [ 222.038000] sdc: rw=0, want=3985406, limit=1992704 > [ 222.039000] attempt to access beyond end of device > [ 222.039000] sdc: rw=0, want=3985407, limit=1992704 > [ 222.039000] attempt to access beyond end of device > [ 222.039000] sdc: rw=0, want=3985400, limit=1992704 > [ 222.039000] attempt to access beyond end of device > [ 222.039000] sdc: rw=0, want=3985401, limit=1992704 > [ 222.040000] attempt to access beyond end of device > [ 222.040000] sdc: rw=0, want=3985402, limit=1992704 > [ 222.040000] attempt to access beyond end of device > [ 222.040000] sdc: rw=0, want=3985403, limit=1992704 > [ 222.040000] attempt to access beyond end of device > [ 222.040000] sdc: rw=0, want=3985404, limit=1992704 > [ 222.040000] attempt to access beyond end of device > [ 222.040000] sdc: rw=0, want=3985405, limit=1992704 > [ 222.041000] attempt to access beyond end of device > [ 222.041000] sdc: rw=0, want=3985406, limit=1992704 > [ 222.041000] attempt to access beyond end of device > [ 222.041000] sdc: rw=0, want=3985407, limit=1992704 > [ 222.041000] attempt to access beyond end of device > [ 222.041000] sdc: rw=0, want=3985408, limit=1992704 > [ 222.042000] attempt to access beyond end of device > [ 222.042000] sdc: rw=0, want=3985408, limit=1992704 > [ 222.042000] attempt to access beyond end of device > [ 222.042000] sdc: rw=0, want=3985408, limit=1992704 > [ 222.042000] attempt to access beyond end of device > [ 222.042000] sdc: rw=0, want=3985408, limit=1992704 > [ 222.043000] attempt to access beyond end of device > [ 222.043000] sdc: rw=0, want=3985400, limit=1992704 > [ 222.043000] attempt to access beyond end of device > [ 222.043000] sdc: rw=0, want=3985401, limit=1992704 > [ 222.043000] attempt to access beyond end of device > [ 222.043000] sdc: rw=0, want=3985402, limit=1992704 > [ 222.044000] attempt to access beyond end of device > [ 222.044000] sdc: rw=0, want=3985403, limit=1992704 > [ 222.044000] attempt to access beyond end of device > [ 222.044000] sdc: rw=0, want=3985404, limit=1992704 > [ 222.044000] attempt to access beyond end of device > [ 222.044000] sdc: rw=0, want=3985405, limit=1992704 > [ 222.044000] attempt to access beyond end of device > [ 222.044000] sdc: rw=0, want=3985406, limit=1992704 > [ 222.045000] attempt to access beyond end of device > [ 222.045000] sdc: rw=0, want=3985407, limit=1992704 > [ 222.045000] attempt to access beyond end of device > [ 222.045000] sdc: rw=0, want=3985344, limit=1992704 > [ 222.045000] attempt to access beyond end of device > [ 222.045000] sdc: rw=0, want=3985345, limit=1992704 > [ 222.046000] attempt to access beyond end of device > [ 222.046000] sdc: rw=0, want=3985346, limit=1992704 > [ 222.046000] attempt to access beyond end of device > [ 222.046000] sdc: rw=0, want=3985347, limit=1992704 > [ 222.046000] attempt to access beyond end of device > [ 222.046000] sdc: rw=0, want=3985348, limit=1992704 > [ 222.047000] attempt to access beyond end of device > [ 222.047000] sdc: rw=0, want=3985349, limit=1992704 > [ 222.047000] attempt to access beyond end of device > [ 222.047000] sdc: rw=0, want=3985350, limit=1992704 > [ 222.047000] attempt to access beyond end of device > [ 222.047000] sdc: rw=0, want=3985351, limit=1992704 > [ 222.048000] attempt to access beyond end of device > [ 222.048000] sdc: rw=0, want=3985392, limit=1992704 > [ 222.048000] attempt to access beyond end of device > [ 222.048000] sdc: rw=0, want=3985393, limit=1992704 > [ 222.048000] attempt to access beyond end of device > [ 222.048000] sdc: rw=0, want=3985394, limit=1992704 > [ 222.049000] attempt to access beyond end of device > [ 222.049000] sdc: rw=0, want=3985395, limit=1992704 > [ 222.049000] attempt to access beyond end of device > [ 222.049000] sdc: rw=0, want=3985396, limit=1992704 > [ 222.049000] attempt to access beyond end of device > [ 222.049000] sdc: rw=0, want=3985397, limit=1992704 > [ 222.050000] attempt to access beyond end of device > [ 222.050000] sdc: rw=0, want=3985398, limit=1992704 > [ 222.050000] attempt to access beyond end of device > [ 222.050000] sdc: rw=0, want=3985399, limit=1992704 > [ 222.050000] attempt to access beyond end of device > [ 222.050000] sdc: rw=0, want=3985408, limit=1992704 > [ 222.050000] attempt to access beyond end of device > [ 222.050000] sdc: rw=0, want=3985408, limit=1992704 > [ 222.108000] attempt to access beyond end of device > [ 222.108000] sdc: rw=0, want=3985272, limit=1992704 > [ 222.109000] attempt to access beyond end of device > [ 222.109000] sdc: rw=0, want=3985273, limit=1992704 > [ 222.109000] attempt to access beyond end of device > [ 222.109000] sdc: rw=0, want=3985274, limit=1992704 > [ 222.109000] attempt to access beyond end of device > [ 222.109000] sdc: rw=0, want=3985275, limit=1992704 > [ 222.110000] attempt to access beyond end of device > [ 222.110000] sdc: rw=0, want=3985276, limit=1992704 > [ 222.110000] attempt to access beyond end of device > [ 222.110000] sdc: rw=0, want=3985277, limit=1992704 > [ 222.110000] attempt to access beyond end of device > [ 222.110000] sdc: rw=0, want=3985278, limit=1992704 > [ 222.111000] attempt to access beyond end of device > [ 222.111000] sdc: rw=0, want=3985279, limit=1992704 > [ 222.111000] attempt to access beyond end of device > [ 222.111000] sdc: rw=0, want=3985272, limit=1992704 > [ 222.111000] attempt to access beyond end of device > [ 222.111000] sdc: rw=0, want=3985273, limit=1992704 > [ 222.112000] attempt to access beyond end of device > [ 222.112000] sdc: rw=0, want=3985274, limit=1992704 > [ 222.112000] attempt to access beyond end of device > [ 222.112000] sdc: rw=0, want=3985275, limit=1992704 > [ 222.112000] attempt to access beyond end of device > [ 222.112000] sdc: rw=0, want=3985276, limit=1992704 > [ 222.113000] attempt to access beyond end of device > [ 222.113000] sdc: rw=0, want=3985277, limit=1992704 > [ 222.113000] attempt to access beyond end of device > [ 222.113000] sdc: rw=0, want=3985278, limit=1992704 > [ 222.113000] attempt to access beyond end of device > [ 222.113000] sdc: rw=0, want=3985279, limit=1992704 > [ 222.114000] attempt to access beyond end of device > [ 222.114000] sdc: rw=0, want=3985400, limit=1992704 > [ 222.114000] attempt to access beyond end of device > [ 222.114000] sdc: rw=0, want=3985401, limit=1992704 > [ 222.114000] attempt to access beyond end of device > [ 222.114000] sdc: rw=0, want=3985402, limit=1992704 > [ 222.114000] attempt to access beyond end of device > [ 222.114000] sdc: rw=0, want=3985403, limit=1992704 > [ 222.115000] attempt to access beyond end of device > [ 222.115000] sdc: rw=0, want=3985404, limit=1992704 > [ 222.115000] attempt to access beyond end of device > [ 222.115000] sdc: rw=0, want=3985405, limit=1992704 > [ 222.115000] attempt to access beyond end of device > [ 222.115000] sdc: rw=0, want=3985406, limit=1992704 > [ 222.116000] attempt to access beyond end of device > [ 222.116000] sdc: rw=0, want=3985407, limit=1992704 > [ 222.116000] attempt to access beyond end of device > [ 222.116000] sdc: rw=0, want=3985400, limit=1992704 > [ 222.116000] attempt to access beyond end of device > [ 222.116000] sdc: rw=0, want=3985401, limit=1992704 > [ 222.117000] attempt to access beyond end of device > [ 222.117000] sdc: rw=0, want=3985402, limit=1992704 > [ 222.117000] attempt to access beyond end of device > [ 222.117000] sdc: rw=0, want=3985403, limit=1992704 > [ 222.117000] attempt to access beyond end of device > [ 222.117000] sdc: rw=0, want=3985404, limit=1992704 > [ 222.117000] attempt to access beyond end of device > [ 222.117000] sdc: rw=0, want=3985405, limit=1992704 > [ 222.118000] attempt to access beyond end of device > [ 222.118000] sdc: rw=0, want=3985406, limit=1992704 > [ 222.118000] attempt to access beyond end of device > [ 222.118000] sdc: rw=0, want=3985407, limit=1992704 > [ 222.118000] attempt to access beyond end of device > [ 222.118000] sdc: rw=0, want=3985408, limit=1992704 > [ 222.119000] attempt to access beyond end of device > [ 222.119000] sdc: rw=0, want=3985408, limit=1992704 > [ 222.119000] attempt to access beyond end of device > [ 222.119000] sdc: rw=0, want=3985408, limit=1992704 > [ 222.119000] attempt to access beyond end of device > [ 222.119000] sdc: rw=0, want=3985408, limit=1992704 > [ 222.120000] attempt to access beyond end of device > [ 222.120000] sdc: rw=0, want=3985400, limit=1992704 > [ 222.120000] attempt to access beyond end of device > [ 222.120000] sdc: rw=0, want=3985401, limit=1992704 > [ 222.120000] attempt to access beyond end of device > [ 222.120000] sdc: rw=0, want=3985402, limit=1992704 > [ 222.121000] attempt to access beyond end of device > [ 222.121000] sdc: rw=0, want=3985403, limit=1992704 > [ 222.121000] attempt to access beyond end of device > [ 222.121000] sdc: rw=0, want=3985404, limit=1992704 > [ 222.121000] attempt to access beyond end of device > [ 222.121000] sdc: rw=0, want=3985405, limit=1992704 > [ 222.121000] attempt to access beyond end of device > [ 222.121000] sdc: rw=0, want=3985406, limit=1992704 > [ 222.122000] attempt to access beyond end of device > [ 222.122000] sdc: rw=0, want=3985407, limit=1992704 > [ 222.122000] attempt to access beyond end of device > [ 222.122000] sdc: rw=0, want=3985344, limit=1992704 > [ 222.122000] attempt to access beyond end of device > [ 222.122000] sdc: rw=0, want=3985345, limit=1992704 > [ 222.123000] attempt to access beyond end of device > [ 222.123000] sdc: rw=0, want=3985346, limit=1992704 > [ 222.123000] attempt to access beyond end of device > [ 222.123000] sdc: rw=0, want=3985347, limit=1992704 > [ 222.123000] attempt to access beyond end of device > [ 222.123000] sdc: rw=0, want=3985348, limit=1992704 > [ 222.124000] attempt to access beyond end of device > [ 222.124000] sdc: rw=0, want=3985349, limit=1992704 > [ 222.124000] attempt to access beyond end of device > [ 222.124000] sdc: rw=0, want=3985350, limit=1992704 > [ 222.124000] attempt to access beyond end of device > [ 222.124000] sdc: rw=0, want=3985351, limit=1992704 > [ 222.124000] attempt to access beyond end of device > [ 222.124000] sdc: rw=0, want=3985392, limit=1992704 > [ 222.125000] attempt to access beyond end of device > [ 222.125000] sdc: rw=0, want=3985393, limit=1992704 > [ 222.125000] attempt to access beyond end of device > [ 222.125000] sdc: rw=0, want=3985394, limit=1992704 > [ 222.125000] attempt to access beyond end of device > [ 222.125000] sdc: rw=0, want=3985395, limit=1992704 > [ 222.126000] attempt to access beyond end of device > [ 222.126000] sdc: rw=0, want=3985396, limit=1992704 > [ 222.126000] attempt to access beyond end of device > [ 222.126000] sdc: rw=0, want=3985397, limit=1992704 > [ 222.126000] attempt to access beyond end of device > [ 222.126000] sdc: rw=0, want=3985398, limit=1992704 > [ 222.127000] attempt to access beyond end of device > [ 222.127000] sdc: rw=0, want=3985399, limit=1992704 > [ 222.410000] FAT: utf8 is not a recommended IO charset for FAT > filesystems, filesystem will be case sensitive! > [ 224.046000] FAT: Filesystem panic (dev sdc1) > [ 224.046000] fat_get_cluster: invalid cluster chain (i_pos 0) > [ 224.046000] File system has been set read-only > [ 224.048000] FAT: Filesystem panic (dev sdc1) > [ 224.048000] fat_get_cluster: invalid cluster chain (i_pos 0) > [ 224.049000] FAT: Filesystem panic (dev sdc1) > > Under Windows (XP or Windows Mobile 2005 (PDA) i see 2GB capacity, > works correctly. > > Please ask for more info. > > Thank you! > > -- > kobi > - > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > the body of a message to [EMAIL PROTECTED] > More majordomo info at http://vger.kernel.org/majordomo-info.html > Please read the FAQ at http://www.tux.org/lkml/ > > ------------------------------------------------------------------------- > Using Tomcat but need to do more? Need to support web services, security? > Get stuff done quickly with pre-integrated technology to make your job > easier. Download IBM WebSphere Application Server v.1.0.1 based on Apache > Geronimo > http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642 > _______________________________________________ > [email protected] > To unsubscribe, use the last form field at: > https://lists.sourceforge.net/lists/listinfo/linux-usb-devel ------------------------------------------------------------------------- Using Tomcat but need to do more? Need to support web services, security? Get stuff done quickly with pre-integrated technology to make your job easier. Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642 _______________________________________________ [email protected] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
