Applied the patch. It looks like we took a step back. The latest dmesg,
lsusb, and usbdevices files are attached. I thought you might want to see
them before I comment out the "goto fail_and_release" statement. Just let
me know if you want to see the results of that change.
Thanks again,
Mark
On Thu, Apr 19, 2007 at 11:51:24AM -0700, David Brownell wrote:
> On Thursday 19 April 2007 10:48 am, David Brownell wrote:
>
> > But after Oliver's hack, there was still:
> >
> > > rndis_host 3-1:1.0: dev can't take 1558 byte packets (max 0)
> >
> > And that means something else: the device took the RNDIS
> > initialization request, but didn't return a sane response.
> > So it's acting as if it's not actually an RNDIS device...
> >
> >
> > And then for some reason it didn't clean up correctly
> > after reporting the error above ...
>
> Whoops, I missed the obvious reason for that. See the
> updated patch, appended. Given this patch, it should
> act more sanely ... at least in the sense that all the
> fault modes around the edges behave right.
>
> To try working around the error above, try just
> commenting out the "goto fail_and_release" statement
> next to the rndis_host.c line this patch adds ...
> there's no guarantee it'll work though.
>
> It can be quite surprising just how broken devices can
> be when their vendors only claim MS-Windows "support"...
>
> - Dave
VD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
PCI: Found IRQ 10 for device 0000:01:04.0
PCI: Sharing IRQ 10 with 0000:00:1d.2
PCI: Sharing IRQ 10 with 0000:00:1f.1
sym0: <875> rev 0x4 at pci 0000:01:04.0 irq 10
sym0: Symbios NVRAM, ID 7, Fast-20, SE, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.2.3
scsi 0:0:6:0: Direct-Access IOMEGA ZIP 250 H.41 PQ: 0 ANSI: 2
target0:0:6: Beginning Domain Validation
scsi 0:0:6:0: phase change 6-7 [EMAIL PROTECTED] resid=4.
target0:0:6: asynchronous
target0:0:6: Ending Domain Validation
sd 0:0:6:0: Attached scsi removable disk sda
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
PCI: Found IRQ 9 for device 0000:00:1d.7
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1 cc=4 pcc=2 ordered !ppc
ports=8
ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: supports USB remote wakeup
ehci_hcd 0000:00:1d.7: irq 9, io mem 0xffa7fc00
ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024
Reset HALT
ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.21-rc7 ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: trying to enable port power on non-switchable hub
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0000
drivers/usb/core/inode.c: creating file '001'
USB Universal Host Controller Interface driver v3.0
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
PCI: Found IRQ 11 for device 0000:00:1d.0
PCI: Sharing IRQ 11 with 0000:00:02.0
PCI: Sharing IRQ 11 with 0000:00:1d.3
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
drivers/usb/core/inode.c: creating file '002'
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: detected 2 ports
uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:1d.0: Performing full reset
uhci_hcd 0000:00:1d.0: irq 11, io base 0x0000dc00
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.21-rc7 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
usb usb2: uevent
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: trying to enable port power on non-switchable hub
drivers/usb/core/inode.c: creating file '001'
PCI: Found IRQ 5 for device 0000:00:1d.1
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
drivers/usb/core/inode.c: creating file '003'
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: detected 2 ports
uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:1d.1: Performing full reset
uhci_hcd 0000:00:1d.1: irq 5, io base 0x0000e000
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.21-rc7 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1
usb usb3: uevent
usb usb3: usb_probe_device
usb usb3: configuration #1 chosen from 1 choice
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: uevent
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
hub 3-0:1.0: trying to enable port power on non-switchable hub
hub 1-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:1d.7: port 3 full speed --> companion
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 003801 POWER OWNER sig=j CONNECT
hub 1-0:1.0: port 3 not reset yet, waiting 50ms
drivers/usb/core/inode.c: creating file '001'
PCI: Found IRQ 10 for device 0000:00:1d.2
PCI: Sharing IRQ 10 with 0000:00:1f.1
PCI: Sharing IRQ 10 with 0000:01:04.0
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
drivers/usb/core/inode.c: creating file '004'
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: detected 2 ports
uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:1d.2: Performing full reset
uhci_hcd 0000:00:1d.2: irq 10, io base 0x0000e400
usb usb4: default language 0x0409
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.21-rc7 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2
usb usb4: uevent
usb usb4: usb_probe_device
usb usb4: configuration #1 chosen from 1 choice
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: uevent
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
hub 4-0:1.0: trying to enable port power on non-switchable hub
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 003002 POWER OWNER sig=se0 CSC
hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0008
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0002
uhci_hcd 0000:00:1d.1: port 1 portsc 0093,00
hub 3-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
drivers/usb/core/inode.c: creating file '001'
PCI: Found IRQ 11 for device 0000:00:1d.3
PCI: Sharing IRQ 11 with 0000:00:02.0
PCI: Sharing IRQ 11 with 0000:00:1d.0
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
drivers/usb/core/inode.c: creating file '005'
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: detected 2 ports
uhci_hcd 0000:00:1d.3: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:1d.3: Performing full reset
uhci_hcd 0000:00:1d.3: irq 11, io base 0x0000e800
usb usb5: default language 0x0409
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.21-rc7 uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.3
usb usb5: uevent
usb usb5: usb_probe_device
usb usb5: configuration #1 chosen from 1 choice
usb usb5: adding 5-0:1.0 (config #1, interface 0)
usb 5-0:1.0: uevent
hub 5-0:1.0: usb_probe_interface
hub 5-0:1.0: usb_probe_interface - got id
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
hub 5-0:1.0: standalone hub
hub 5-0:1.0: no power switching (usb 1.0)
hub 5-0:1.0: individual port over-current protection
hub 5-0:1.0: power on to power good time: 2ms
hub 5-0:1.0: local power source is good
hub 5-0:1.0: trying to enable port power on non-switchable hub
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
drivers/usb/core/inode.c: creating file '001'
usb 3-1: new full speed USB device using uhci_hcd and address 2
usb 3-1: ep0 maxpacket = 8
usb 3-1: skipped 4 descriptors after endpoint
usb 3-1: default language 0x0409
usb 3-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-1: Product: 2Wire USB Remote NDIS Ethernet
usb 3-1: Manufacturer: 2Wire Inc
usb 3-1: uevent
usb 3-1: usb_probe_device
usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: adding 3-1:1.0 (config #1, interface 0)
usb 3-1:1.0: uevent
usb 3-1: adding 3-1:1.1 (config #1, interface 1)
usb 3-1:1.1: uevent
drivers/usb/core/inode.c: creating file '002'
hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
usbcore: registered new interface driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB
modems and ISDN adapters
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
usbcore: registered new interface driver cdc_ether
rndis_host 3-1:1.0: usb_probe_interface
rndis_host 3-1:1.0: usb_probe_interface - got id
rndis_host 3-1:1.0: CDC descriptors on endpoint
usbdev3.2_ep82: ep_device_release called for usbdev3.2_ep82
usbdev3.2_ep03: ep_device_release called for usbdev3.2_ep03
usb usb2: suspend_rh (auto-stop)
usb usb4: suspend_rh (auto-stop)
usb usb5: suspend_rh (auto-stop)
usb 3-1: swapper timed out on ep0in len=0/1025
rndis_host 3-1:1.0: rndis response error, code -110
usb 3-1: swapper timed out on ep0in len=0/1025
rndis_host 3-1:1.0: rndis response error, code -110
usb 3-1: swapper timed out on ep0in len=0/1025
rndis_host 3-1:1.0: rndis response error, code -110
usb 3-1: swapper timed out on ep0in len=0/1025
rndis_host 3-1:1.0: rndis response error, code -110
usb 3-1: swapper timed out on ep0in len=0/1025
rndis_host 3-1:1.0: rndis response error, code -110
usb 3-1: swapper timed out on ep0in len=0/1025
rndis_host 3-1:1.0: rndis response error, code -110
usb 3-1: swapper timed out on ep0in len=0/1025
rndis_host 3-1:1.0: rndis response error, code -110
usb 3-1: swapper timed out on ep0in len=0/1025
rndis_host 3-1:1.0: rndis response error, code -110
usb 3-1: swapper timed out on ep0in len=0/1025
rndis_host 3-1:1.0: rndis response error, code -110
usb 3-1: swapper timed out on ep0in len=0/1025
rndis_host 3-1:1.0: rndis response error, code -110
rndis_host 3-1:1.0: rndis response timeout
rndis_host 3-1:1.0: RNDIS init failed, -110
usbdev3.2_ep82: ep_device_release called for usbdev3.2_ep82
usbdev3.2_ep03: ep_device_release called for usbdev3.2_ep03
rndis_host: probe of 3-1:1.0 failed with error -110
usbcore: registered new interface driver rndis_host
usbcore: registered new interface driver ldusb
drivers/usb/atm/usbatm.c: usbatm_usb_init: driver version 1.10
drivers/usb/atm/xusbatm.c: xusbatm_init
drivers/usb/atm/xusbatm.c: malformed module parameters
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
input: PC Speaker as /class/input/input1
logips2pp: Detected unknown logitech mouse model 1
input: PS/2 Logitech Mouse as /class/input/input2
PCI: Found IRQ 3 for device 0000:00:1f.3
PCI: Sharing IRQ 3 with 0000:00:1f.5
PCI: Sharing IRQ 3 with 0000:01:05.0
Advanced Linux Sound Architecture Driver Version 1.0.14rc3 (Wed Mar 14 07:25:50
2007 UTC).
PCI: Found IRQ 3 for device 0000:00:1f.5
PCI: Sharing IRQ 3 with 0000:00:1f.3
PCI: Sharing IRQ 3 with 0000:01:05.0
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 55268 usecs
intel8x0: clocking to 48000
ALSA device list:
#0: Intel ICH5 with AD1985 at irq 3
Netfilter messages via NETLINK v0.30.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
Using IPI Shortcut mode
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 160k freed
Adding 249440k swap on /dev/hdb6. Priority:-1 extents:1 across:249440k
eth1: link down
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0002
uhci_hcd 0000:00:1d.1: port 1 portsc 008a,00
hub 3-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
usb 3-1: USB disconnect, address 2
usb 3-1: unregistering device
usb 3-1: usb_disable_device nuking all URBs
usb 3-1: unregistering interface 3-1:1.0
usbdev3.2_ep81: ep_device_release called for usbdev3.2_ep81
usb 3-1:1.0: uevent
usb 3-1: unregistering interface 3-1:1.1
usbdev3.2_ep82: ep_device_release called for usbdev3.2_ep82
usbdev3.2_ep03: ep_device_release called for usbdev3.2_ep03
usb 3-1:1.1: uevent
usbdev3.2_ep00: ep_device_release called for usbdev3.2_ep00
usb 3-1: uevent
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
usb usb3: suspend_rh (auto-stop)
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0008
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:1d.7: port 3 full speed --> companion
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 003801 POWER OWNER sig=j CONNECT
hub 1-0:1.0: port 3 not reset yet, waiting 50ms
usb usb3: wakeup_rh (auto-start)
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 003002 POWER OWNER sig=se0 CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0008
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0002
uhci_hcd 0000:00:1d.1: port 1 portsc 0093,00
hub 3-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
usb 3-1: new full speed USB device using uhci_hcd and address 3
usb 3-1: ep0 maxpacket = 8
usb 3-1: skipped 4 descriptors after endpoint
usb 3-1: default language 0x0409
usb 3-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-1: Product: 2Wire USB Remote NDIS Ethernet
usb 3-1: Manufacturer: 2Wire Inc
usb 3-1: uevent
usb 3-1: usb_probe_device
usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: adding 3-1:1.0 (config #1, interface 0)
usb 3-1:1.0: uevent
rndis_host 3-1:1.0: usb_probe_interface
rndis_host 3-1:1.0: usb_probe_interface - got id
rndis_host 3-1:1.0: CDC descriptors on endpoint
rndis_host 3-1:1.0: dev can't take 1558 byte packets (max 0)
rndis_host: probe of 3-1:1.0 failed with error -22
usb 3-1: adding 3-1:1.1 (config #1, interface 1)
usb 3-1:1.1: uevent
drivers/usb/core/inode.c: creating file '003'
Device: ID 1630:0042
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.01
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x1630
idProduct 0x0042
bcdDevice 1.00
iManufacturer 1 2Wire Inc
iProduct 2 2Wire USB Remote NDIS Ethernet
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 67
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 4 2WIREHPL
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 40mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 255 Vendor Specific (MSFT RNDIS?)
iInterface 5 ndis5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 1
CDC Header:
bcdCDC 1.00
CDC Call Management:
bmCapabilities 0x00
bDataInterface 1
CDC ACM:
bmCapabilities 0x00
CDC Union:
bMasterInterface 0
bSlaveInterface 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 6 ethernet
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Status: 0x0001
Self Powered
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.21-rc7 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:1d.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.01 Cls=02(comm.) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=1630 ProdID=0042 Rev= 1.00
S: Manufacturer=2Wire Inc
S: Product=2Wire USB Remote NDIS Ethernet
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr= 40mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=02 Prot=ff Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=1ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=(none)
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
-------------------------------------------------------------------------
This SF.net email is sponsored by DB2 Express
Download DB2 Express C - the FREE version of DB2 express and take
control of your XML. No limits. Just data. Click to get it now.
http://sourceforge.net/powerbar/db2/
_______________________________________________
linux-usb-devel@lists.sourceforge.net
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
