From: Peter Stokes <[EMAIL PROTECTED]>
Add logical channel support for ATI Remote Wonder II
The ATI Remote Wonder II can be configured with one of 16 unique logical
channels. Allowing up to 16 remotes to be used independently within
range of each other. This change adds functionality to configure the
receiver and filter the input data to respond or exclude remotes
configured with different logical channels.
Signed-off-by: Peter Stokes <[EMAIL PROTECTED]>
Acked-by: Ville Syrjala <[EMAIL PROTECTED]>
Signed-off-by: Greg Kroah-Hartman <[EMAIL PROTECTED]>
---
drivers/usb/input/ati_remote2.c | 89 +++++++++++++++++++++++++++++++++++----
1 files changed, 80 insertions(+), 9 deletions(-)
diff --git a/drivers/usb/input/ati_remote2.c b/drivers/usb/input/ati_remote2.c
index 83f1f79..6459be9 100644
--- a/drivers/usb/input/ati_remote2.c
+++ b/drivers/usb/input/ati_remote2.c
@@ -2,6 +2,7 @@
* ati_remote2 - ATI/Philips USB RF remote driver
*
* Copyright (C) 2005 Ville Syrjala <[EMAIL PROTECTED]>
+ * Copyright (C) 2007 Peter Stokes <[EMAIL PROTECTED]>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2
@@ -11,13 +12,29 @@
#include <linux/usb/input.h>
#define DRIVER_DESC "ATI/Philips USB RF remote driver"
-#define DRIVER_VERSION "0.1"
+#define DRIVER_VERSION "0.2"
MODULE_DESCRIPTION(DRIVER_DESC);
MODULE_VERSION(DRIVER_VERSION);
MODULE_AUTHOR("Ville Syrjala <[EMAIL PROTECTED]>");
MODULE_LICENSE("GPL");
+/*
+ * ATI Remote Wonder II Channel Configuration
+ *
+ * The remote control can by assigned one of sixteen "channels" in order to
facilitate
+ * the use of multiple remote controls within range of each other.
+ * A remote's "channel" may be altered by pressing and holding the "PC" button
for
+ * approximately 3 seconds, after which the button will slowly flash the count
of the
+ * currently configured "channel", using the numeric keypad enter a number
between 1 and
+ * 16 and then the "PC" button again, the button will slowly flash the count
of the
+ * newly configured "channel".
+ */
+
+static unsigned int channel_mask = 0xFFFF;
+module_param(channel_mask, uint, 0644);
+MODULE_PARM_DESC(channel_mask, "Bitmask of channels to accept
<15:Channel16>...<1:Channel2><0:Channel1>");
+
static unsigned int mode_mask = 0x1F;
module_param(mode_mask, uint, 0644);
MODULE_PARM_DESC(mode_mask, "Bitmask of modes to accept
<4:PC><3:AUX4><2:AUX3><1:AUX2><0:AUX1>");
@@ -146,15 +163,23 @@ static void ati_remote2_input_mouse(struct ati_remote2
*ar2)
{
struct input_dev *idev = ar2->idev;
u8 *data = ar2->buf[0];
+ int channel, mode;
+
+ channel = data[0] >> 4;
+
+ if (!((1 << channel) & channel_mask))
+ return;
- if (data[0] > 4) {
+ mode = data[0] & 0x0F;
+
+ if (mode > 4) {
dev_err(&ar2->intf[0]->dev,
"Unknown mode byte (%02x %02x %02x %02x)\n",
data[3], data[2], data[1], data[0]);
return;
}
- if (!((1 << data[0]) & mode_mask))
+ if (!((1 << mode) & mode_mask))
return;
input_event(idev, EV_REL, REL_X, (s8) data[1]);
@@ -177,9 +202,16 @@ static void ati_remote2_input_key(struct ati_remote2 *ar2)
{
struct input_dev *idev = ar2->idev;
u8 *data = ar2->buf[1];
- int hw_code, index;
+ int channel, mode, hw_code, index;
+
+ channel = data[0] >> 4;
+
+ if (!((1 << channel) & channel_mask))
+ return;
- if (data[0] > 4) {
+ mode = data[0] & 0x0F;
+
+ if (mode > 4) {
dev_err(&ar2->intf[1]->dev,
"Unknown mode byte (%02x %02x %02x %02x)\n",
data[3], data[2], data[1], data[0]);
@@ -199,16 +231,16 @@ static void ati_remote2_input_key(struct ati_remote2 *ar2)
* events for the mouse pad so we filter out any subsequent
* events from the same mode key.
*/
- if (ar2->mode == data[0])
+ if (ar2->mode == mode)
return;
if (data[1] == 0)
- ar2->mode = data[0];
+ ar2->mode = mode;
- hw_code |= data[0] << 8;
+ hw_code |= mode << 8;
}
- if (!((1 << data[0]) & mode_mask))
+ if (!((1 << mode) & mode_mask))
return;
index = ati_remote2_lookup(hw_code);
@@ -379,6 +411,41 @@ static void ati_remote2_urb_cleanup(struct ati_remote2
*ar2)
}
}
+static int ati_remote2_setup(struct ati_remote2 *ar2)
+{
+ int r, i, channel;
+
+ /*
+ * Configure receiver to only accept input from remote "channel"
+ * channel == 0 -> Accept input from any remote channel
+ * channel == 1 -> Only accept input from remote channel 1
+ * channel == 2 -> Only accept input from remote channel 2
+ * ...
+ * channel == 16 -> Only accept input from remote channel 16
+ */
+
+ channel = 0;
+ for (i = 0; i < 16; i++) {
+ if ((1 << i) & channel_mask) {
+ if (!(~(1 << i) & 0xFFFF & channel_mask))
+ channel = i + 1;
+ break;
+ }
+ }
+
+ r = usb_control_msg(ar2->udev, usb_sndctrlpipe(ar2->udev, 0),
+ 0x20,
+ USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_INTERFACE,
+ channel, 0x0, NULL, 0, USB_CTRL_SET_TIMEOUT);
+ if (r) {
+ dev_err(&ar2->udev->dev, "%s - failed to set channel due to
error: %d\n",
+ __FUNCTION__, r);
+ return r;
+ }
+
+ return 0;
+}
+
static int ati_remote2_probe(struct usb_interface *interface, const struct
usb_device_id *id)
{
struct usb_device *udev = interface_to_usbdev(interface);
@@ -409,6 +476,10 @@ static int ati_remote2_probe(struct usb_interface
*interface, const struct usb_d
if (r)
goto fail2;
+ r = ati_remote2_setup(ar2);
+ if (r)
+ goto fail2;
+
usb_make_path(udev, ar2->phys, sizeof(ar2->phys));
strlcat(ar2->phys, "/input0", sizeof(ar2->phys));
--
1.5.1.2
-------------------------------------------------------------------------
This SF.net email is sponsored by DB2 Express
Download DB2 Express C - the FREE version of DB2 express and take
control of your XML. No limits. Just data. Click to get it now.
http://sourceforge.net/powerbar/db2/
_______________________________________________
[email protected]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
