Hey all, When trying CONFIG_USB_SUSPEND with my Dell Latitude D820, I found that the SGS Thomson Micro fingerprint reader (the same as found in Thinkpads, http://thinkfinger.sourceforge.net/) is rendered inoperable. When I attempt to prove the device (e.g. with lsusb), the device connects to the bus, the kernel discovers it, only to encounter a hub port error (-71) and disable it. This will continue every time I run lsusb, although occasionally I will catch the device in the right stage of the failure, allowing me to see the device in lsusb for a short period of time each cycle, yielding the following lsusb entry: Bus 003 Device 042: ID 0483:2016 SGS Thomson Microelectronics Fingerprint Reader
Each cycle, the device has a different device ID. Additionally, if I run lsusb --verbose, I get the following errors: cannot read device status, Protocol error (71) can't get hub descriptor: Protocol error cannot read device status, Protocol error (71) Accompanied by the following errors in dmesg: usb 3-1.2: usbfs: USBDEVFS_CONTROL failed cmd lsusb rqt 128 rq 6 len 255 ret -71 usb 3-1.2: usbfs: USBDEVFS_CONTROL failed cmd lsusb rqt 128 rq 6 len 255 ret -71 usb 3-1.2: usbfs: USBDEVFS_CONTROL failed cmd lsusb rqt 128 rq 0 len 2 ret -71 usb 3-1: usbfs: USBDEVFS_CONTROL failed cmd lsusb rqt 160 rq 6 len 13 ret -71 usb 3-1: usbfs: USBDEVFS_CONTROL failed cmd lsusb rqt 128 rq 0 len 2 ret -71 hub 3-0:1.0: port 1 disabled by hub (EMI?), re-enabling... While the device is occassionally visible in lsusb (although never with --verbose AFAICT), it is never in operable enough a state long enough for the driver to use it. The device works fine when CONFIG_USB_SUSPEND is disabled. The output of dmesg is given below. This message (http://article.gmane.org/gmane.linux.drivers.thinkfinger/362) seems to suggest at least some others are succesfully using the device with suspend although I don't know that for a fact. I am presently running kernel 2.6.21 although this same failure has been exhibited in earlier kernels (at least 2.6.20) in the past. Anyone have any ideas as to what might cause this failure? Is it the device? The hub? The kernel USB subsystem? If any more information is necessary to diagnose this failure, I'd be more than happy to provide it. Anyways, thanks a ton, - Ben Gamari dmesg: ======================= Linux version 2.6.21 ([EMAIL PROTECTED]) (gcc version 4.1.1 (Gentoo 4.1.1-r3)) #7 SMP Sun May 13 14:00:13 EDT 2007 BIOS-provided physical RAM map: sanitize start sanitize end copy_e820_map() start: 0000000000000000 size: 000000000009f000 end: 000000000009f000 type: 1 copy_e820_map() type is E820_RAM copy_e820_map() start: 000000000009f000 size: 0000000000001000 end: 00000000000a0000 type: 2 copy_e820_map() start: 0000000000100000 size: 000000003fd81400 end: 000000003fe81400 type: 1 copy_e820_map() type is E820_RAM copy_e820_map() start: 000000003fe81400 size: 000000000017ec00 end: 0000000040000000 type: 2 copy_e820_map() start: 00000000f0000000 size: 0000000004007000 end: 00000000f4007000 type: 2 copy_e820_map() start: 00000000f4008000 size: 0000000000004000 end: 00000000f400c000 type: 2 copy_e820_map() start: 00000000fec00000 size: 0000000000010000 end: 00000000fec10000 type: 2 copy_e820_map() start: 00000000fed20000 size: 0000000000080000 end: 00000000feda0000 type: 2 copy_e820_map() start: 00000000fee00000 size: 0000000000010000 end: 00000000fee10000 type: 2 copy_e820_map() start: 00000000ffb00000 size: 0000000000500000 end: 0000000100000000 type: 2 BIOS-e820: 0000000000000000 - 000000000009f000 (usable) BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) BIOS-e820: 0000000000100000 - 000000003fe81400 (usable) BIOS-e820: 000000003fe81400 - 0000000040000000 (reserved) BIOS-e820: 00000000f0000000 - 00000000f4007000 (reserved) BIOS-e820: 00000000f4008000 - 00000000f400c000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved) BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) 126MB HIGHMEM available. 896MB LOWMEM available. Entering add_active_range(0, 0, 261761) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 229376 HighMem 229376 -> 261761 early_node_map[1] active PFN ranges 0: 0 -> 261761 On node 0 totalpages: 261761 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 1760 pages used for memmap Normal zone: 223520 pages, LIFO batch:31 HighMem zone: 253 pages used for memmap HighMem zone: 32132 pages, LIFO batch:7 DMI 2.4 present. ACPI: RSDP 000FC0C0, 0014 (r0 DELL ) ACPI: RSDT 3FE8198A, 0044 (r1 DELL M07 27D70402 ASL 61) ACPI: FACP 3FE82800, 0074 (r1 DELL M07 27D70402 ASL 61) ACPI: DSDT 3FE83400, 5487 (r1 INT430 SYSFexxx 1001 INTL 20050624) ACPI: FACS 3FE91C00, 0040 ACPI: HPET 3FE82F00, 0038 (r1 DELL M07 1 ASL 61) ACPI: APIC 3FE83000, 0068 (r1 DELL M07 27D70402 ASL 47) ACPI: ASF! 3FE82C00, 005B (r16 DELL M07 27D70402 ASL 61) ACPI: MCFG 3FE82FC0, 003E (r16 DELL M07 27D70402 ASL 61) ACPI: SLIC 3FE8309C, 0176 (r1 DELL M07 27D70402 ASL 61) ACPI: TCPA 3FE83300, 0032 (r1 DELL M07 27D70402 ASL 61) ACPI: SSDT 3FE81A11, 04DC (r1 PmRef CpuPm 3000 INTL 20050624) ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 6:14 APIC version 20 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 6:14 APIC version 20 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs ACPI: HPET id: 0x8086a201 base: 0xfed00000 Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:b0000000) Built 1 zonelists. Total pages: 259716 Kernel command line: root=/dev/sda1 mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 2161.411 MHz processor. Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1032312k/1047044k available (2881k kernel code, 14176k reserved, 1316k data, 244k init, 129540k highmem) virtual kernel memory layout: fixmap : 0xffe17000 - 0xfffff000 (1952 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) .init : 0xc0521000 - 0xc055e000 ( 244 kB) .data : 0xc03d06c7 - 0xc0519754 (1316 kB) .text : 0xc0100000 - 0xc03d06c7 (2881 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 hpet0: 3 64-bit timers, 14318180 Hz Calibrating delay using timer specific routine.. 4326.82 BogoMIPS (lpj=8653650) Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000 monitor/mwait feature present. using mwait in idle threads. CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 CPU: After all inits, caps: bfe9fbff 00100000 00000000 00002940 0000c1a9 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code ACPI: Core revision 20070126 Parsing all Control Methods: Table [DSDT](id 0001) - 702 Objects with 96 Devices 257 Methods 12 Regions Parsing all Control Methods: Table [SSDT](id 0002) - 13 Objects with 0 Devices 4 Methods 0 Regions tbxface-0587 [02] tb_load_namespace : ACPI Tables successfully acquired evxfevnt-0091 [02] enable : Transition to ACPI mode successful CPU0: Intel Genuine Intel(R) CPU T2600 @ 2.16GHz stepping 08 SMP alternatives: switching to SMP code Booting processor 1/1 eip 3000 Initializing CPU#1 Calibrating delay using timer specific routine.. 4322.54 BogoMIPS (lpj=8645080) CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000 monitor/mwait feature present. CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 CPU: After all inits, caps: bfe9fbff 00100000 00000000 00002940 0000c1a9 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel Genuine Intel(R) CPU T2600 @ 2.16GHz stepping 08 Total of 2 processors activated (8649.36 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization [CPU#0 -> CPU#1]: Measured 4550300547 cycles TSC warp between CPUs, turning off TSC clock. Brought up 2 CPUs migration_cost=4000 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG Setting up standard PCI resources evgpeblk-0952 [04] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9 evgpeblk-1049 [03] ev_initialize_gpe_bloc: Found 9 Wake, Enabled 3 Runtime GPEs in this block Completing Region/Field/Buffer/Package initialization:......................................................................... Initialized 10/12 Regions 14/16 Fields 32/33 Buffers 17/28 Packages (724 nodes) Initializing Device/Processor/Thermal objects by executing _INI methods:...ACPI Warning (tbutils-0158): Incorrect checksum in table [TCPA] - 00, should be AA [20070126] ACPI: SSDT 3FE819CE, 0043 (r1 LMPWR DELLLOM 1001 INTL 20050624) Parsing all Control Methods: Table [SSDT](id 00A2) - 1 Objects with 0 Devices 1 Methods 0 Regions . Executed 4 _INI methods requiring 0 _STA executions (examined 101 objects) ACPI: Interpreter enabled ACPI: (supports S0 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO PCI quirk: region 1080-10bf claimed by ICH6 GPIO Boot video device is 0000:01:00.0 PCI: Transparent bridge - 0000:00:1e.0 PCI: Bus #04 (-#07) is hidden behind transparent bridge #03 (-#04) (try 'pci=assign-busses') Please report the result to linux-kernel to fix this permanently ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PXP0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs *9 10 11) ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *3 ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 11) *5 ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 *11) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 14 devices SCSI subsystem initialized libata version 2.20 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:00: iomem range 0x0-0x9fbff could not be reserved pnp: 00:00: iomem range 0x9fc00-0x9ffff could not be reserved pnp: 00:00: iomem range 0xc0000-0xcffff could not be reserved Time: hpet clocksource has been installed. pnp: 00:00: iomem range 0xe0000-0xfffff could not be reserved pnp: 00:02: ioport range 0x4d0-0x4d1 has been reserved pnp: 00:02: ioport range 0x1000-0x1005 has been reserved pnp: 00:02: ioport range 0x1008-0x100f has been reserved pnp: 00:03: ioport range 0xf400-0xf4fe has been reserved pnp: 00:03: ioport range 0x1006-0x1007 has been reserved pnp: 00:03: ioport range 0x100a-0x1059 could not be reserved pnp: 00:03: ioport range 0x1060-0x107f has been reserved pnp: 00:03: ioport range 0x1080-0x10bf has been reserved pnp: 00:03: ioport range 0x10c0-0x10df has been reserved pnp: 00:08: ioport range 0xc80-0xcaf has been reserved pnp: 00:08: ioport range 0xcc0-0xcff could not be reserved pnp: 00:08: ioport range 0x910-0x91f has been reserved pnp: 00:08: ioport range 0x920-0x92f has been reserved pnp: 00:08: ioport range 0xcbc-0xcbf has been reserved pnp: 00:08: ioport range 0x930-0x97f has been reserved pnp: 00:0b: iomem range 0xfed00000-0xfed003ff could not be reserved pnp: 00:0d: ioport range 0xcb0-0xcbb has been reserved pnp: 00:0d: iomem range 0xfed40000-0xfed44fff could not be reserved PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: ed000000-efefffff PREFETCH window: d0000000-dfffffff PCI: Bridge: 0000:00:1c.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.1 IO window: disabled. MEM window: ecf00000-ecffffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.2 IO window: disabled. MEM window: ece00000-ecefffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.3 IO window: e000-efff MEM window: ecc00000-ecdfffff PREFETCH window: e0000000-e01fffff PCI: Bus 4, cardbus bridge: 0000:03:01.0 IO window: 00002000-000020ff IO window: 00002400-000024ff PREFETCH window: 50000000-53ffffff MEM window: 54000000-57ffffff PCI: Bridge: 0000:00:1e.0 IO window: 2000-2fff MEM window: ecb00000-ecbfffff PREFETCH window: 50000000-53ffffff ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:01.0 to 64 ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1c.0 to 64 ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1c.1 to 64 ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1c.2 to 64 ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1c.3 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 PCI: Enabling device 0000:03:01.0 (0000 -> 0003) ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 19 (level, low) -> IRQ 19 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1572864 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered Machine check exception polling timer started. IA-32 Microcode Update Driver: v1.14a <[EMAIL PROTECTED]> highmem bounce pool size: 64 pages Total HugeTLB memory allocated, 0 Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]). io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered PCI: Setting latency timer of device 0000:00:01.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:01.0:pcie00] Allocate Port Service[0000:00:01.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.0:pcie00] Allocate Port Service[0000:00:1c.0:pcie02] Allocate Port Service[0000:00:1c.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.1 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.1:pcie00] Allocate Port Service[0000:00:1c.1:pcie02] Allocate Port Service[0000:00:1c.1:pcie03] PCI: Setting latency timer of device 0000:00:1c.2 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.2:pcie00] Allocate Port Service[0000:00:1c.2:pcie02] Allocate Port Service[0000:00:1c.2:pcie03] PCI: Setting latency timer of device 0000:00:1c.3 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.3:pcie00] Allocate Port Service[0000:00:1c.3:pcie02] Allocate Port Service[0000:00:1c.3:pcie03] ACPI: AC Adapter [AC] (on-line) ACPI: Battery Slot [BAT0] (battery present) ACPI: Battery Slot [BAT1] (battery absent) input: Lid Switch as /class/input/input0 ACPI: Lid Switch [LID] input: Power Button (CM) as /class/input/input1 ACPI: Power Button (CM) [PBTN] input: Sleep Button (CM) as /class/input/input2 ACPI: Sleep Button (CM) [SBTN] ACPI: SSDT 3FE82138, 0244 (r1 PmRef Cpu0Ist 3000 INTL 20050624) Parsing all Control Methods: Table [SSDT](id 000A) - 6 Objects with 0 Devices 4 Methods 0 Regions ACPI: SSDT 3FE81EED, 01C6 (r1 PmRef Cpu0Cst 3001 INTL 20050624) Parsing all Control Methods: Table [SSDT](id 000B) - 1 Objects with 0 Devices 1 Methods 0 Regions ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: SSDT 3FE8237C, 00C4 (r1 PmRef Cpu1Ist 3000 INTL 20050624) Parsing all Control Methods: Table [SSDT](id 000F) - 4 Objects with 0 Devices 4 Methods 0 Regions ACPI: SSDT 3FE820B3, 0085 (r1 PmRef Cpu1Cst 3000 INTL 20050624) Parsing all Control Methods: Table [SSDT](id 0010) - 1 Objects with 0 Devices 1 Methods 0 Regions ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU1] (supports 8 throttling states) ACPI: Thermal Zone [THM] (42 C) Real Time Clock Driver v1.12ac hpet_resources: 0xfed00000 is busy ACPI Error (utglobal-0128): Unknown exception code: 0xFFFFFFF0 [20070126] Non-volatile memory driver v1.2 Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds). Hangcheck: Using get_cycles(). Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A Floppy drive(s): fd0 is 1.44M Clocksource tsc unstable (delta = -312963945 ns) floppy0: no floppy controllers found RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <[EMAIL PROTECTED]> netconsole: not configured, aborting 3ware Storage Controller device driver for Linux v1.26.02.002. ata_piix 0000:00:1f.2: version 2.10ac1 ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1f.2 to 64 ata1: SATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001bfa0 irq 14 ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001bfa8 irq 15 scsi0 : ata_piix ata1.00: ATA-7: Hitachi HTS721010G9SA00, MCZOC10H, max UDMA/100 ata1.00: 195371568 sectors, multi 8: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/100 scsi1 : ata_piix ata2.00: ATAPI, max UDMA/33 ata2.00: configured for UDMA/33 scsi 0:0:0:0: Direct-Access ATA Hitachi HTS72101 MCZO PQ: 0 ANSI: 5 SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sd 0:0:0:0: Attached scsi disk sda sd 0:0:0:0: Attached scsi generic sg0 type 0 scsi 1:0:0:0: CD-ROM _NEC DVD+-RW ND-6650A 102C PQ: 0 ANSI: 5 sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 1:0:0:0: Attached scsi CD-ROM sr0 sr 1:0:0:0: Attached scsi generic sg1 type 5 usbmon: debugfs is not available ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 20, io mem 0xffa80000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000bf80 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 21 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.1: irq 21, io base 0x0000bf60 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 22 (level, low) -> IRQ 22 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.2: irq 22, io base 0x0000bf40 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 23 (level, low) -> IRQ 23 PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.3: irq 23, io base 0x0000bf20 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected usb 2-2: new full speed USB device using uhci_hcd and address 2 usb 2-2: configuration #1 chosen from 1 choice hub 2-2:1.0: USB hub found hub 2-2:1.0: 4 ports detected usb 3-1: new full speed USB device using uhci_hcd and address 2 usb 3-1: configuration #1 chosen from 1 choice hub 3-1:1.0: USB hub found hub 3-1:1.0: 3 ports detected usb 2-2.3: new full speed USB device using uhci_hcd and address 3 usb 2-2.3: configuration #1 chosen from 1 choice usb 3-1.1: new full speed USB device using uhci_hcd and address 3 usb 3-1.1: configuration #1 chosen from 1 choice usb 3-1.2: new full speed USB device using uhci_hcd and address 4 usb 3-1.2: configuration #1 chosen from 1 choice usbcore: registered new interface driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input3 device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [EMAIL PROTECTED] input: PS/2 Mouse as /class/input/input4 input: AlpsPS/2 ALPS GlidePoint as /class/input/input5 dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) Advanced Linux Sound Architecture Driver Version 1.0.14rc3 (Wed Mar 14 07:25:50 2007 UTC). ALSA device list: No soundcards found. oprofile: using NMI interrupt. TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 10 Mobile IPv6 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 Using IPI No-Shortcut mode ReiserFS: sda1: found reiserfs format "3.6" with standard journal ReiserFS: sda1: using ordered data mode ReiserFS: sda1: journal params: device sda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: sda1: checking transaction log (sda1) ReiserFS: sda1: replayed 604 transactions in 6 seconds ReiserFS: sda1: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 244k freed ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1b.0 to 64 Linux agpgart interface v0.102 (c) Dave Jones Bluetooth: Core ver 2.11 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: HCI USB driver ver 2.9 usbcore: registered new interface driver hci_usb tg3.c:v3.75 (March 23, 2007) ACPI: PCI Interrupt 0000:09:00.0[A] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:09:00.0 to 64 agpgart: Detected an Intel 945GM Chipset. agpgart: AGP aperture is 256M @ 0x0 eth0: Tigon3 [partno(BCM5752KFBG) rev 6002 PHY(5752)] (PCI Express) 10/100/1000Base-T Ethernet 00:15:c5:b8:f9:cb eth0: RXcsums[1] LinkChgREG[1] MIirq[1] ASF[0] WireSpeed[1] TSOcap[1] eth0: dma_rwctrl[76180000] dma_mask[64-bit] nvidia: module license 'NVIDIA' taints kernel. ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:01:00.0 to 64 NVRM: loading NVIDIA UNIX x86 Kernel Module 1.0-9755 Mon Feb 26 23:21:15 PST 2007 ReiserFS: sda1: Removing [2570292 2570294 0x0 SD]..done ReiserFS: sda1: Removing [18725 2567216 0x0 SD]..done ReiserFS: sda1: Removing [2529400 2529490 0x0 SD]..done ReiserFS: sda1: Removing [2529380 2529381 0x0 SD]..done ReiserFS: sda1: Removing [2521296 2521298 0x0 SD]..done ReiserFS: sda1: Removing [2521295 2521297 0x0 SD]..done ReiserFS: sda1: Removing [8504 2520803 0x0 SD]..done ReiserFS: sda1: Removing [6162 2443556 0x0 SD]..done ReiserFS: sda1: Removing [6162 2443493 0x0 SD]..done ReiserFS: sda1: Removing [2334194 2329284 0x0 SD]..done ReiserFS: sda1: Removing [18725 2132564 0x0 SD]..done ReiserFS: sda1: Removing [6162 1949666 0x0 SD]..done ReiserFS: sda1: Removing [1949390 1949391 0x0 SD]..done ReiserFS: sda1: Removing [1948688 1948717 0x0 SD]..done ReiserFS: sda1: Removing [1948688 1948703 0x0 SD]..done ReiserFS: sda1: Removing [1948688 1948696 0x0 SD]..done ReiserFS: sda1: Removing [6162 1943588 0x0 SD]..done ReiserFS: sda1: Removing [8504 1794090 0x0 SD]..done ReiserFS: sda1: Removing [18725 1632010 0x0 SD]..done ReiserFS: sda1: Removing [18721 362928 0x0 SD]..done ReiserFS: sda1: Removing [8504 293227 0x0 SD]..done ReiserFS: sda1: There were 21 uncompleted unlinks/truncates. Completed Adding 2955952k swap on /dev/sda2. Priority:-1 extents:1 across:2955952k hub 3-1:1.0: hub_port_status failed (err = -71) hub 3-1:1.0: cannot disable port 1 (err = -71) hub 3-1:1.0: hub_port_status failed (err = -71) hub 3-0:1.0: port 1 disabled by hub (EMI?), re-enabling... usb 3-1: USB disconnect, address 2 usb 3-1.1: USB disconnect, address 3 usb 3-1.2: USB disconnect, address 4 usb 3-1: new full speed USB device using uhci_hcd and address 5 usb 3-1: configuration #1 chosen from 1 choice hub 3-1:1.0: USB hub found hub 3-1:1.0: 3 ports detected usb 3-1.1: new full speed USB device using uhci_hcd and address 6 usb 3-1.1: configuration #1 chosen from 1 choice usb 3-1.2: new full speed USB device using uhci_hcd and address 7 usb 3-1.2: configuration #1 chosen from 1 choice PM: Writing back config space on device 0000:09:00.0 at offset c (was 22540000, writing 0) PM: Writing back config space on device 0000:09:00.0 at offset 1 (was 100506, writing 100106) ADDRCONF(NETDEV_UP): eth0: link is not ready input: Virtual ThinkFinger Keyboard as /class/input/input6 hub 3-1:1.0: hub_port_status failed (err = -71) hub 3-1:1.0: cannot disable port 1 (err = -71) hub 3-1:1.0: hub_port_status failed (err = -71) hub 3-0:1.0: port 1 disabled by hub (EMI?), re-enabling... usb 3-1: USB disconnect, address 5 usb 3-1.1: USB disconnect, address 6 usb 3-1.2: USB disconnect, address 7 usb 3-1: new full speed USB device using uhci_hcd and address 8 usb 3-1: configuration #1 chosen from 1 choice hub 3-1:1.0: USB hub found hub 3-1:1.0: 3 ports detected usb 3-1.1: new full speed USB device using uhci_hcd and address 9 usb 3-1.1: configuration #1 chosen from 1 choice usb 3-1.2: new full speed USB device using uhci_hcd and address 10 usb 3-1.2: configuration #1 chosen from 1 choice input: Virtual ThinkFinger Keyboard as /class/input/input7 hub 3-1:1.0: hub_port_status failed (err = -71) hub 3-1:1.0: cannot disable port 1 (err = -71) hub 3-1:1.0: hub_port_status failed (err = -71) hub 3-0:1.0: port 1 disabled by hub (EMI?), re-enabling... usb 3-1: USB disconnect, address 8 usb 3-1.1: USB disconnect, address 9 usb 3-1.2: USB disconnect, address 10 usb 3-1: new full speed USB device using uhci_hcd and address 11 usb 3-1: configuration #1 chosen from 1 choice hub 3-1:1.0: USB hub found hub 3-1:1.0: 3 ports detected usb 3-1.1: new full speed USB device using uhci_hcd and address 12 usb 3-1.1: configuration #1 chosen from 1 choice usb 3-1.2: new full speed USB device using uhci_hcd and address 13 usb 3-1.2: configuration #1 chosen from 1 choice input: Virtual ThinkFinger Keyboard as /class/input/input8 hub 3-1:1.0: hub_port_status failed (err = -71) hub 3-1:1.0: cannot disable port 1 (err = -71) hub 3-1:1.0: hub_port_status failed (err = -71) hub 3-0:1.0: port 1 disabled by hub (EMI?), re-enabling... usb 3-1: USB disconnect, address 11 usb 3-1.1: USB disconnect, address 12 usb 3-1.2: USB disconnect, address 13 usb 3-1: new full speed USB device using uhci_hcd and address 14 usb 3-1: configuration #1 chosen from 1 choice hub 3-1:1.0: USB hub found hub 3-1:1.0: 3 ports detected usb 3-1.1: new full speed USB device using uhci_hcd and address 15 usb 3-1.1: configuration #1 chosen from 1 choice usb 3-1.2: new full speed USB device using uhci_hcd and address 16 usb 3-1.2: configuration #1 chosen from 1 choice UDF-fs: Partition marked readonly; forcing readonly mount UDF-fs INFO UDF 0.9.8.1 (2004/29/09) Mounting volume 'Pursuit Of Happyness, The', timestamp 2007/01/27 11:21 (1f10) atkbd.c: Unknown key pressed (translated set 2, code 0x86 on isa0060/serio0). atkbd.c: Use 'setkeycodes e006 <keycode>' to make it known. iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 0.0.19kd iwl3945: Copyright(c) 2003-2007 Intel Corporation ACPI: PCI Interrupt 0000:0c:00.0[A] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:0c:00.0 to 64 iwl3945: Detected Intel PRO/Wireless 3945ABG Network Connection iwl3945: Channel 12 [2.4GHz] is Tx only -- skipping. iwl3945: Channel 13 [2.4GHz] is Tx only -- skipping. iwl3945: Channel 14 [2.4GHz] is Tx only -- skipping. iwl3945: Channel 183 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 184 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 185 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 187 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 188 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 189 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 192 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 196 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 7 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 8 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 11 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 12 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 16 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 34 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 38 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 42 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 46 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 100 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 104 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 108 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 112 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 116 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 120 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 124 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 128 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 132 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 136 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 140 [5.2GHz] is Tx only -- skipping. iwl3945: Channel 145 [5.2GHz] is Tx only -- skipping. iwl3945: Tunable channels: 11 802.11bg, 13 802.11a channels wmaster0: Selected rate control algorithm 'iwl-3945-rs' wmaster0: Does not support passive scan, disabled ADDRCONF(NETDEV_UP): wlan0: link is not ready iwl3945: REPLY_ADD_STA failed wlan0: Initial auth_alg=0 wlan0: authenticate with AP 00:14:bf:45:1d:2b wlan0: RX authentication from 00:14:bf:45:1d:2b (alg=0 transaction=2 status=0) wlan0: authenticated wlan0: associate with AP 00:14:bf:45:1d:2b wlan0: RX AssocResp from 00:14:bf:45:1d:2b (capab=0x411 status=0 aid=2) wlan0: associated ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready wlan0: duplicate address detected! wlan0: duplicate address detected! atkbd.c: Unknown key pressed (translated set 2, code 0x93 on isa0060/serio0). atkbd.c: Use 'setkeycodes e013 <keycode>' to make it known. atkbd.c: Unknown key pressed (translated set 2, code 0x93 on isa0060/serio0). atkbd.c: Use 'setkeycodes e013 <keycode>' to make it known. atkbd.c: Unknown key pressed (translated set 2, code 0x86 on isa0060/serio0). atkbd.c: Use 'setkeycodes e006 <keycode>' to make it known. atkbd.c: Unknown key pressed (translated set 2, code 0x86 on isa0060/serio0). atkbd.c: Use 'setkeycodes e006 <keycode>' to make it known. atkbd.c: Unknown key pressed (translated set 2, code 0x86 on isa0060/serio0). atkbd.c: Use 'setkeycodes e006 <keycode>' to make it known. hub 3-1:1.0: hub_port_status failed (err = -71) hub 3-1:1.0: cannot disable port 1 (err = -71) hub 3-1:1.0: hub_port_status failed (err = -71) hub 3-1:1.0: hub_port_status failed (err = -71) hub 3-0:1.0: port 1 disabled by hub (EMI?), re-enabling... usb 3-1: USB disconnect, address 14 usb 3-1.1: USB disconnect, address 15 usb 3-1.2: USB disconnect, address 16 usb 3-1: new full speed USB device using uhci_hcd and address 17 usb 3-1: configuration #1 chosen from 1 choice hub 3-1:1.0: USB hub found hub 3-1:1.0: 3 ports detected usb 3-1.1: new full speed USB device using uhci_hcd and address 18 usb 3-1.1: configuration #1 chosen from 1 choice usb 3-1.2: new full speed USB device using uhci_hcd and address 19 usb 3-1.2: configuration #1 chosen from 1 choice hub 3-1:1.0: hub_port_status failed (err = -71) hub 3-1:1.0: cannot disable port 1 (err = -71) hub 3-1:1.0: hub_port_status failed (err = -71) hub 3-0:1.0: port 1 disabled by hub (EMI?), re-enabling... usb 3-1: USB disconnect, address 17 usb 3-1.1: USB disconnect, address 18 usb 3-1.2: USB disconnect, address 19 usb 3-1: new full speed USB device using uhci_hcd and address 20 usb 3-1: configuration #1 chosen from 1 choice hub 3-1:1.0: USB hub found hub 3-1:1.0: 3 ports detected usb 3-1.1: new full speed USB device using uhci_hcd and address 21 usb 3-1.1: configuration #1 chosen from 1 choice usb 3-1.2: new full speed USB device using uhci_hcd and address 22 usb 3-1.2: configuration #1 chosen from 1 choice ------------------------------------------------------------------------- This SF.net email is sponsored by DB2 Express Download DB2 Express C - the FREE version of DB2 express and take control of your XML. No limits. Just data. Click to get it now. http://sourceforge.net/powerbar/db2/ _______________________________________________ [email protected] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
