This is a note to let you know that I've just added the patch titled
Subject: UHCI: short control URBs get a status stage
to my gregkh-2.6 tree. Its filename is
uhci-short-control-urbs-get-a-status-stage.patch
This tree can be found at
http://www.kernel.org/pub/linux/kernel/people/gregkh/gregkh-2.6/patches/
>From [EMAIL PROTECTED] Fri Jul 13 12:46:32 2007
From: Alan Stern <[EMAIL PROTECTED]>
Date: Fri, 13 Jul 2007 15:46:29 -0400 (EDT)
Subject: UHCI: short control URBs get a status stage
To: Greg KH <[EMAIL PROTECTED]>
Cc: USB development list <linux-usb-devel@lists.sourceforge.net>
Message-ID: <[EMAIL PROTECTED]>
It has recently been pointed out that short control transfers should
have a status stage, even if they generate an error because
URB_SHORT_NOT_OK was set. This patch (as935) changes uhci-hcd to
enable the status stage when this happens.
Signed-off-by: Alan Stern <[EMAIL PROTECTED]>
Signed-off-by: Greg Kroah-Hartman <[EMAIL PROTECTED]>
---
drivers/usb/host/uhci-q.c | 59 +++++++++++++++++++++++++++++-----------------
1 file changed, 38 insertions(+), 21 deletions(-)
--- a/drivers/usb/host/uhci-q.c
+++ b/drivers/usb/host/uhci-q.c
@@ -827,8 +827,10 @@ static int uhci_submit_control(struct uh
* If direction is "send", change the packet ID from SETUP (0x2D)
* to OUT (0xE1). Else change it from SETUP to IN (0x69) and
* set Short Packet Detect (SPD) for all data packets.
+ *
+ * 0-length transfers always get treated as "send".
*/
- if (usb_pipeout(urb->pipe))
+ if (usb_pipeout(urb->pipe) || len == 0)
destination ^= (USB_PID_SETUP ^ USB_PID_OUT);
else {
destination ^= (USB_PID_SETUP ^ USB_PID_IN);
@@ -839,7 +841,12 @@ static int uhci_submit_control(struct uh
* Build the DATA TDs
*/
while (len > 0) {
- int pktsze = min(len, maxsze);
+ int pktsze = maxsze;
+
+ if (len <= pktsze) { /* The last data packet */
+ pktsze = len;
+ status &= ~TD_CTRL_SPD;
+ }
td = uhci_alloc_td(uhci);
if (!td)
@@ -866,20 +873,10 @@ static int uhci_submit_control(struct uh
goto nomem;
*plink = LINK_TO_TD(td);
- /*
- * It's IN if the pipe is an output pipe or we're not expecting
- * data back.
- */
- destination &= ~TD_TOKEN_PID_MASK;
- if (usb_pipeout(urb->pipe) || !urb->transfer_buffer_length)
- destination |= USB_PID_IN;
- else
- destination |= USB_PID_OUT;
-
+ /* Change direction for the status transaction */
+ destination ^= (USB_PID_IN ^ USB_PID_OUT);
destination |= TD_TOKEN_TOGGLE; /* End in Data1 */
- status &= ~TD_CTRL_SPD;
-
uhci_add_td_to_urbp(td, urbp);
uhci_fill_td(td, status | TD_CTRL_IOC,
destination | uhci_explen(0), 0);
@@ -1185,10 +1182,18 @@ static int uhci_result_common(struct uhc
}
}
+ /* Did we receive a short packet? */
} else if (len < uhci_expected_length(td_token(td))) {
- /* We received a short packet */
- if (urb->transfer_flags & URB_SHORT_NOT_OK)
+ /* For control transfers, go to the status TD if
+ * this isn't already the last data TD */
+ if (qh->type == USB_ENDPOINT_XFER_CONTROL) {
+ if (td->list.next != urbp->td_list.prev)
+ ret = 1;
+ }
+
+ /* For bulk and interrupt, this may be an error */
+ else if (urb->transfer_flags & URB_SHORT_NOT_OK)
ret = -EREMOTEIO;
/* Fixup needed only if this isn't the URB's last TD */
@@ -1208,10 +1213,6 @@ static int uhci_result_common(struct uhc
err:
if (ret < 0) {
- /* In case a control transfer gets an error
- * during the setup stage */
- urb->actual_length = max(urb->actual_length, 0);
-
/* Note that the queue has stopped and save
* the next toggle value */
qh->element = UHCI_PTR_TERM;
@@ -1489,9 +1490,25 @@ __acquires(uhci->lock)
{
struct urb_priv *urbp = (struct urb_priv *) urb->hcpriv;
+ if (qh->type == USB_ENDPOINT_XFER_CONTROL) {
+
+ /* urb->actual_length < 0 means the setup transaction didn't
+ * complete successfully. Either it failed or the URB was
+ * unlinked first. Regardless, don't confuse people with a
+ * negative length. */
+ urb->actual_length = max(urb->actual_length, 0);
+
+ /* Report erroneous short transfers */
+ if (unlikely((urb->transfer_flags & URB_SHORT_NOT_OK) &&
+ urb->actual_length <
+ urb->transfer_buffer_length &&
+ urb->status == 0))
+ urb->status = -EREMOTEIO;
+ }
+
/* When giving back the first URB in an Isochronous queue,
* reinitialize the QH's iso-related members for the next URB. */
- if (qh->type == USB_ENDPOINT_XFER_ISOC &&
+ else if (qh->type == USB_ENDPOINT_XFER_ISOC &&
urbp->node.prev == &qh->queue &&
urbp->node.next != &qh->queue) {
struct urb *nurb = list_entry(urbp->node.next,
Patches currently in gregkh-2.6 which might be from [EMAIL PROTECTED] are
driver/pm-remove-deprecated-sysfs-files.patch
driver/pm-remove-deprecated-dpm_runtime_-routines.patch
usb/usb-add-descriptors-binary-sysfs-attribute.patch
usb/usb-documentation-update-for-usb_unlink_urb.patch
usb/usb-fix-warning-caused-by-autosuspend-counter-going-negative.patch
usb/uhci-short-control-urbs-get-a-status-stage.patch
usb/isp116x-hcd-prepare-for-urb-status.patch
-------------------------------------------------------------------------
This SF.net email is sponsored by DB2 Express
Download DB2 Express C - the FREE version of DB2 express and take
control of your XML. No limits. Just data. Click to get it now.
http://sourceforge.net/powerbar/db2/
_______________________________________________
linux-usb-devel@lists.sourceforge.net
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
