Here's requested info:
# lsusb -v
T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 11/900 us ( 1%), #Int= 1, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.13-rc6-3124-smp uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:02:06.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 4
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0409 ProdID=0058 Rev= 1.00
S: Manufacturer=NEC Corporation
S: Product=USB2.0 Hub Controller
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=255ms
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc=106/900 us (12%), #Int= 1, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.13-rc6-3124-smp uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:02:06.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=051d ProdID=0002 Rev= 1.06
S: Manufacturer=American Power Conversion
S: Product=Back-UPS RS 1000 FW:7.g8 .D USB FW:g8
S: SerialNumber=JB0445024349
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 24mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid
E: Ad=81(I) Atr=03(Int.) MxPS= 6 Ivl=10ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.13-rc6-3124-smp uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:07.2
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.01 Cls=ff(vend.) Sub=ff Prot=ff MxPS= 8 #Cfgs= 1
P: Vendor=0545 ProdID=8002 Rev= 3.0a
S: Product=USB IMAGING DEVICE
C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=ibmcam
E: Ad=81(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 0 Alt= 1 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=ibmcam
E: Ad=81(I) Atr=01(Isoc) MxPS=1022 Ivl=1ms
I: If#= 1 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=82(I) Atr=02(Bulk) MxPS= 0 Ivl=0ms
I: If#= 1 Alt= 1 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=82(I) Atr=02(Bulk) MxPS=1022 Ivl=0ms
relevant USB PCI devices from "lspci -v":
00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
(prog-if 00 [UHCI])
Flags: bus master, medium devsel, latency 64, IRQ 19
I/O ports at dce0 [size=32]
02:06.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 61) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Flags: bus master, medium devsel, latency 64, IRQ 18
I/O ports at ece0 [size=32]
Capabilities: [80] Power Management version 2
02:06.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 61) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Flags: bus master, medium devsel, latency 64, IRQ 19
I/O ports at ecc0 [size=32]
Capabilities: [80] Power Management version 2
02:06.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 63)
(prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0
Flags: medium devsel, IRQ 16
Memory at fafffc00 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Here's the relevant lines from modprobe.conf
alias usb-controller uhci-hcd
alias char-major-188-* usbserial
alias usbdevfs usbcore
install usbmouse /sbin/modprobe --first-time --ignore-install usbmouse
&& { /sbin/modprobe hid; /bin/true; }
remove usbmouse { /sbin/modprobe -r hid; } ; /sbin/modprobe -r
--first-time --ignore-remove usbmouse
alias usb-uhci uhci-hcd
alias usb-ohci ohci-hcd
alias uhci uhci-hcd
alias usb-controller1 ohci-hcd
--
http://www.lightconsulting.com/~travis/ -><-
"We already have enough fast, insecure systems." -- Schneier & Ferguson
GPG fingerprint: 50A1 15C5 A9DE 23B9 ED98 C93E 38E9 204A 94C2 641B
-------------------------------------------------------
This SF.Net email is sponsored by the JBoss Inc.
Get Certified Today * Register for a JBoss Training Course
Free Certification Exam for All Training Attendees Through End of 2005
Visit http://www.jboss.com/services/certification for more information
_______________________________________________
[email protected]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users
