With 2.4.5 and my Visor when I try to synch the first time it start working and synch but thent it stop and I lost the connection, if I try a another sync after that it doesn't start at all. IN 2.4.4 everythings was find. I can still sync my DC5000 digital camera in 2.4.5. I think that usbserial add made a bad change somewhere. And worst then that in 2.4.5 if I try to /sbin/rmmod usbserial (after that I try to sync and after that /sbin/rmmod visor as been made), Xfree freeze (can't kill it with a ctrl-alt backspace) and surely because of the kernel that just crash. Usbserial, visor and dc2xx are alway's loaded since I load them at start-up. SO what do you think? Look down for some output of dmesg and proc in both kernel. ############IN 2.4.5 ################ dmesg uhci.c: wakeup_hc uhci.c: root-hub INT complete: port1: 93 port2: 80 data: 2 hub.c: port 1 connection change hub.c: port 1, portstatus 101, change 1, 12 Mb/s hub.c: port 1, portstatus 103, change 0, 12 Mb/s hub.c: USB new device connect on bus1/1, assigned device number 2 usb.c: kmalloc IF cb52cb80, numif 1 usb.c: new device strings: Mfr=1, Product=2, SerialNumber=0 usb.c: USB device number 2 default language ID 0x409 Manufacturer: Handspring Inc Product: Handspring Visor usbserial.c: Handspring Visor converter detected visor.c: Handspring Visor: Number of ports: 2 visor.c: Handspring Visor: port 1, is for Generic use and is bound to ttyUSB0 visor.c: Handspring Visor: port 2, is for HotSync use and is bound to ttyUSB1 usbserial.c: Handspring Visor converter now attached to ttyUSB0 (or usb/tts/0 for devfs) usbserial.c: Handspring Visor converter now attached to ttyUSB1 (or usb/tts/1 for devfs) usb.c: serial driver claimed interface cb52cb80 usb.c: kusbd: /sbin/hotplug add 2 cat /proc/bus/usb/devices T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 0.00 S: Product=USB UHCI-alt Root Hub S: SerialNumber=ff80 C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=16 #Cfgs= 1 P: Vendor=082d ProdID=0100 Rev= 1.00 S: Manufacturer=Handspring Inc S: Product=Handspring Visor C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA I: If#= 0 Alt= 0 #EPs= 4 Cls=ff(vend.) Sub=00 Prot=00 Driver=serial E: Ad=81(I) Atr=02(Bulk) MxPS= 16 Ivl= 10ms E: Ad=01(O) Atr=02(Bulk) MxPS= 16 Ivl= 0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl= 0ms /sbin/lsmod Module Size Used by emu10k1 43536 0 visor 8256 0 (unused) usbserial 16864 0 [visor] dc2xx 3872 0 (unused) NVdriver 658160 15 #######in 2.4.4 ####### dmesg hub.c: port 1 enable change, status 100 hub.c: port 1 connection change hub.c: port 1, portstatus 101, change 1, 12 Mb/s hub.c: port 1, portstatus 103, change 0, 12 Mb/s hub.c: USB new device connect on bus1/1, assigned device number 3 usb.c: kmalloc IF cc1783a0, numif 1 usb.c: new device strings: Mfr=1, Product=2, SerialNumber=0 usb.c: USB device number 3 default language ID 0x409 Manufacturer: Handspring Inc Product: Handspring Visor usbserial.c: Handspring Visor converter detected visor.c: Handspring Visor: Number of ports: 2 visor.c: Handspring Visor: port 1, is for Generic use and is bound to ttyUSB0 visor.c: Handspring Visor: port 2, is for HotSync use and is bound to ttyUSB1 usbserial.c: Handspring Visor converter now attached to ttyUSB0 (or usb/tts/0 for devfs) usbserial.c: Handspring Visor converter now attached to ttyUSB1 (or usb/tts/1 for devfs) usb.c: serial driver claimed interface cc1783a0 usb.c: kusbd: /sbin/hotplug add 3 cat /proc/bus/usb/devices T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 0.00 S: Product=USB UHCI Root Hub S: SerialNumber=ff80 C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=16 #Cfgs= 1 P: Vendor=082d ProdID=0100 Rev= 1.00 S: Manufacturer=Handspring Inc S: Product=Handspring Visor C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA I: If#= 0 Alt= 0 #EPs= 4 Cls=ff(vend.) Sub=00 Prot=00 Driver=serial E: Ad=81(I) Atr=02(Bulk) MxPS= 16 Ivl= 10ms E: Ad=01(O) Atr=02(Bulk) MxPS= 16 Ivl= 0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl= 0ms /sbin/lsmod Module Size Used by NVdriver 658288 15 emu10k1 44528 0 visor 8160 0 usbserial 16768 0 [visor] dc2xx 3744 0 (unused) I can remove mod without any problem -- Francis Fillion, BAA SI Broadcasting live from his linux box. And the maintainer of http://www.windplanet.com _______________________________________________ [EMAIL PROTECTED] To unsubscribe, use the last form field at: http://lists.sourceforge.net/lists/listinfo/linux-usb-users
