There is no USB controller there. You must have it deactived in your BIOS.
On Thu, 21 Mar 2002, Derek Cassidy wrote: > This is the output from lspci -vvv > > does this help? > > _____________________________________________________________________________ > cat lsp.txt > 00:00.0 Host bridge: Cyrix Corporation PCI Master > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > > 00:0c.0 VGA compatible controller: Chips and Technologies F69000 > HiQVideo (rev 64) (prog-if 00 [VGA]) > Subsystem: Chips and Technologies F69000 HiQVideo > Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping+ SERR- FastB2B- > Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Interrupt: pin A routed to IRQ 11 > Region 0: Memory at d8000000 (32-bit, non-prefetchable) [size=16M] > Expansion ROM at <unassigned> [disabled] [size=256K] > > 00:11.0 Ethernet controller: Intel Corporation 82559ER (rev 09) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 (2000ns min, 14000ns max), cache line size 08 > Interrupt: pin A routed to IRQ 10 > Region 0: Memory at db020000 (32-bit, non-prefetchable) [size=4K] > Region 1: I/O ports at e000 [size=64] > Region 2: Memory at db000000 (32-bit, non-prefetchable) [size=128K] > Expansion ROM at da000000 [disabled] [size=1M] > Capabilities: [dc] Power Management version 2 > Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA > PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable+ DSel=0 DScale=2 PME- > > 00:12.0 ISA bridge: Cyrix Corporation 5530 Legacy [Kahlua] (rev 30) > Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0, cache line size 04 > > 00:12.1 Bridge: Cyrix Corporation 5530 SMI [Kahlua] > Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Region 0: Memory at 40012000 (32-bit, non-prefetchable) [size=256] > > 00:12.2 IDE interface: Cyrix Corporation 5530 IDE [Kahlua] (prog-if 80 > [Master]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr- Stepping- SERR- FastB2B- > Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > Region 4: I/O ports at f000 [size=16] > > 00:12.3 Multimedia audio controller: Cyrix Corporation 5530 Audio [Kahlua] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > Region 0: Memory at 40011000 (32-bit, non-prefetchable) [size=128] > _____________________________________________________________________________ > > > [cassiddr@EMU cassiddr]$ > Stephen J. Gowdy wrote: > > > What does "lspci -vvv" say? > > > > On Thu, 21 Mar 2002, Derek Cassidy wrote: > > > >> Hello > >> I just tried to use a usb on a geode board from hitex and I cant get the > >> usb host controller to load. > >> I've tried all three, the usb-uhci, uhci, usb-ohci... but all three give > >> the same error > >> > >> "..usb-uhci.o: init_module: No such device.." > >> > >> I've enabled the USB in the BIOS so its not that. > >> > >> Can you tell me if theres many usb chips that are not supported by the > >> usb host controller drivers? or could the problem be something else? > >> > >> Thanks, > >> Derek > >> > >> > >> _______________________________________________ > >> [EMAIL PROTECTED] > >> To unsubscribe, use the last form field at: > >> https://lists.sourceforge.net/lists/listinfo/linux-usb-users > >> > -- /------------------------------------+-------------------------\ |Stephen J. Gowdy | SLAC, MailStop 34, | |http://www.slac.stanford.edu/~gowdy/ | 2575 Sand Hill Road, | |http://calendar.yahoo.com/gowdy | Menlo Park CA 94025, USA | |EMail: [EMAIL PROTECTED] | Tel: +1 650 926 3144 | \------------------------------------+-------------------------/ _______________________________________________ [EMAIL PROTECTED] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-users
