Hi,
i just subscribed to this mailing list. i've gotten myself a card reader recently, and so far i've been unsuccessful in getting this thing to work properly. i even took it over to a friends place, where i plugged it into his XP box, just to make sure the thing did work (it did :) so far, everything looks pretty good and normal to me, the device is recognized, but it seems like i can't get the media inside recognized. i used 3 different compact flash cards, to test it, all give the same result. i'll try to give as much information as possible, if i left something out, just say so and i'll supply whatever information that's required. my hardware is a Sunblade 100, running the sparclinux port Splack. i have a USB keyboard, mouse, and a kodak dc280, which are all working just fine using the usb connection. the usb cardreader is labelled "Microdia CF-SM combo card reader" i'm using kernel 2.4.19 (no patches applied) my kernel config looks like this: (relevant parts anyway:) CONFIG_HOTPLUG=y CONFIG_SCSI=m CONFIG_BLK_DEV_SD=m CONFIG_SD_EXTRA_DEVS=40 CONFIG_CHR_DEV_SG=m CONFIG_USB=y CONFIG_USB_DEVICEFS=y CONFIG_USB_OHCI=y CONFIG_USB_STORAGE=m CONFIG_USB_STORAGE_DEBUG=y CONFIG_USB_HID=y CONFIG_USB_HIDINPUT=y CONFIG_USB_DC2XX=m /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: CYPRESS Model: SM-CF 0.78 Rev: Type: Direct-Access ANSI SCSI revision: 02 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: CYPRESS Model: SM-CF 0.78 Rev: Type: Direct-Access ANSI SCSI revision: 02 from /proc/bus/usb/devices : T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 7 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=04ce ProdID=0002 Rev= 0.78 S: Manufacturer=CYPRESS SM-CF 0.78 S: Product=CYPRESS SM-CF 0.78 S: SerialNumber=11204EC7 C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=300mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms everything seems to be detected correctly, but then this happens: sdc : READ CAPACITY failed. sdc : status = 1, message = 00, host = 0, driver = 08 Current sd00:00: sns = 70 2 ASC=3a ASCQ= 0 Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 sdc : block size assumed to be 512 bytes, disk size 1GB. sdc: I/O error: dev 08:20, sector 0 I/O error: dev 08:20, sector 0 unable to read partition table WARNING: USB Mass Storage data integrity not assured USB Mass Storage device found at 8 searching google, i found some references that ejecting the device may solve the "READ CAPACITY failed" error. then i get: sdc: Write Protect is off sdc: I/O error: dev 08:20, sector 0 I/O error: dev 08:20, sector 0 unable to read partition table Jurgen. -- I will not charge admission to the bathroom. Linux sparkie 2.4.19 #2 Sat Sep 21 16:05:31 CEST 2002 sparc64 unknown 8:14pm up 1 day, 3:15, 5 users, load average: 0.00, 0.00, 0.00 ------------------------------------------------------- This sf.net email is sponsored by:ThinkGeek Welcome to geek heaven. http://thinkgeek.com/sf _______________________________________________ [EMAIL PROTECTED] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-users
